[EXTERNAL] Re: [PATCH v5 1/2] dt-bindings: net: Add ICSSG Ethernet
Md Danish Anwar
a0501179 at ti.com
Mon Mar 6 20:57:47 PST 2023
Hi Rob,
On 11/02/23 00:50, Rob Herring wrote:
> On Fri, Feb 10, 2023 at 05:19:56PM +0530, MD Danish Anwar wrote:
>> From: Puranjay Mohan <p-mohan at ti.com>
>>
>> Add a YAML binding document for the ICSSG Programmable real time unit
>> based Ethernet hardware. The ICSSG driver uses the PRU and PRUSS consumer
>> APIs to interface the PRUs and load/run the firmware for supporting
>> ethernet functionality.
>>
>> Signed-off-by: Puranjay Mohan <p-mohan at ti.com>
>> Signed-off-by: Md Danish Anwar <danishanwar at ti.com>
>> ---
>> .../bindings/net/ti,icssg-prueth.yaml | 184 ++++++++++++++++++
>> 1 file changed, 184 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml b/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml
>> new file mode 100644
>> index 000000000000..8b860f29ecc0
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml
>> @@ -0,0 +1,184 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/net/ti,icssg-prueth.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Texas Instruments ICSSG PRUSS Ethernet
>> +
>> +maintainers:
>> + - Md Danish Anwar <danishanwar at ti.com>
>> +
>> +description:
>> + Ethernet based on the Programmable Real-Time
>> + Unit and Industrial Communication Subsystem.
>
> Odd line wrap length. It should be 80 chars.
>
Sure, I will modify it.
>> +
>> +allOf:
>> + - $ref: /schemas/remoteproc/ti,pru-consumer.yaml#
>> +
>> +properties:
>> + compatible:
>> + enum:
>> + - ti,am654-icssg-prueth # for AM65x SoC family
>> +
>> + ti,sram:
>> + $ref: /schemas/types.yaml#/definitions/phandle
>> + description:
>> + phandle to MSMC SRAM node
>
> I believe we have a standard 'sram' property to point to SRAM nodes
> assuming this is just mmio-sram or similar.
>
Yes, we have standard 'sram' property but Krzysztof had asked me to make the
sram property vendor specific in last revision of this series.
>> +
>> + dmas:
>> + maxItems: 10
>> +
>> + dma-names:
>> + items:
>> + - const: tx0-0
>> + - const: tx0-1
>> + - const: tx0-2
>> + - const: tx0-3
>> + - const: tx1-0
>> + - const: tx1-1
>> + - const: tx1-2
>> + - const: tx1-3
>> + - const: rx0
>> + - const: rx1
>> +
>> + ti,mii-g-rt:
>> + $ref: /schemas/types.yaml#/definitions/phandle
>> + description: |
>> + phandle to MII_G_RT module's syscon regmap.
>> +
>> + ti,mii-rt:
>> + $ref: /schemas/types.yaml#/definitions/phandle
>> + description: |
>> + phandle to MII_RT module's syscon regmap
>> +
>> + interrupts:
>> + maxItems: 2
>> + description: |
>
> Don't need '|'
>
Sure, I will drop this.
>> + Interrupt specifiers to TX timestamp IRQ.
>> +
>> + interrupt-names:
>> + items:
>> + - const: tx_ts0
>> + - const: tx_ts1
>> +
>> + ethernet-ports:
>> + type: object
>> + additionalProperties: false
>> +
>> + properties:
>> + '#address-cells':
>> + const: 1
>> + '#size-cells':
>> + const: 0
>> +
>> + patternProperties:
>> + ^port@[0-1]$:
>> + type: object
>> + description: ICSSG PRUETH external ports
>> + $ref: ethernet-controller.yaml#
>> + unevaluatedProperties: false
>> +
>> + properties:
>> + reg:
>> + items:
>> + - enum: [0, 1]
>> + description: ICSSG PRUETH port number
>> +
>> + interrupts:
>> + maxItems: 1
>> +
>> + ti,syscon-rgmii-delay:
>> + items:
>> + - items:
>> + - description: phandle to system controller node
>> + - description: The offset to ICSSG control register
>> + $ref: /schemas/types.yaml#/definitions/phandle-array
>> + description:
>> + phandle to system controller node and register offset
>> + to ICSSG control register for RGMII transmit delay
>> +
>> + required:
>> + - reg
>> + anyOf:
>> + - required:
>> + - port at 0
>> + - required:
>> + - port at 1
>> +
>> +required:
>> + - compatible
>> + - ti,sram
>> + - dmas
>> + - dma-names
>> + - ethernet-ports
>> + - ti,mii-g-rt
>> + - interrupts
>> + - interrupt-names
>> +
>> +unevaluatedProperties: false
>> +
>> +examples:
>> + - |
>> + /* Example k3-am654 base board SR2.0, dual-emac */
>> + pruss2_eth: ethernet {
>> + compatible = "ti,am654-icssg-prueth";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&icssg2_rgmii_pins_default>;
>> + ti,sram = <&msmc_ram>;
>> +
>> + ti,prus = <&pru2_0>, <&rtu2_0>, <&tx_pru2_0>,
>> + <&pru2_1>, <&rtu2_1>, <&tx_pru2_1>;
>> + firmware-name = "ti-pruss/am65x-pru0-prueth-fw.elf",
>> + "ti-pruss/am65x-rtu0-prueth-fw.elf",
>> + "ti-pruss/am65x-txpru0-prueth-fw.elf",
>> + "ti-pruss/am65x-pru1-prueth-fw.elf",
>> + "ti-pruss/am65x-rtu1-prueth-fw.elf",
>> + "ti-pruss/am65x-txpru1-prueth-fw.elf";
>> + ti,pruss-gp-mux-sel = <2>, /* MII mode */
>> + <2>,
>> + <2>,
>> + <2>, /* MII mode */
>> + <2>,
>> + <2>;
>> + dmas = <&main_udmap 0xc300>, /* egress slice 0 */
>> + <&main_udmap 0xc301>, /* egress slice 0 */
>> + <&main_udmap 0xc302>, /* egress slice 0 */
>> + <&main_udmap 0xc303>, /* egress slice 0 */
>> + <&main_udmap 0xc304>, /* egress slice 1 */
>> + <&main_udmap 0xc305>, /* egress slice 1 */
>> + <&main_udmap 0xc306>, /* egress slice 1 */
>> + <&main_udmap 0xc307>, /* egress slice 1 */
>> + <&main_udmap 0x4300>, /* ingress slice 0 */
>> + <&main_udmap 0x4301>; /* ingress slice 1 */
>> + dma-names = "tx0-0", "tx0-1", "tx0-2", "tx0-3",
>> + "tx1-0", "tx1-1", "tx1-2", "tx1-3",
>> + "rx0", "rx1";
>> + ti,mii-g-rt = <&icssg2_mii_g_rt>;
>> + interrupt-parent = <&icssg2_intc>;
>> + interrupts = <24 0 2>, <25 1 3>;
>> + interrupt-names = "tx_ts0", "tx_ts1";
>> + ethernet-ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + pruss2_emac0: port at 0 {
>> + reg = <0>;
>> + phy-handle = <&pruss2_eth0_phy>;
>> + phy-mode = "rgmii-id";
>> + interrupts-extended = <&icssg2_intc 24>;
>> + ti,syscon-rgmii-delay = <&scm_conf 0x4120>;
>> + /* Filled in by bootloader */
>> + local-mac-address = [00 00 00 00 00 00];
>> + };
>> +
>> + pruss2_emac1: port at 1 {
>> + reg = <1>;
>> + phy-handle = <&pruss2_eth1_phy>;
>> + phy-mode = "rgmii-id";
>> + interrupts-extended = <&icssg2_intc 25>;
>> + ti,syscon-rgmii-delay = <&scm_conf 0x4124>;
>> + /* Filled in by bootloader */
>> + local-mac-address = [00 00 00 00 00 00];
>> + };
>> + };
>> + };
>> --
>> 2.25.1
>>
--
Thanks and Regards,
Danish.
More information about the linux-arm-kernel
mailing list