[PATCH v9 1/5] clk: meson: add support for A1 PLL clock ops

Dmitry Rokosov ddrokosov at sberdevices.ru
Wed Mar 1 10:37:55 PST 2023


From: Jian Hu <jian.hu at amlogic.com>

Modern meson PLL IPs are a little bit different from early known PLLs.
The main difference is located in the init/enable/disable sequences; the
rate logic is the same.
Compared with the previous SoCs, self-adaption current module
is newly added for A1, and there is no reset parameter except the
fixed pll. In A1 PLL, the PLL enable sequence is different, using
the new power-on sequence to enable the PLL.

Signed-off-by: Jian Hu <jian.hu at amlogic.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
Signed-off-by: Dmitry Rokosov <ddrokosov at sberdevices.ru>
---
 drivers/clk/meson/clk-pll.c | 47 +++++++++++++++++++++++++++++++------
 drivers/clk/meson/clk-pll.h |  2 ++
 2 files changed, 42 insertions(+), 7 deletions(-)

diff --git a/drivers/clk/meson/clk-pll.c b/drivers/clk/meson/clk-pll.c
index afefeba6e458..56ec2210f1ad 100644
--- a/drivers/clk/meson/clk-pll.c
+++ b/drivers/clk/meson/clk-pll.c
@@ -295,10 +295,14 @@ static int meson_clk_pll_init(struct clk_hw *hw)
 	struct meson_clk_pll_data *pll = meson_clk_pll_data(clk);
 
 	if (pll->init_count) {
-		meson_parm_write(clk->map, &pll->rst, 1);
+		if (MESON_PARM_APPLICABLE(&pll->rst))
+			meson_parm_write(clk->map, &pll->rst, 1);
+
 		regmap_multi_reg_write(clk->map, pll->init_regs,
 				       pll->init_count);
-		meson_parm_write(clk->map, &pll->rst, 0);
+
+		if (MESON_PARM_APPLICABLE(&pll->rst))
+			meson_parm_write(clk->map, &pll->rst, 0);
 	}
 
 	return 0;
@@ -309,8 +313,11 @@ static int meson_clk_pll_is_enabled(struct clk_hw *hw)
 	struct clk_regmap *clk = to_clk_regmap(hw);
 	struct meson_clk_pll_data *pll = meson_clk_pll_data(clk);
 
-	if (meson_parm_read(clk->map, &pll->rst) ||
-	    !meson_parm_read(clk->map, &pll->en) ||
+	if (MESON_PARM_APPLICABLE(&pll->rst) &&
+	    meson_parm_read(clk->map, &pll->rst))
+		return 0;
+
+	if (!meson_parm_read(clk->map, &pll->en) ||
 	    !meson_parm_read(clk->map, &pll->l))
 		return 0;
 
@@ -341,13 +348,34 @@ static int meson_clk_pll_enable(struct clk_hw *hw)
 		return 0;
 
 	/* Make sure the pll is in reset */
-	meson_parm_write(clk->map, &pll->rst, 1);
+	if (MESON_PARM_APPLICABLE(&pll->rst))
+		meson_parm_write(clk->map, &pll->rst, 1);
 
 	/* Enable the pll */
 	meson_parm_write(clk->map, &pll->en, 1);
 
 	/* Take the pll out reset */
-	meson_parm_write(clk->map, &pll->rst, 0);
+	if (MESON_PARM_APPLICABLE(&pll->rst))
+		meson_parm_write(clk->map, &pll->rst, 0);
+
+	/*
+	 * Compared with the previous SoCs, self-adaption current module
+	 * is newly added for A1, keep the new power-on sequence to enable the
+	 * PLL. The sequence is:
+	 * 1. enable the pll, delay for 10us
+	 * 2. enable the pll self-adaption current module, delay for 40us
+	 * 3. enable the lock detect module
+	 */
+	if (MESON_PARM_APPLICABLE(&pll->current_en)) {
+		usleep_range(10, 20);
+		meson_parm_write(clk->map, &pll->current_en, 1);
+		usleep_range(40, 50);
+	};
+
+	if (MESON_PARM_APPLICABLE(&pll->l_detect)) {
+		meson_parm_write(clk->map, &pll->l_detect, 1);
+		meson_parm_write(clk->map, &pll->l_detect, 0);
+	}
 
 	if (meson_clk_pll_wait_lock(hw))
 		return -EIO;
@@ -361,10 +389,15 @@ static void meson_clk_pll_disable(struct clk_hw *hw)
 	struct meson_clk_pll_data *pll = meson_clk_pll_data(clk);
 
 	/* Put the pll is in reset */
-	meson_parm_write(clk->map, &pll->rst, 1);
+	if (MESON_PARM_APPLICABLE(&pll->rst))
+		meson_parm_write(clk->map, &pll->rst, 1);
 
 	/* Disable the pll */
 	meson_parm_write(clk->map, &pll->en, 0);
+
+	/* Disable PLL internal self-adaption current module */
+	if (MESON_PARM_APPLICABLE(&pll->current_en))
+		meson_parm_write(clk->map, &pll->current_en, 0);
 }
 
 static int meson_clk_pll_set_rate(struct clk_hw *hw, unsigned long rate,
diff --git a/drivers/clk/meson/clk-pll.h b/drivers/clk/meson/clk-pll.h
index 367efd0f6410..a2228c0fdce5 100644
--- a/drivers/clk/meson/clk-pll.h
+++ b/drivers/clk/meson/clk-pll.h
@@ -36,6 +36,8 @@ struct meson_clk_pll_data {
 	struct parm frac;
 	struct parm l;
 	struct parm rst;
+	struct parm current_en;
+	struct parm l_detect;
 	const struct reg_sequence *init_regs;
 	unsigned int init_count;
 	const struct pll_params_table *table;
-- 
2.36.0




More information about the linux-arm-kernel mailing list