[PATCH 2/2] arm64: dts: add support for T7 based Amlogic AN400

[Xianwei Zhao]

Hi Krzysztof,
       Thank you for your review.

On 2023/6/26 23:41, Krzysztof Kozlowski wrote:
> [ EXTERNAL EMAIL ]
>
> On 26/06/2023 11:52, Xianwei Zhao wrote:
>> Amlogic T7 is an advanced application processor designed for smart display.
>>
>> Add basic support for the T7 based Amlogic AN400 board, which describes
>> the following components: CPU, GIC, IRQ, Timer, UART. It's capable of
>> booting up into the serial console.
> Few nits.
Is it possible to be more specific about it?
> ...
>
>> +                             core3 {
>> +                                     cpu = <&cpu7>;
>> +                             };
>> +                     };
>> +             };
>> +
>> +             cpu0:cpu at 0 {
> You miss spaces after labels.
Will do.
>
>> +                     device_type = "cpu";
>> +                     compatible = "arm,cortex-a73";
>> +                     reg = <0x0 0x0>;
>> +                     enable-method = "psci";
>> +             };
>> +
>> +             cpu1:cpu at 1 {
>> +                     device_type = "cpu";
>> +                     compatible = "arm,cortex-a73";
>> +                     reg = <0x0 0x1>;
>> +                     enable-method = "psci";
>> +             };
>> +
>> +             cpu2:cpu at 2 {
>> +                     device_type = "cpu";
>> +                     compatible = "arm,cortex-a73";
>> +                     reg = <0x0 0x2>;
>> +                     enable-method = "psci";
>> +             };
>> +
>> +             cpu3:cpu at 3 {
>> +                     device_type = "cpu";
>> +                     compatible = "arm,cortex-a73";
>> +                     reg = <0x0 0x3>;
>> +                     enable-method = "psci";
>> +             };
>> +
>> +             cpu4:cpu at 100 {
>> +                     device_type = "cpu";
>> +                     compatible = "arm,cortex-a53";
>> +                     reg = <0x0 0x100>;
>> +                     enable-method = "psci";
>> +             };
>> +
>> +             cpu5:cpu at 101{
>> +                     device_type = "cpu";
>> +                     compatible = "arm,cortex-a53";
>> +                     reg = <0x0 0x101>;
>> +                     enable-method = "psci";
>> +             };
>> +
>> +             cpu6:cpu at 102 {
>> +                     device_type = "cpu";
>> +                     compatible = "arm,cortex-a53";
>> +                     reg = <0x0 0x102>;
>> +                     enable-method = "psci";
>> +             };
>> +
>> +             cpu7:cpu at 103 {
>> +                     device_type = "cpu";
>> +                     compatible = "arm,cortex-a53";
>> +                     reg = <0x0 0x103>;
>> +                     enable-method = "psci";
>> +             };
>> +     };
>> +
>> +     timer {
>> +             compatible = "arm,armv8-timer";
>> +             interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>> +                          <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>> +                          <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>> +                          <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
>> +     };
>> +
>> +     psci {
>> +             compatible = "arm,psci-0.2";
>> +             method = "smc";
>> +     };
>> +
>> +     xtal: xtal-clk {
>> +             compatible = "fixed-clock";
>> +             clock-frequency = <24000000>;
>> +             clock-output-names = "xtal";
>> +             #clock-cells = <0>;
>> +     };
>> +
>> +     soc {
>> +             compatible = "simple-bus";
>> +             #address-cells = <2>;
>> +             #size-cells = <2>;
>> +             ranges;
>> +
>> +             gic: interrupt-controller at fff01000 {
>> +                     compatible = "arm,gic-400";
>> +                     #interrupt-cells = <3>;
>> +                     #address-cells = <0>;
>> +                     interrupt-controller;
>> +                     reg = <0x0 0xfff01000 0 0x1000>,
>> +                         <0x0 0xfff02000 0 0x0100>;
>> +                     interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
>> +                  };
> Fix indentation.
Will do.
>> +
>> +             apb4: bus at fe000000 {
>> +                     compatible = "simple-bus";
>> +                     reg = <0x0 0xfe000000 0x0 0x480000>;
>> +                     #address-cells = <2>;
>> +                     #size-cells = <2>;
>> +                     ranges = <0x0 0x0 0x0 0xfe000000 0x0 0x480000>;
>> +
>> +                     uart_a: serial at 78000 {
>> +                             compatible = "amlogic,meson-s4-uart",
>> +                                          "amlogic,meson-ao-uart";
>> +                             reg = <0x0 0x78000 0x0 0x18>;
>> +                             interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
>> +                             status = "disabled";
> Please, don't put status in the middle of properties...
Will put status in the end of properties in next version.
>
>
>
> Best regards,
> Krzysztof
>