[PATCH 1/2] ARM: dts: r8a7740: Add LCDC nodes

[Laurent Pinchart]

Hi Geert,

Thank you for the patch.

On Thu, Jun 22, 2023 at 11:23:14AM +0200, Geert Uytterhoeven wrote:
> Add device nodes for the two LCD Controllers (LCDC) on the R-Mobile A1
> SoC, and for the two optional external LCDL clock inputs.
> 
> Note that the HDMI clock for LCDC1 is not added, as this clock is not
> yet supported.
> 
> Based on a patch by Laurent Pinchart adding the first LCDC device node.
> 
> Signed-off-by: Geert Uytterhoeven <geert+renesas at glider.be>
> ---
> Changes compared to Laurent's original:
>   - Add lcdc0 label,
>   - Rename node from display to lcdc-controller,
>   - Rename compatible value from "renesas,lcdc-r8a7740" to
>     "renesas,r8a7740-lcdc",
>   - Correct syntax of reg property,
>   - Use GIC_SPI macro,
>   - Add more clocks,
>   - Add power-domains property,
>   - Add status disabled,
>   - Remove second port from lcdc0, as only lcdc1 has an HDMI port,
>   - Add lcdc1 device node.
> ---
>  arch/arm/boot/dts/r8a7740.dtsi | 65 ++++++++++++++++++++++++++++++++++
>  1 file changed, 65 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/r8a7740.dtsi b/arch/arm/boot/dts/r8a7740.dtsi
> index 1b2cf5fa322b2985..55884ec701f8dab4 100644
> --- a/arch/arm/boot/dts/r8a7740.dtsi
> +++ b/arch/arm/boot/dts/r8a7740.dtsi
> @@ -398,6 +398,61 @@ sh_fsi2: sound at fe1f0000 {
>  		status = "disabled";
>  	};
>  
> +	lcdc0: lcd-controller at fe940000 {
> +		compatible = "renesas,r8a7740-lcdc";
> +		reg = <0xfe940000 0x4000>;
> +		interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
> +		clocks = <&mstp1_clks R8A7740_CLK_LCDC0>,
> +			 <&cpg_clocks R8A7740_CLK_M3>, <&lcdlclk0_clk>,
> +			 <&vou_clk>;
> +		clock-names = "fck", "media", "lclk", "video";
> +		power-domains = <&pd_a4lc>;
> +		status = "disabled";
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port at 0 {
> +				reg = <0>;
> +
> +				lcdc0_rgb: endpoint {
> +				};
> +			};
> +		};
> +	};
> +
> +	lcdc1: lcd-controller at fe944000 {
> +		compatible = "renesas,r8a7740-lcdc";
> +		reg = <0xfe944000 0x4000>;
> +		interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
> +		clocks = <&mstp1_clks R8A7740_CLK_LCDC1>,
> +			 <&cpg_clocks R8A7740_CLK_M3>, <&lcdlclk1_clk>,
> +			 <&vou_clk>;
> +		clock-names = "fck", "media", "lclk", "video";
> +		power-domains = <&pd_a4lc>;
> +		status = "disabled";
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port at 0 {
> +				reg = <0>;
> +
> +				lcdc1_rgb: endpoint {
> +				};
> +			};
> +
> +			port at 1 {
> +				reg = <1>;
> +
> +				lcdc1_hdmi: endpoint {
> +				};
> +			};
> +		};
> +	};
> +
>  	tmu0: timer at fff80000 {
>  		compatible = "renesas,tmu-r8a7740", "renesas,tmu";
>  		reg = <0xfff80000 0x2c>;
> @@ -474,6 +529,16 @@ fsibck_clk: fsibck {
>  			#clock-cells = <0>;
>  			clock-frequency = <0>;
>  		};
> +		lcdlclk0_clk: lcdlclk0 {
> +			compatible = "fixed-clock";
> +			#clock-cells = <0>;
> +			clock-frequency = <0>;
> +		};
> +		lcdlclk1_clk: lcdlclk1 {
> +			compatible = "fixed-clock";
> +			#clock-cells = <0>;
> +			clock-frequency = <0>;
> +		};

The clock frequency seems quite low :-) As far as I understand, there
are the clocks fed to the external LCDLCLK pins. They belong to the
board DTS, not here. If a board doesn't provide an external clock, the
clock should simply be ommitted. The driver must thus treat it as
optional.

>  
>  		/* Special CPG clocks */
>  		cpg_clocks: cpg_clocks at e6150000 {

-- 
Regards,

Laurent Pinchart