[PATCH v2 8/8] ARM: dts: stm32: lxa-tac: add Linux Automation GmbH TAC
Leonard Göhrs
l.goehrs at pengutronix.de
Wed Jun 14 05:32:22 PDT 2023
The Linux Automation Test Automation Controller (LXA TAC)[1] is an embedded
software development tool built around the Octavo Systems OSD32MP15x SiP.
The device contains an eMMC for storage, a DSA-capable on board ethernet
switch with two external ports, dual CAN busses, a power switch to turn
a device under test on or off and some other I/O.
As of now there are two STM32MP157 based hardware generations (Gen 1 and
Gen 2) that have most of their hardware config in common.
In the future there will also be a STM32MP153 based hardware generation.
[1]: https://www.linux-automation.com/en/products/lxa-tac.html
Signed-off-by: Leonard Göhrs <l.goehrs at pengutronix.de>
---
arch/arm/boot/dts/Makefile | 2 +
.../arm/boot/dts/stm32mp157c-lxa-tac-gen1.dts | 93 +++
.../arm/boot/dts/stm32mp157c-lxa-tac-gen2.dts | 172 +++++
arch/arm/boot/dts/stm32mp15xc-lxa-tac.dtsi | 610 ++++++++++++++++++
4 files changed, 877 insertions(+)
create mode 100644 arch/arm/boot/dts/stm32mp157c-lxa-tac-gen1.dts
create mode 100644 arch/arm/boot/dts/stm32mp157c-lxa-tac-gen2.dts
create mode 100644 arch/arm/boot/dts/stm32mp15xc-lxa-tac.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4c1c96000f3bf..d73c3534506a1 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1266,6 +1266,8 @@ dtb-$(CONFIG_ARCH_STM32) += \
stm32mp157c-ev1.dtb \
stm32mp157c-ev1-scmi.dtb \
stm32mp157c-lxa-mc1.dtb \
+ stm32mp157c-lxa-tac-gen1.dtb \
+ stm32mp157c-lxa-tac-gen2.dtb \
stm32mp157c-odyssey.dtb \
stm32mp157c-phycore-stm32mp1-3.dtb
dtb-$(CONFIG_MACH_SUN4I) += \
diff --git a/arch/arm/boot/dts/stm32mp157c-lxa-tac-gen1.dts b/arch/arm/boot/dts/stm32mp157c-lxa-tac-gen1.dts
new file mode 100644
index 0000000000000..81f254fb88b0a
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-lxa-tac-gen1.dts
@@ -0,0 +1,93 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2021 Rouven Czerwinski, Pengutronix
+ * Copyright (C) 2023 Leonard Göhrs, Pengutronix
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc-lxa-tac.dtsi"
+
+/ {
+ model = "Linux Automation Test Automation Controller (TAC) Gen 1";
+ compatible = "lxa,stm32mp157c-tac-gen1", "oct,stm32mp15xx-osd32", "st,stm32mp157";
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ power-supply = <&v3v3>;
+
+ brightness-levels = <0 31 63 95 127 159 191 223 255>;
+ default-brightness-level = <7>;
+ pwms = <&backlight_pwm 1 1000000 0>;
+ };
+
+ reg_iobus_12v: regulator-iobus-12v {
+ compatible = "regulator-fixed";
+ vin-supply = <®_12v>;
+
+ gpio = <&gpioh 13 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-max-microvolt = <12000000>;
+ regulator-min-microvolt = <12000000>;
+ regulator-name = "12V_IOBUS";
+ };
+};
+
+&gpioa {
+ gpio-line-names = "", "", "STACK_CS2", "", "STACK_CS3", /* 0 */
+ "ETH_GPIO1", "ETH_INT", "", "", "", /* 5 */
+ "", "", "", "BOOTROM_LED", "ETH_LAB_LEDRP", /* 10 */
+ ""; /* 15 */
+};
+
+&gpioc {
+ gpio-line-names = "", "STACK_CS1", "", "", "", /* 0 */
+ "", "", "", "", "", /* 5 */
+ "", ""; /* 10 */
+};
+
+&gpu {
+ status = "disabled";
+};
+
+&i2c1 {
+ powerboard_gpio: gpio at 24 {
+ compatible = "nxp,pca9570";
+ reg = <0x24>;
+
+ #gpio-cells = <2>;
+ gpio-controller;
+ gpio-line-names = "DUT_PWR_EN", "DUT_PWR_DISCH", "DUT_PWR_ADCRST", "";
+ };
+};
+
+&spi2 {
+ adc at 0 {
+ compatible = "ti,lmp92064";
+ reg = <0>;
+ spi-max-frequency = <5000000>;
+ vdd-supply = <®_pb_3v3>;
+ vdig-supply = <®_pb_3v3>;
+ reset-gpios = <&powerboard_gpio 2 GPIO_ACTIVE_HIGH>;
+
+ shunt-resistor-micro-ohms = <15000>;
+ };
+};
+
+&timers1 {
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ status = "okay";
+
+ backlight_pwm: pwm {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&pwm1_pins_c>;
+ pinctrl-1 = <&pwm1_sleep_pins_c>;
+
+ status = "okay";
+ };
+};
diff --git a/arch/arm/boot/dts/stm32mp157c-lxa-tac-gen2.dts b/arch/arm/boot/dts/stm32mp157c-lxa-tac-gen2.dts
new file mode 100644
index 0000000000000..8a34d15e9005f
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-lxa-tac-gen2.dts
@@ -0,0 +1,172 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2021 Rouven Czerwinski, Pengutronix
+ * Copyright (C) 2023 Leonard Göhrs, Pengutronix
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc-lxa-tac.dtsi"
+
+/ {
+ model = "Linux Automation Test Automation Controller (TAC) Gen 2";
+ compatible = "lxa,stm32mp157c-tac-gen2", "oct,stm32mp15xx-osd32", "st,stm32mp157";
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ power-supply = <&v3v3>;
+
+ brightness-levels = <0 31 63 95 127 159 191 223 255>;
+ default-brightness-level = <7>;
+ pwms = <&led_pwm 3 1000000 0>;
+ };
+
+ reg_iobus_12v: regulator-iobus-12v {
+ compatible = "regulator-fixed";
+ vin-supply = <®_12v>;
+ gpio = <&gpioh 13 GPIO_ACTIVE_LOW>;
+ regulator-max-microvolt = <12000000>;
+ regulator-min-microvolt = <12000000>;
+ regulator-name = "12V_IOBUS";
+ };
+
+ led-controller-1 {
+ compatible = "pwm-leds-multicolor";
+
+ multi-led {
+ color = <LED_COLOR_ID_RGB>;
+ function = LED_FUNCTION_STATUS;
+ max-brightness = <65535>;
+
+ led-red {
+ active-low;
+ color = <LED_COLOR_ID_RED>;
+ pwms = <&led_pwm 0 1000000 0>;
+ };
+
+ led-green {
+ active-low;
+ color = <LED_COLOR_ID_GREEN>;
+ pwms = <&led_pwm 2 1000000 0>;
+ };
+
+ led-blue {
+ active-low;
+ color = <LED_COLOR_ID_BLUE>;
+ pwms = <&led_pwm 1 1000000 0>;
+ };
+ };
+ };
+
+ led-controller-2 {
+ compatible = "gpio-leds";
+
+ led-5 {
+ label = "tac:green:iobus";
+ gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-6 {
+ label = "tac:green:can";
+ gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-7 {
+ label = "tac:green:out0";
+ gpios = <&gpiob 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-8 {
+ label = "tac:green:out1";
+ gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-9 {
+ label = "tac:green:uarttx";
+ gpios = <&gpiod 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-10 {
+ label = "tac:green:uartrx";
+ gpios = <&gpiof 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-11 {
+ label = "tac:green:usbh1";
+ gpios = <&gpioc 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-12 {
+ label = "tac:green:usbh2";
+ gpios = <&gpiod 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-13 {
+ label = "tac:green:usbh3";
+ gpios = <&gpiob 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-14 {
+ label = "tac:green:usbg";
+ gpios = <&gpiod 14 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "usb-gadget";
+ };
+
+ led-15 {
+ label = "tac:green:dutpwr";
+ gpios = <&gpioa 15 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&gpioa {
+ gpio-line-names = "", "", "DUT_PWR_EN", "", "STACK_CS3", /* 0 */
+ "ETH_GPIO1", "ETH_INT", "", "", "", /* 5 */
+ "", "", "", "BOOTROM_LED", "ETH_LAB_LEDRP", /* 10 */
+ ""; /* 15 */
+};
+
+&gpioc {
+ gpio-line-names = "", "DUT_PWR_DISCH", "", "", "", /* 0 */
+ "", "", "", "", "", /* 5 */
+ "", ""; /* 10 */
+};
+
+&gpu {
+ status = "disabled";
+};
+
+&m_can2 {
+ termination-gpios = <&gpioe 4 GPIO_ACTIVE_HIGH>;
+ termination-ohms = <120>;
+};
+
+&spi2 {
+ adc at 0 {
+ compatible = "ti,lmp92064";
+ reg = <0>;
+
+ reset-gpios = <&gpioa 4 GPIO_ACTIVE_HIGH>;
+ shunt-resistor-micro-ohms = <15000>;
+ spi-max-frequency = <5000000>;
+ vdd-supply = <®_pb_3v3>;
+ vdig-supply = <®_pb_3v3>;
+ };
+};
+
+&timers8 {
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ status = "okay";
+
+ led_pwm: pwm {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&pwm8_pins_b>;
+ pinctrl-1 = <&pwm8_sleep_pins_b>;
+ status = "okay";
+ };
+};
diff --git a/arch/arm/boot/dts/stm32mp15xc-lxa-tac.dtsi b/arch/arm/boot/dts/stm32mp15xc-lxa-tac.dtsi
new file mode 100644
index 0000000000000..184b8bb4ebbf6
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp15xc-lxa-tac.dtsi
@@ -0,0 +1,610 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2021 Rouven Czerwinski, Pengutronix
+ * Copyright (C) 2023 Leonard Göhrs, Pengutronix
+ */
+
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-osd32.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ aliases {
+ ethernet0 = ðernet0;
+ ethernet1 = &port_uplink;
+ ethernet2 = &port_dut;
+ mmc1 = &sdmmc2;
+ serial0 = &uart4;
+ serial1 = &usart3;
+ };
+
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ led-controller-0 {
+ compatible = "gpio-leds";
+
+ led-0 {
+ label = "tac:green:user1";
+ gpios = <&gpiof 10 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-1 {
+ label = "tac:green:user2";
+ gpios = <&gpiog 7 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-2 {
+ label = "tac:green:statusdut";
+ gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+ };
+
+ /* led-3 and led-4 are internally connected antiparallel to one
+ * another inside the ethernet jack like this:
+ * GPIOA14 ---+---|led-3|>--+--- GPIOD15
+ * +--<|led-4|---+
+ * E.g. only one of the LEDs can be illuminated at a time while
+ * the other output must be driven low.
+ * This should likely be implemented using a multi color LED
+ * driver for antiparallel LEDs.
+ */
+ led-3 {
+ label = "tac:green:statuslab";
+ gpios = <&gpioa 14 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-4 {
+ label = "tac:orange:statuslab";
+ gpios = <&gpiod 15 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ button-lower {
+ label = "USER_BTN2";
+ linux,code = <KEY_ESC>;
+ gpios = <&gpioe 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ };
+
+ button-upper {
+ label = "USER_BTN";
+ linux,code = <KEY_HOME>;
+ gpios = <&gpioi 11 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ };
+ };
+
+ /* supplied by either barrel connector or PoE */
+ reg_12v: regulator-12v {
+ compatible = "regulator-fixed";
+ regulator-name = "12V";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ };
+
+ reg_5v: regulator-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <®_12v>;
+ };
+
+ reg_1v2: regulator-1v2 {
+ compatible = "regulator-fixed";
+ regulator-name = "1V2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ vin-supply = <®_5v>;
+ };
+
+ reg_pb_5v: regulator-pb-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "5V_POWERBOARD";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <®_5v>;
+ };
+
+ reg_pb_3v3: regulator-pb-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3_POWERBOARD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ vin-supply = <®_pb_5v>;
+ };
+
+ output-iobus-12v {
+ compatible = "regulator-output";
+ vout-supply = <®_iobus_12v>;
+ };
+
+ output-vuart {
+ compatible = "regulator-output";
+ vout-supply = <&v3v3_hdmi>;
+ };
+};
+
+baseboard_eeprom: &sip_eeprom {
+};
+
+&adc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&adc1_ain_pins_a>;
+ vdd-supply = <&vdd>;
+ vdda-supply = <&vdda>;
+ vref-supply = <&vrefbuf>;
+ status = "okay";
+
+ adc1: adc at 0 {
+ st,adc-channels = <0 1 2 5 9 10 13 15>;
+ st,min-sample-time-nsecs = <5000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ channel at 0 {
+ reg = <0>;
+ label = "HOST_2_CURR_FB";
+ };
+
+ channel at 1 {
+ reg = <1>;
+ label = "HOST_3_CURR_FB";
+ };
+
+ channel at 2 {
+ reg = <2>;
+ label = "OUT_0_FB";
+ };
+
+ channel at 5 {
+ reg = <5>;
+ label = "IOBUS_CURR_FB";
+ };
+
+ channel at 9 {
+ reg = <9>;
+ label = "IOBUS_VOLT_FB";
+ };
+
+ channel at 10 {
+ reg = <10>;
+ label = "OUT_1_FB";
+ };
+
+ channel at 13 {
+ reg = <13>;
+ label = "HOST_CURR_FB";
+ };
+
+ channel at 15 {
+ reg = <15>;
+ label = "HOST_1_CURR_FB";
+ };
+ };
+
+ adc2: adc at 100 {
+ st,adc-channels = <12>;
+ st,min-sample-time-nsecs = <500000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ channel at 12 {
+ reg = <12>;
+ label = "TEMP_INTERNAL";
+ };
+ };
+};
+
+&crc1 {
+ status = "okay";
+};
+
+&cryp1 {
+ status = "okay";
+};
+
+&dts {
+ status = "okay";
+};
+
+ðernet0 {
+ assigned-clocks = <&rcc ETHCK_K>, <&rcc PLL4_P>;
+ assigned-clock-parents = <&rcc PLL4_P>;
+ assigned-clock-rates = <125000000>; /* Clock PLL4 to 750Mhz in ATF */
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <ðernet0_rgmii_pins_e>;
+ pinctrl-1 = <ðernet0_rgmii_sleep_pins_e>;
+
+ st,eth-clk-sel;
+ phy-mode = "rgmii-id";
+
+ status = "okay";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+ðernet0_rgmii_pins_e {
+ pins1 {
+ /* Reduce EMI emission by reducing RGMII drive strength */
+ slew-rate = <1>;
+ };
+};
+
+&gpiob {
+ gpio-line-names = "", "", "", "", "", /* 0 */
+ "", "USB_RESET", "", "", "", /* 5 */
+ "", "", "", "", "", /* 10 */
+ ""; /* 15 */
+};
+
+&gpiod {
+ gpio-line-names = "", "", "", "", "TP38", /* 0 */
+ "TP39", "", "", "TP41", "TP42", /* 5 */
+ "OLED_DC", "", "", "ETH_CS", "", /* 10 */
+ "ETH_LAB_LEDRN"; /* 15 */
+};
+
+&gpioe {
+ gpio-line-names = "TP35", "", "", "", "CAN_1_120R", /* 0 */
+ "", "", "USER_BTN2", "TP48", "UART_TX_EN", /* 5 */
+ "UART_RX_EN", "TP24", "", "TP25", "TP26", /* 10 */
+ "TP27"; /* 15 */
+};
+
+&gpiof {
+ gpio-line-names = "TP36", "TP37", "", "", "OLED_CS", /* 0 */
+ "", "", "", "", "", /* 5 */
+ "USER_LED1", "", "STACK_CS0", "", "", /* 10 */
+ ""; /* 15 */
+};
+
+&gpiog {
+ gpio-line-names = "ETH_RESET", "", "", "", "", /* 0 */
+ "IOBUS_FLT_FB", "", "USER_LED2", "ETH1_PPS_A", "CAN_0_120R", /* 5 */
+ "TP49", "", "", "", "", /* 10 */
+ ""; /* 15 */
+};
+
+&gpioh {
+ gpio-line-names = "", "", "OUT_1", "OUT_0", "OLED_RESET", /* 0 */
+ "", "", "", "", "", /* 5 */
+ "ETH1_PPS_B", "ETH_GPIO2", "", "IOBUS_PWR_EN", "", /* 10 */
+ "TP33"; /* 15 */
+};
+
+&gpioi {
+ gpio-line-names = "TIM_RTS", "", "", "", "DEVICE_DATA_EN", /* 0 */
+ "", "", "", "ETH_WOL", "TP43", /* 5 */
+ "", "USER_BTN"; /* 10 */
+};
+
+&gpioz {
+ gpio-line-names = "HWID0", "HWID1", "HWID2", "HWID3", "", /* 0 */
+ "", "HWID4", "HWID5"; /* 5 */
+};
+
+&hash1 {
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c1_pins_b>;
+ pinctrl-1 = <&i2c1_sleep_pins_b>;
+ status = "okay";
+
+ powerboard_eeprom: eeprom at 50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ vcc-supply = <&v3v3>;
+ };
+
+ temperature-sensor at 48 {
+ compatible = "national,lm75a";
+ reg = <0x48>;
+ status = "disabled";
+ };
+};
+
+&i2c5 {
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c5_pins_b>;
+ pinctrl-1 = <&i2c5_sleep_pins_b>;
+
+ status = "okay";
+
+ usbhub: usbhub at 2c {
+ compatible ="microchip,usb2514b";
+ reg = <0x2c>;
+ vdd-supply = <&v3v3>;
+ reset-gpios = <&gpiob 6 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&iwdg2 {
+ timeout-sec = <8>;
+ status = "okay";
+};
+
+&m_can1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&m_can1_pins_b>;
+ pinctrl-1 = <&m_can1_sleep_pins_b>;
+ status = "okay";
+};
+
+&m_can2 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&m_can2_pins_a>;
+ pinctrl-1 = <&m_can2_sleep_pins_a>;
+ status = "okay";
+};
+
+&pmic {
+ regulators {
+ buck1-supply = <®_5v>; /* VIN */
+ buck2-supply = <®_5v>; /* VIN */
+ buck3-supply = <®_5v>; /* VIN */
+ buck4-supply = <®_5v>; /* VIN */
+ ldo2-supply = <®_5v>; /* PMIC_LDO25IN */
+ ldo4-supply = <®_5v>; /* VIN */
+ ldo5-supply = <®_5v>; /* PMIC_LDO25IN */
+ vref_ddr-supply = <®_5v>; /* VIN */
+ boost-supply = <®_5v>; /* PMIC_BSTIN */
+ pwr_sw2-supply = <&bst_out>; /* PMIC_SWIN */
+ };
+};
+
+&pwr_regulators {
+ vdd-supply = <&vdd>;
+ vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sdmmc2 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
+ pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>;
+ pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>;
+ vmmc-supply = <&v3v3>;
+
+ bus-width = <8>;
+ mmc-ddr-3_3v;
+ no-1-8-v;
+ non-removable;
+ no-sd;
+ no-sdio;
+ st,neg-edge;
+
+ status = "okay";
+};
+
+&spi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_c>;
+ cs-gpios = <&gpiof 12 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&spi4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi4_pins_a>;
+ cs-gpios = <&gpiof 4 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ lcd: display at 0 {
+ compatible = "shineworld,lh133k", "panel-mipi-dbi-spi";
+ reg = <0>;
+ power-supply = <&v3v3>;
+ io-supply = <&v3v3>;
+ backlight = <&backlight>;
+ dc-gpios = <&gpiod 10 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpioh 4 GPIO_ACTIVE_HIGH>;
+ spi-3wire;
+ spi-max-frequency = <32000000>;
+
+ width-mm = <23>;
+ height-mm = <23>;
+ rotation = <180>;
+
+ panel-timing {
+ hactive = <240>;
+ vactive = <240>;
+ hback-porch = <0>;
+ vback-porch = <0>;
+
+ clock-frequency = <0>;
+ hfront-porch = <0>;
+ hsync-len = <0>;
+ vfront-porch = <0>;
+ vsync-len = <0>;
+ };
+ };
+};
+
+&spi5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi5_pins_a>;
+
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ cs-gpios = <&gpiod 13 GPIO_ACTIVE_LOW>;
+
+ status = "okay";
+
+ switch: switch at 0 {
+ compatible = "microchip,ksz9563";
+ reg = <0>;
+
+ reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>;
+ spi-max-frequency = <44000000>;
+
+ interrupt-parent = <&gpioa>;
+ interrupts = <6 IRQ_TYPE_EDGE_RISING>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port_dut: port at 0 {
+ reg = <0>;
+ label = "dut";
+ };
+
+ port_uplink: port at 1 {
+ reg = <1>;
+ label = "uplink";
+ };
+
+ port_cpu: port at 2 {
+ reg = <2>;
+ label = "cpu";
+
+ ethernet = <ðernet0>;
+
+ phy-mode = "rgmii-id";
+ rx-internal-delay-ps = <2000>;
+ tx-internal-delay-ps = <2000>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+};
+
+&timers2 {
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ status = "okay";
+
+ timer at 1 {
+ status = "okay";
+ };
+};
+
+&timers3 {
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ status = "okay";
+
+ timer at 2 {
+ status = "okay";
+ };
+};
+
+&timers4 {
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ status = "okay";
+
+ timer at 3 {
+ status = "okay";
+ };
+};
+
+&uart4 {
+ label = "debug";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins_a>;
+
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ status = "okay";
+};
+
+&usart3 {
+ label = "dut";
+ uart-has-rtscts;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&usart3_pins_f>;
+
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ status = "okay";
+};
+
+&usbh_ehci {
+ phys = <&usbphyc_port0>;
+ phy-names = "usb";
+
+ status = "okay";
+};
+
+&usbotg_hs {
+ phys = <&usbphyc_port1 0>;
+ phy-names = "usb2-phy";
+
+ vusb_d-supply = <&vdd_usb>;
+ vusb_a-supply = <®18>;
+
+ dr_mode = "peripheral";
+
+ status = "okay";
+};
+
+&usbphyc {
+ status = "okay";
+};
+
+&usbphyc_port0 {
+ phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+ phy-supply = <&vdd_usb>;
+};
+
+&v3v3_hdmi {
+ /delete-property/regulator-always-on;
+};
+
+&vrefbuf {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ vdda-supply = <&vdda>;
+
+ status = "okay";
+};
--
2.39.2
More information about the linux-arm-kernel
mailing list