[PATCH 04/21] ARM: dts: at91: sam9x7: add device tree for soc

Dharma.B at microchip.com Dharma.B at microchip.com
Thu Jun 8 22:35:51 PDT 2023


On 04/06/23 1:32 am, Varshini Rajendran wrote:
> Add device tree file for SAM9X7 SoC family
> 
> Signed-off-by: Varshini Rajendran <varshini.rajendran at microchip.com>
> [nicolas.ferre at microchip.com: add support for gmac to sam9x7]
> Signed-off-by: Nicolas Ferre <nicolas.ferre at microchip.com>
> [balamanikandan.gunasundar at microchip.com: Add device node csi2host and isc]
> Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar at microchip.com>
> ---
>   arch/arm/boot/dts/sam9x7.dtsi | 1333 +++++++++++++++++++++++++++++++++
>   1 file changed, 1333 insertions(+)
>   create mode 100644 arch/arm/boot/dts/sam9x7.dtsi
> 
> diff --git a/arch/arm/boot/dts/sam9x7.dtsi b/arch/arm/boot/dts/sam9x7.dtsi
> new file mode 100644
> index 000000000000..f98160182fe6
> --- /dev/null
> +++ b/arch/arm/boot/dts/sam9x7.dtsi
> @@ -0,0 +1,1333 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * sam9x7.dtsi - Device Tree Include file for Microchip SAM9X7 SoC family
> + *
> + * Copyright (C) 2022 Microchip Technology Inc. and its subsidiaries
> + *
> + * Author: Varshini Rajendran <varshini.rajendran at microchip.com>
> + */
> +
> +#include <dt-bindings/clock/at91.h>
> +#include <dt-bindings/dma/at91.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/mfd/atmel-flexcom.h>
> +#include <dt-bindings/pinctrl/at91.h>
> +
> +/ {
> +	#address-cells = <1>;
> +	#size-cells = <1>;
> +	model = "Microchip SAM9X7 SoC";
> +	compatible = "microchip,sam9x7";
> +	interrupt-parent = <&aic>;
> +
> +	aliases {
> +		serial0 = &dbgu;
> +		gpio0 = &pioA;
> +		gpio1 = &pioB;
> +		gpio2 = &pioC;
> +		gpio3 = &pioD;
> +	};
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		cpu at 0 {
> +			compatible = "arm,arm926ej-s";
> +			device_type = "cpu";
> +			reg = <0>;
> +		};
> +	};
> +
> +	clocks {
> +		slow_xtal: slow_xtal {
> +			compatible = "fixed-clock";
> +			#clock-cells = <0>;
> +		};
> +
> +		main_xtal: main_xtal {
> +			compatible = "fixed-clock";
> +			#clock-cells = <0>;
> +		};
> +	};
> +
> +	sram: sram at 300000 {
> +		compatible = "mmio-sram";
> +		reg = <0x300000 0x10000>;
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges = <0 0x300000 0x10000>;
> +	};
> +
> +	ahb {
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		usb0: gadget at 500000 {
> +			compatible = "microchip,sam9x60-udc";
> +			reg = <0x500000 0x100000>,
> +			      <0xf803c000 0x400>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			interrupts = <23 IRQ_TYPE_LEVEL_HIGH 2>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 23>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
> +			clock-names = "pclk", "hclk";
> +			assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>;
> +			assigned-clock-rates = <480000000>;
> +			status = "disabled";
> +		};
> +
> +		ohci0: usb at 600000 {
> +			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
> +			reg = <0x600000 0x100000>;
> +			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 22>, <&pmc PMC_TYPE_PERIPHERAL 22>, <&pmc PMC_TYPE_SYSTEM 6>;
> +			clock-names = "ohci_clk", "hclk", "uhpck";
> +			status = "disabled";
> +		};
> +
> +		ehci0: usb at 700000 {
> +			compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
> +			reg = <0x700000 0x100000>;
> +			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
> +			clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_PERIPHERAL 22>;
> +			clock-names = "usb_clk", "ehci_clk";
> +			assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>;
> +			assigned-clock-rates = <480000000>;
> +			status = "disabled";
> +		};
> +
> +		sdmmc0: sdio-host at 80000000 {
> +			compatible = "microchip,sam9x60-sdhci";
> +			reg = <0x80000000 0x300>;
> +			interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 12>, <&pmc PMC_TYPE_GCK 12>;
> +			clock-names = "hclock", "multclk";
> +			assigned-clocks = <&pmc PMC_TYPE_GCK 12>;
> +			assigned-clock-rates = <100000000>;
> +			status = "disabled";
> +		};
> +
> +		sdmmc1: sdio-host at 90000000 {
> +			compatible = "microchip,sam9x60-sdhci";
> +			reg = <0x90000000 0x300>;
> +			interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 26>, <&pmc PMC_TYPE_GCK 26>;
> +			clock-names = "hclock", "multclk";
> +			assigned-clocks = <&pmc PMC_TYPE_GCK 26>;
> +			assigned-clock-rates = <100000000>;
> +			status = "disabled";
> +		};
> +	};
> +
> +	apb {
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		flx4: flexcom at f0000000 {
> +			compatible = "atmel,sama5d2-flexcom";
> +			reg = <0xf0000000 0x200>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0x0 0xf0000000 0x800>;
> +			status = "disabled";
> +
> +			uart4: serial at 200 {
> +				compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> +				reg = <0x200 0x200>;
> +				interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(8))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(9))>;
> +				dma-names = "tx", "rx";
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
> +				clock-names = "usart";
> +				atmel,use-dma-rx;
> +				atmel,use-dma-tx;
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +
> +			spi4: spi at 400 {
> +				compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
> +				reg = <0x400 0x200>;
> +				interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
> +				clock-names = "spi_clk";
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(8))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(9))>;
> +				dma-names = "tx", "rx";
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +
> +			i2c4: i2c at 600 {
> +				compatible = "microchip,sam9x60-i2c";
> +				reg = <0x600 0x200>;
> +				interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(8))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(9))>;
> +				dma-names = "tx", "rx";
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		flx5: flexcom at f0004000 {
> +			compatible = "atmel,sama5d2-flexcom";
> +			reg = <0xf0004000 0x200>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0x0 0xf0004000 0x800>;
> +			status = "disabled";
> +
> +			uart5: serial at 200 {
> +				compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> +				reg = <0x200 0x200>;
> +				interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(10))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(11))>;
> +				dma-names = "tx", "rx";
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
> +				clock-names = "usart";
> +				atmel,use-dma-rx;
> +				atmel,use-dma-tx;
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +
> +			spi5: spi at 400 {
> +				compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
> +				reg = <0x400 0x200>;
> +				interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
> +				clock-names = "spi_clk";
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(10))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(11))>;
> +				dma-names = "tx", "rx";
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +
> +			i2c5: i2c at 600 {
> +				compatible = "microchip,sam9x60-i2c";
> +				reg = <0x600 0x200>;
> +				interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(10))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(11))>;
> +				dma-names = "tx", "rx";
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		dma0: dma-controller at f0008000 {
> +			compatible = "microchip,sam9x60-dma", "atmel,sama5d4-dma";
> +			reg = <0xf0008000 0x1000>;
> +			interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
> +			#dma-cells = <1>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
> +			clock-names = "dma_clk";
> +			status = "disabled";
> +		};
> +
> +		ssc: ssc at f0010000 {
> +			compatible = "atmel,at91sam9g45-ssc";
> +			reg = <0xf0010000 0x4000>;
> +			interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
> +			dmas = <&dma0
> +				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> +				 AT91_XDMAC_DT_PERID(38))>,
> +			       <&dma0
> +				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> +				 AT91_XDMAC_DT_PERID(39))>;
> +			dma-names = "tx", "rx";
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 28>;
> +			clock-names = "pclk";
> +		};
> +
> +		gpu: gfx2d at f0018000 {
> +			compatible = "microchip,sam9x60-gfx2d";
> +			reg = <0xf0018000 0x4000>;
> +			interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 36>;
> +			clock-names = "periph_clk";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		i2s: i2s at f001c000 {
> +			compatible = "microchip,sam9x60-i2smcc";
> +			reg = <0xf001c000 0x100>;
> +			interrupts = <34 IRQ_TYPE_LEVEL_HIGH 7>;
> +			dmas = <&dma0
> +				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> +				 AT91_XDMAC_DT_PERID(36))>,
> +			       <&dma0
> +				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> +				 AT91_XDMAC_DT_PERID(37))>;
> +			dma-names = "tx", "rx";
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 34>, <&pmc PMC_TYPE_GCK 34>;
> +			clock-names = "pclk", "gclk";
> +			status = "disabled";
> +		};
> +
> +		flx11: flexcom at f0020000 {
> +			compatible = "atmel,sama5d2-flexcom";
> +			reg = <0xf0020000 0x200>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0x0 0xf0020000 0x800>;
> +			status = "disabled";
> +
> +			uart11: serial at 200 {
> +				compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> +				reg = <0x200 0x200>;
> +				interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(22))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(23))>;
> +				dma-names = "tx", "rx";
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
> +				clock-names = "usart";
> +				atmel,use-dma-rx;
> +				atmel,use-dma-tx;
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +
> +			i2c11: i2c at 600 {
> +				compatible = "microchip,sam9x60-i2c";
> +				reg = <0x600 0x200>;
> +				interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(22))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(23))>;
> +				dma-names = "tx", "rx";
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		flx12: flexcom at f0024000 {
> +			compatible = "atmel,sama5d2-flexcom";
> +			reg = <0xf0024000 0x200>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0x0 0xf0024000 0x800>;
> +			status = "disabled";
> +
> +			uart12: serial at 200 {
> +				compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> +				reg = <0x200 0x200>;
> +				interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(24))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(25))>;
> +				dma-names = "tx", "rx";
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
> +				clock-names = "usart";
> +				atmel,use-dma-rx;
> +				atmel,use-dma-tx;
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +
> +			i2c12: i2c at 600 {
> +				compatible = "microchip,sam9x60-i2c";
> +				reg = <0x600 0x200>;
> +				interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(24))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(25))>;
> +				dma-names = "tx", "rx";
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		pit64b0: timer at f0028000 {
> +			compatible = "microchip,sam9x60-pit64b";
> +			reg = <0xf0028000 0x100>;
> +			interrupts = <37 IRQ_TYPE_LEVEL_HIGH 7>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 37>, <&pmc PMC_TYPE_GCK 37>;
> +			clock-names = "pclk", "gclk";
> +		};
> +
> +		sha: sha at f002c000 {
> +			compatible = "atmel,at91sam9g46-sha";
> +			reg = <0xf002c000 0x100>;
> +			interrupts = <41 IRQ_TYPE_LEVEL_HIGH 0>;
> +			dmas = <&dma0
> +				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> +				 AT91_XDMAC_DT_PERID(34))>;
> +			dma-names = "tx";
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
> +			clock-names = "sha_clk";
> +		};
> +
> +		trng: trng at f0030000 {
> +			compatible = "microchip,sam9x60-trng";
> +			reg = <0xf0030000 0x100>;
> +			interrupts = <38 IRQ_TYPE_LEVEL_HIGH 0>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
> +			status = "disabled";
> +		};
> +
> +		aes: aes at f0034000 {
> +			compatible = "atmel,at91sam9g46-aes";
> +			reg = <0xf0034000 0x100>;
> +			interrupts = <39 IRQ_TYPE_LEVEL_HIGH 0>;
> +			dmas = <&dma0
> +				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> +				 AT91_XDMAC_DT_PERID(32))>,
> +			       <&dma0
> +				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> +				 AT91_XDMAC_DT_PERID(33))>;
> +			dma-names = "tx", "rx";
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
> +			clock-names = "aes_clk";
> +		};
> +
> +		tdes: tdes at f0038000 {
> +			compatible = "atmel,at91sam9g46-tdes";
> +			reg = <0xf0038000 0x100>;
> +			interrupts = <40 IRQ_TYPE_LEVEL_HIGH 0>;
> +			dmas = <&dma0
> +				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> +				 AT91_XDMAC_DT_PERID(31))>,
> +			       <&dma0
> +				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> +				 AT91_XDMAC_DT_PERID(30))>;
> +			dma-names = "tx", "rx";
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 40>;
> +			clock-names = "tdes_clk";
> +		};
> +
> +		classd: classd at f003c000 {
> +			compatible = "atmel,sama5d2-classd";
> +			reg = <0xf003c000 0x100>;
> +			interrupts = <42 IRQ_TYPE_LEVEL_HIGH 7>;
> +			dmas = <&dma0
> +				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> +				 AT91_XDMAC_DT_PERID(35))>;
> +			dma-names = "tx";
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 42>, <&pmc PMC_TYPE_GCK 42>;
> +			clock-names = "pclk", "gclk";
> +			status = "disabled";
> +		};
> +
> +		pit64b1: timer at f0040000 {
> +			compatible = "microchip,sam9x60-pit64b";
> +			reg = <0xf0040000 0x100>;
> +			interrupts = <58 IRQ_TYPE_LEVEL_HIGH 7>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 58>, <&pmc PMC_TYPE_GCK 58>;
> +			clock-names = "pclk", "gclk";
> +		};
> +
> +		can0: can at f8000000 {
> +			compatible = "bosch,m_can";
> +			reg = <0xf8000000 0x100>, <0x300000 0x7800>;
> +			reg-names = "m_can", "message_ram";
> +			interrupts = <29 IRQ_TYPE_LEVEL_HIGH 0
> +				      68 IRQ_TYPE_LEVEL_HIGH 0>;
> +			interrupt-names = "int0", "int1";
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 29>, <&pmc PMC_TYPE_GCK 29>;
> +			clock-names = "hclk", "cclk";
> +			assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_GCK 29>;
> +			assigned-clock-rates = <480000000>, <40000000>;
> +			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
> +			bosch,mram-cfg = <0x3400 0 0 64 0 0 32 32>;
> +			status = "disabled";
> +		};
> +
> +		can1: can at f8004000 {
> +			compatible = "bosch,m_can";
> +			reg = <0xf8004000 0x100>, <0x300000 0xbc00>;
> +			reg-names = "m_can", "message_ram";
> +			interrupts = <30 IRQ_TYPE_LEVEL_HIGH 0
> +				      69 IRQ_TYPE_LEVEL_HIGH 0>;
> +			interrupt-names = "int0", "int1";
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 30>, <&pmc PMC_TYPE_GCK 30>;
> +			clock-names = "hclk", "cclk";
> +			assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_GCK 30>;
> +			assigned-clock-rates = <480000000>, <40000000>;
> +			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
> +			bosch,mram-cfg = <0x7800 0 0 64 0 0 32 32>;
> +			status = "disabled";
> +		};
> +
> +		tcb: timer at f8008000 {
There are two timer counter blocks available in sam9x7 series so two 
nodes "tcb0: timer at f8008000 and tcb1: timer at f800c000" with interrupts 17 
and 45" have to be defined here.
> +			compatible = "microchip,sam9x60-tcb", "simple-mfd", "syscoFix the compatible string to "atmel,sama5d2-tcb". 
"microchip,sam9x60-tcb" is no longer used.
> +			reg = <0xf8008000 0x100>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 17>, <&clk32k 0>;
> +			clock-names = "t0_clk", "slow_clk";
> +			status = "disabled";
> +		};
> +
> +		flx6: flexcom at f8010000 {
> +			compatible = "atmel,sama5d2-flexcom";
> +			reg = <0xf8010000 0x200>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0x0 0xf8010000 0x800>;
> +			status = "disabled";
> +
> +			uart6: serial at 200 {
> +				compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> +				reg = <0x200 0x200>;
> +				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(12))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(13))>;
> +				dma-names = "tx", "rx";
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
> +				clock-names = "usart";
> +				atmel,use-dma-rx;
> +				atmel,use-dma-tx;
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +
> +			i2c6: i2c at 600 {
> +				compatible = "microchip,sam9x60-i2c";
> +				reg = <0x600 0x200>;
> +				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(12))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(13))>;
> +				dma-names = "tx", "rx";
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		flx7: flexcom at f8014000 {
> +			compatible = "atmel,sama5d2-flexcom";
> +			reg = <0xf8014000 0x200>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0x0 0xf8014000 0x800>;
> +			status = "disabled";
> +
> +			uart7: serial at 200 {
> +				compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> +				reg = <0x200 0x200>;
> +				interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(14))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(15))>;
> +				dma-names = "tx", "rx";
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
> +				clock-names = "usart";
> +				atmel,use-dma-rx;
> +				atmel,use-dma-tx;
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +
> +			i2c7: i2c at 600 {
> +				compatible = "microchip,sam9x60-i2c";
> +				reg = <0x600 0x200>;
> +				interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(14))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(15))>;
> +				dma-names = "tx", "rx";
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		flx8: flexcom at f8018000 {
> +			compatible = "atmel,sama5d2-flexcom";
> +			reg = <0xf8018000 0x200>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0x0 0xf8018000 0x800>;
> +			status = "disabled";
> +
> +			uart8: serial at 200 {
> +				compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> +				reg = <0x200 0x200>;
> +				interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(16))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(17))>;
> +				dma-names = "tx", "rx";
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
> +				clock-names = "usart";
> +				atmel,use-dma-rx;
> +				atmel,use-dma-tx;
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +
> +			i2c8: i2c at 600 {
> +				compatible = "microchip,sam9x60-i2c";
> +				reg = <0x600 0x200>;
> +				interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(16))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(17))>;
> +				dma-names = "tx", "rx";
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		flx0: flexcom at f801c000 {
> +			compatible = "atmel,sama5d2-flexcom";
> +			reg = <0xf801c000 0x200>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0x0 0xf801c000 0x800>;
> +			status = "disabled";
> +
> +			uart0: serial at 200 {
> +				compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> +				reg = <0x200 0x200>;
> +				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(0))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(1))>;
> +				dma-names = "tx", "rx";
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
> +				clock-names = "usart";
> +				atmel,use-dma-rx;
> +				atmel,use-dma-tx;
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +
> +			spi0: spi at 400 {
> +				compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
> +				reg = <0x400 0x200>;
> +				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
> +				clock-names = "spi_clk";
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(0))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(1))>;
> +				dma-names = "tx", "rx";
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +
> +			i2c0: i2c at 600 {
> +				compatible = "microchip,sam9x60-i2c";
> +				reg = <0x600 0x200>;
> +				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(0))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(1))>;
> +				dma-names = "tx", "rx";
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		flx1: flexcom at f8020000 {
> +			compatible = "atmel,sama5d2-flexcom";
> +			reg = <0xf8020000 0x200>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0x0 0xf8020000 0x800>;
> +			status = "disabled";
> +
> +			uart1: serial at 200 {
> +				compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> +				reg = <0x200 0x200>;
> +				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(2))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(3))>;
> +				dma-names = "tx", "rx";
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
> +				clock-names = "usart";
> +				atmel,use-dma-rx;
> +				atmel,use-dma-tx;
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +
> +			spi1: spi at 400 {
> +				compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
> +				reg = <0x400 0x200>;
> +				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
> +				clock-names = "spi_clk";
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(2))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(3))>;
> +				dma-names = "tx", "rx";
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +
> +			i2c1: i2c at 600 {
> +				compatible = "microchip,sam9x60-i2c";
> +				reg = <0x600 0x200>;
> +				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(2))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(3))>;
> +				dma-names = "tx", "rx";
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		flx2: flexcom at f8024000 {
> +			compatible = "atmel,sama5d2-flexcom";
> +			reg = <0xf8024000 0x200>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0x0 0xf8024000 0x800>;
> +			status = "disabled";
> +
> +			uart2: serial at 200 {
> +				compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> +				reg = <0x200 0x200>;
> +				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(4))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(5))>;
> +				dma-names = "tx", "rx";
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
> +				clock-names = "usart";
> +				atmel,use-dma-rx;
> +				atmel,use-dma-tx;
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +
> +			spi2: spi at 400 {
> +				compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
> +				reg = <0x400 0x200>;
> +				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
> +				clock-names = "spi_clk";
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(4))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(5))>;
> +				dma-names = "tx", "rx";
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +
> +			i2c2: i2c at 600 {
> +				compatible = "microchip,sam9x60-i2c";
> +				reg = <0x600 0x200>;
> +				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(4))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(5))>;
> +				dma-names = "tx", "rx";
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		flx3: flexcom at f8028000 {
> +			compatible = "atmel,sama5d2-flexcom";
> +			reg = <0xf8028000 0x200>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0x0 0xf8028000 0x800>;
> +			status = "disabled";
> +
> +			uart3: serial at 200 {
> +				compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> +				reg = <0x200 0x200>;
> +				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(6))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(7))>;
> +				dma-names = "tx", "rx";
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
> +				clock-names = "usart";
> +				atmel,use-dma-rx;
> +				atmel,use-dma-tx;
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +
> +			spi3: spi at 400 {
> +				compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
> +				reg = <0x400 0x200>;
> +				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
> +				clock-names = "spi_clk";
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(6))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(7))>;
> +				dma-names = "tx", "rx";
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +
> +			i2c3: i2c at 600 {
> +				compatible = "microchip,sam9x60-i2c";
> +				reg = <0x600 0x200>;
> +				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(6))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(7))>;
> +				dma-names = "tx", "rx";
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		gmac: ethernet at f802c000 {
> +			compatible = "microchip,sam9x7-gem";
> +			reg = <0xf802c000 0x1000>;
> +			interrupts = <24 IRQ_TYPE_LEVEL_HIGH 3		/* Queue 0 */
> +				      60 IRQ_TYPE_LEVEL_HIGH 3          /* Queue 1 */
> +				      61 IRQ_TYPE_LEVEL_HIGH 3          /* Queue 2 */
> +				      62 IRQ_TYPE_LEVEL_HIGH 3          /* Queue 3 */
> +				      63 IRQ_TYPE_LEVEL_HIGH 3          /* Queue 4 */
> +				      64 IRQ_TYPE_LEVEL_HIGH 3>;        /* Queue 5 */
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 24>, <&pmc PMC_TYPE_PERIPHERAL 24>;
> +			clock-names = "hclk", "pclk";
> +			status = "disabled";
> +		};
> +
> +		flx9: flexcom at f8040000 {
> +			compatible = "atmel,sama5d2-flexcom";
> +			reg = <0xf8040000 0x200>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0x0 0xf8040000 0x800>;
> +			status = "disabled";
> +
> +			uart9: serial at 200 {
> +				compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> +				reg = <0x200 0x200>;
> +				interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(18))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(19))>;
> +				dma-names = "tx", "rx";
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
> +				clock-names = "usart";
> +				atmel,use-dma-rx;
> +				atmel,use-dma-tx;
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +
> +			i2c9: i2c at 600 {
> +				compatible = "microchip,sam9x60-i2c";
> +				reg = <0x600 0x200>;
> +				interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(18))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(19))>;
> +				dma-names = "tx", "rx";
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		flx10: flexcom at f8044000 {
> +			compatible = "atmel,sama5d2-flexcom";
> +			reg = <0xf8044000 0x200>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0x0 0xf8044000 0x800>;
> +			status = "disabled";
> +
> +			uart10: serial at 200 {
> +				compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> +				reg = <0x200 0x200>;
> +				interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(20))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(21))>;
> +				dma-names = "tx", "rx";
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
> +				clock-names = "usart";
> +				atmel,use-dma-rx;
> +				atmel,use-dma-tx;
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +
> +			i2c10: i2c at 600 {
> +				compatible = "microchip,sam9x60-i2c";
> +				reg = <0x600 0x200>;
> +				interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(20))>,
> +					<&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) |
> +					 AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(21))>;
> +				dma-names = "tx", "rx";
> +				atmel,fifo-size = <16>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		xisc: xisc at f8048000 {
> +			compatible = "microchip,sama7g5-isc";
> +			reg = <0xf8048000 0x2000>;
> +			interrupts = <43 IRQ_TYPE_LEVEL_HIGH 7>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 43>;
> +			clock-names = "hclock";
> +			#clock-cells = <0>;
> +			clock-output-names = "isc-mck";
> +			status = "disabled";
> +
> +			port {
> +				xisc_in: endpoint {
> +					bus-width = <14>;
> +					hsync-active = <1>;
> +					vsync-active = <1>;
> +					remote-endpoint = <&csi2dc_out>;
> +				};
> +			};
> +		};
> +
> +		sfr: sfr at f8050000 {
> +			compatible = "microchip,sam9x60-sfr", "syscon";
> +			reg = <0xf8050000 0x100>;
> +		};
> +
> +		csi2host: csi2host at f8058000 {
> +			compatible = "snps,dw-csi";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0xf8058000 0x7FF>;
> +			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 53>, <&pmc PMC_TYPE_GCK 55>;
> +			clock-names = "perclk", "phyclk";
> +			assigned-clocks = <&pmc PMC_TYPE_GCK 55>;
> +			assigned-clock-rates = <26600000>;
> +			snps,output-type = <1>;
> +			phys = <&csi_dphy>;
> +			status = "disabled";
> +
> +			port at 1 {
> +				reg = <1>;
> +				csi2host_in: endpoint {
> +				};
> +			};
> +
> +			port at 2 {
> +				reg = <2>;
> +				csi2host_out: endpoint {
> +				};
> +			};
> +		};
> +
> +		csi_dphy: dphy at f8058040 {
> +			compatible = "snps,dw-dphy-rx";
> +			#phy-cells = <0>;
> +			bus-width = <8>;
> +			snps,dphy-frequency = <900000>;
> +			snps,phy_type = <0>;
> +			reg = <0xf8058040 0x20>;
> +			status = "disabled";
> +		};
> +
> +		csi2dc: csi2dc at f805c000 {
> +			compatible = "microchip,sama7g5-csi2dc";
> +			reg = <0xf805c000 0x500>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 52>, <&xisc>;
> +			clock-names = "pclk", "scck";
> +			assigned-clocks = <&xisc>;
> +			assigned-clock-rates = <266000000>;
> +			status = "disabled";
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				port at 0 {
> +					reg = <0>;
> +					csi2dc_in: endpoint {
> +					};
> +				};
> +
> +				port at 1 {
> +					reg = <1>;
> +					csi2dc_out: endpoint {
> +						bus-width = <14>;
> +						hsync-active = <1>;
> +						vsync-active = <1>;
> +						remote-endpoint = <&xisc_in>;
> +					};
> +				};
> +			};
> +		};
> +
> +		matrix: matrix at ffffde00 {
> +			compatible = "microchip,sam9x60-matrix", "atmel,at91sam9x5-matrix", "syscon";
> +			reg = <0xffffde00 0x200>;
> +		};
> +
> +		pmecc: ecc-engine at ffffe000 {
> +			compatible = "microchip,sam9x60-pmecc", "atmel,at91sam9g45-pmecc";
> +			reg = <0xffffe000 0x300>,
> +			      <0xffffe600 0x100>;
> +		};
> +
> +		mpddrc: mpddrc at ffffe800 {
> +			compatible = "microchip,sam9x60-ddramc", "atmel,sama5d3-ddramc";
> +			reg = <0xffffe800 0x200>;
> +			clocks = <&pmc PMC_TYPE_SYSTEM 2>, <&pmc PMC_TYPE_CORE PMC_MCK>;
> +			clock-names = "ddrck", "mpddr";
> +		};
> +
> +		smc: smc at ffffea00 {
> +			compatible = "microchip,sam9x60-smc", "atmel,at91sam9260-smc", "syscon";
> +			reg = <0xffffea00 0x100>;
> +		};
> +
> +		aic: interrupt-controller at fffff100 {
> +			compatible = "microchip,sam9x7-aic";
> +			reg = <0xfffff100 0x100>;
> +			#interrupt-cells = <3>;
> +			interrupt-controller;
> +			atmel,external-irqs = <31>;
> +		};
> +
> +		dbgu: serial at fffff200 {
> +			compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
> +			reg = <0xfffff200 0x200>;
> +			interrupts = <47 IRQ_TYPE_LEVEL_HIGH 7>;
> +			dmas = <&dma0
> +				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> +				 AT91_XDMAC_DT_PERID(28))>,
> +			       <&dma0
> +				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> +				 AT91_XDMAC_DT_PERID(29))>;
> +			dma-names = "tx", "rx";
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 47>;
> +			clock-names = "usart";
> +			status = "disabled";
> +		};
> +
> +		pinctrl: pinctrl at fffff400 {
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			compatible = "microchip,sam9x60-pinctrl", "atmel,at91sam9x5-pinctrl", "simple-mfd";
> +			ranges = <0xfffff400 0xfffff400 0x800>;
> +
> +			/* mux-mask corresponding to sam9x7 SoC in TFBGA228L package */
> +			atmel,mux-mask = <
> +					 /*  A		B	   C	      D	  */
> +					 0xffffffff 0xffffefc0 0xc0ffd000 0x00000000	/* pioA */
> +					 0x07ffffff 0x0805fe7f 0x01ff9f80 0x06078000	/* pioB */
> +					 0xffffffff 0x07dfffff 0xfa3fffff 0x00000000	/* pioC */
> +					 0x00003fff 0x00003fe0 0x0000003f 0x00000000	/* pioD */
> +					 >;
> +
> +			pioA: gpio at fffff400 {
> +				compatible = "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
> +				reg = <0xfffff400 0x200>;
> +				interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
> +				#gpio-cells = <2>;
> +				gpio-controller;
> +				interrupt-controller;
> +				#interrupt-cells = <2>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 2>;
> +			};
> +
> +			pioB: gpio at fffff600 {
> +				compatible = "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
> +				reg = <0xfffff600 0x200>;
> +				interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
> +				#gpio-cells = <2>;
> +				gpio-controller;
> +				#gpio-lines = <26>;
> +				interrupt-controller;
> +				#interrupt-cells = <2>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 3>;
> +			};
> +
> +			pioC: gpio at fffff800 {
> +				compatible = "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
> +				reg = <0xfffff800 0x200>;
> +				interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
> +				#gpio-cells = <2>;
> +				gpio-controller;
> +				interrupt-controller;
> +				#interrupt-cells = <2>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 4>;
> +			};
> +
> +			pioD: gpio at fffffa00 {
> +				compatible = "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
> +				reg = <0xfffffa00 0x200>;
> +				interrupts = <44 IRQ_TYPE_LEVEL_HIGH 1>;
> +				#gpio-cells = <2>;
> +				gpio-controller;
> +				#gpio-lines = <22>;
> +				interrupt-controller;
> +				#interrupt-cells = <2>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 44>;
> +			};
> +		};
> +
> +		pmc: pmc at fffffc00 {
> +			compatible = "microchip,sam9x7-pmc", "syscon";
> +			reg = <0xfffffc00 0x200>;
> +			interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
> +			#clock-cells = <2>;
> +			clocks = <&clk32k 1>, <&clk32k 0>, <&main_xtal>;
> +			clock-names = "td_slck", "md_slck", "main_xtal";
> +		};
> +
> +		reset_controller: rstc at fffffe00 {
> +			compatible = "microchip,sam9x60-rstc";
> +			reg = <0xfffffe00 0x10>;
> +			clocks = <&clk32k 0>;
> +		};
> +
> +		shutdown_controller: shdwc at fffffe10 {
> +			compatible = "microchip,sam9x60-shdwc";
> +			reg = <0xfffffe10 0x10>;
> +			clocks = <&clk32k 0>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			atmel,wakeup-rtc-timer;
> +			atmel,wakeup-rtt-timer;
> +			status = "disabled";
> +		};
> +
> +		rtt: rtc at fffffe20 {
> +			compatible = "microchip,sam9x60-rtt", "atmel,at91sam9260-rtt";
> +			reg = <0xfffffe20 0x20>;
> +			interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
> +			clocks = <&clk32k 0>;
> +		};
> +
> +		clk32k: sckc at fffffe50 {
> +			compatible = "microchip,sam9x60-sckc";
> +			reg = <0xfffffe50 0x4>;
> +			clocks = <&slow_xtal>;
> +			#clock-cells = <1>;
> +		};
> +
> +		gpbr: syscon at fffffe60 {
> +			compatible = "microchip,sam9x60-gpbr", "atmel,at91sam9260-gpbr", "syscon";
> +			reg = <0xfffffe60 0x10>;
> +		};
> +
> +		rtc: rtc at fffffea8 {
> +			compatible = "microchip,sam9x60-rtc";
> +			reg = <0xfffffea8 0x100>;
> +			interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
> +			clocks = <&clk32k 0>;
> +		};
> +
> +		watchdog: watchdog at ffffff80 {
> +			compatible = "microchip,sam9x60-wdt";
> +			reg = <0xffffff80 0x24>;
> +			interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
> +			clocks = <&clk32k 0>;
> +			status = "disabled";
> +		};
> +	};
> +};

-- 
With Best Regards,
Dharma B.



More information about the linux-arm-kernel mailing list