[RFC PATCH 5/5] ARM: dts: stm32: Add Octavo OSD32MP1-RED board

[Alexandre TORGUE]

On 6/6/23 16:55, Sean Nyekjaer wrote:
> Add support for the Octavo OSD32MP1-RED development board.
> 
> General features:
>   - STM32MP157C
>   - 512MB DDR3
>   - CAN-FD
>   - HDMI
>   - USB-C OTG
>   - UART
> 
> Signed-off-by: Sean Nyekjaer <sean at geanix.com>
> ---
> 
> This is made with great inspiration from Neeraj Dantu's work:
> https://raw.githubusercontent.com/octavosystems/OSD32MP1-RED-Device-tree/main/linux-v5.10-r0/stm32mp157c-osd32mp1-red.dts
> 
> So what copyright is needed here?
> And author?

hum maybe Rob, or Krzystof will have a better answer than me but I would 
say that only your name is enough. It's boards descriptions based on 
common binding so at the end if 2 boards are quite similar their DT will 
be similar. Not sure, but adding Neeraj as author could impose to him a 
kind of responsibility to this file, and you have to check this point 
with him if plan to add him.

Alex

> 
> Still need to test ethernet and HDMI, thats why I have done this a RFC.
> 
>   .../arm/boot/dts/stm32mp157c-osd32mp1-red.dts | 186 ++++++++++++++++++
>   1 file changed, 186 insertions(+)
>   create mode 100644 arch/arm/boot/dts/stm32mp157c-osd32mp1-red.dts
> 
> diff --git a/arch/arm/boot/dts/stm32mp157c-osd32mp1-red.dts b/arch/arm/boot/dts/stm32mp157c-osd32mp1-red.dts
> new file mode 100644
> index 000000000000..dd4e2668878c
> --- /dev/null
> +++ b/arch/arm/boot/dts/stm32mp157c-osd32mp1-red.dts
> @@ -0,0 +1,186 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> +/*
> + * Copyright (C) ?? - All Rights Reserved
> + * Author: ???
> + */
> +
> +/dts-v1/;
> +
> +#include "stm32mp157.dtsi"
> +#include "stm32mp15xc.dtsi"
> +#include "stm32mp15xx-osd32mp1.dtsi"
> +
> +/ {
> +	model = "Octavo OSD32MP1 RED board";
> +	compatible = "octavo,stm32mp157c-osd32mp1-red", "st,stm32mp157";
> +
> +	aliases {
> +		serial0 = &uart4;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	memory at c0000000 {
> +		device_type = "memory";
> +		reg = <0xc0000000 0x20000000>;
> +	};
> +
> +	led {
> +		compatible = "gpio-leds";
> +
> +		blue {
> +			label = "heartbeat";
> +			gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "heartbeat";
> +			default-state = "off";
> +		};
> +	};
> +};
> +
> +&ethernet0 {
> +	status = "okay";
> +	pinctrl-0 = <&ethernet0_rgmii_pins_a>;
> +	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_a>;
> +	pinctrl-names = "default", "sleep";
> +	phy-mode = "rgmii-id";
> +	max-speed = <1000>;
> +	phy-handle = <&phy0>;
> +	st,eth-clk-sel;
> +
> +	mdio0 {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		compatible = "snps,dwmac-mdio";
> +		phy0: ethernet-phy at 0 {
> +			reg = <3>;
> +		};
> +	};
> +};
> +
> +
> +&i2s2{
> +	clocks = <&rcc SPI2>, <&rcc SPI2_K>, <&rcc CK_PER>, <&rcc PLL3_R>;
> +	clock-names = "pclk", "i2sclk", "x8k", "x11k";
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&i2s2_pins_b>;
> +	pinctrl-1 = <&i2s2_sleep_pins_b>;
> +	status = "okay";
> +
> +	i2s2_port: port {
> +		i2s2_endpoint: endpoint {
> +			remote-endpoint = <&sii9022_tx_endpoint>;
> +			format = "i2s";
> +			mclk-fs = <256>;
> +		};
> +	};
> +};
> +
> +&iwdg2 {
> +	timeout-sec = <32>;
> +	status = "okay";
> +};
> +
> +&ltdc{
> +	status = "okay";
> +
> +	port {
> +		ltdc_ep0_out: endpoint at 0 {
> +			reg = <0>;
> +			remote-endpoint = <&sii9022_in>;
> +		};
> +	};
> +};
> +
> +&i2c1{
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&i2c1_pins_a>;
> +	pinctrl-1 = <&i2c1_sleep_pins_a>;
> +	status = "okay";
> +	i2c-scl-rising-time-ns = <100>;
> +	i2c-scl-falling-time-ns = <7>;
> +	/delete-property/dmas;
> +	/delete-property/dma-names;
> +
> +	hdmi-transmitter at 39 {
> +		compatible = "sil,sii9022";
> +		reg = <0x39>;
> +		reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>;
> +		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
> +		interrupt-parent = <&gpiog>;
> +		pinctrl-names = "default", "sleep";
> +		pinctrl-0 = <&ltdc_pins_e>;
> +		pinctrl-1 = <&ltdc_sleep_pins_e>;
> +		status = "okay";
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port at 0 {
> +				reg = <0>;
> +				sii9022_in: endpoint {
> +					remote-endpoint = <&ltdc_ep0_out>;
> +				};
> +			};
> +
> +			port at 1 {
> +				reg = <1>;
> +				sii9022_tx_endpoint: endpoint {
> +					remote-endpoint = <&i2s2_endpoint>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&tamp {
> +	status = "okay";
> +};
> +
> +&sdmmc1 {
> +	pinctrl-names = "default", "opendrain", "sleep";
> +	pinctrl-0 = <&sdmmc1_b4_pins_a>;
> +	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
> +	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
> +	cd-gpios = <&gpioe 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> +	disable-wp;
> +	st,neg-edge;
> +	bus-width = <4>;
> +	vmmc-supply = <&v3v3>;
> +	status = "okay";
> +};
> +
> +&sdmmc2 {
> +	pinctrl-names = "default", "opendrain", "sleep";
> +	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_d>;
> +	pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
> +	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_d>;
> +	non-removable;
> +	no-sd;
> +	no-sdio;
> +	st,neg-edge;
> +	bus-width = <8>;
> +	vmmc-supply = <&v3v3>;
> +	vqmmc-supply = <&vdd>;
> +	mmc-ddr-3_3v;
> +	status = "okay";
> +};
> +
> +&uart4 {
> +	pinctrl-names = "default", "sleep", "idle";
> +	pinctrl-0 = <&uart4_pins_a>;
> +	pinctrl-1 = <&uart4_sleep_pins_a>;
> +	pinctrl-2 = <&uart4_idle_pins_a>;
> +	/delete-property/dmas;
> +	/delete-property/dma-names;
> +	status = "okay";
> +};
> +
> +&m_can1 {
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&m_can1_pins_d>;
> +	pinctrl-1 = <&m_can1_sleep_pins_d>;
> +	status = "okay";
> +};