[EXTERNAL] Re: [PATCH] remoteproc: pru: add support for configuring GPMUX based on client setup

[Md Danish Anwar]

Hi Mathieu,

On 05/06/23 10:56 pm, Mathieu Poirier wrote:
> Hi MD,
> 
> On Thu, Jun 01, 2023 at 04:29:04PM +0530, MD Danish Anwar wrote:
>> From: Tero Kristo <t-kristo at ti.com>
>>
>> Client device node property ti,pruss-gp-mux-sel can now be used to
>> configure the GPMUX config value for PRU.
>>
>> Signed-off-by: Tero Kristo <t-kristo at ti.com>
>> Signed-off-by: Suman Anna <s-anna at ti.com>
>> Signed-off-by: MD Danish Anwar <danishanwar at ti.com>
>> ---
>>  drivers/remoteproc/pru_rproc.c | 21 +++++++++++++++++++++
>>  1 file changed, 21 insertions(+)
>>
>> diff --git a/drivers/remoteproc/pru_rproc.c b/drivers/remoteproc/pru_rproc.c
>> index 2874c8d324f7..29d3a5a930c1 100644
>> --- a/drivers/remoteproc/pru_rproc.c
>> +++ b/drivers/remoteproc/pru_rproc.c
>> @@ -109,6 +109,7 @@ struct pru_private_data {
>>   * @dbg_single_step: debug state variable to set PRU into single step mode
>>   * @dbg_continuous: debug state variable to restore PRU execution mode
>>   * @evt_count: number of mapped events
>> + * @gpmux_save: saved value for gpmux config
>>   */
>>  struct pru_rproc {
>>  	int id;
>> @@ -127,6 +128,7 @@ struct pru_rproc {
>>  	u32 dbg_single_step;
>>  	u32 dbg_continuous;
>>  	u8 evt_count;
>> +	u8 gpmux_save;
>>  };
>>  
>>  static inline u32 pru_control_read_reg(struct pru_rproc *pru, unsigned int reg)
>> @@ -228,6 +230,7 @@ struct rproc *pru_rproc_get(struct device_node *np, int index,
>>  	struct device *dev;
>>  	const char *fw_name;
>>  	int ret;
>> +	u32 mux;
>>  
>>  	rproc = __pru_rproc_get(np, index);
>>  	if (IS_ERR(rproc))
>> @@ -252,6 +255,22 @@ struct rproc *pru_rproc_get(struct device_node *np, int index,
>>  	if (pru_id)
>>  		*pru_id = pru->id;
>>  
>> +	ret = pruss_cfg_get_gpmux(pru->pruss, pru->id, &pru->gpmux_save);
>> +	if (ret) {
>> +		dev_err(dev, "failed to get cfg gpmux: %d\n", ret);
>> +		goto err;
>> +	}
>> +
>> +	ret = of_property_read_u32_index(np, "ti,pruss-gp-mux-sel", index,
>> +					 &mux);
>> +	if (!ret) {
>> +		ret = pruss_cfg_set_gpmux(pru->pruss, pru->id, mux);
>> +		if (ret) {
>> +			dev_err(dev, "failed to set cfg gpmux: %d\n", ret);
>> +			goto err;
>> +		}
>> +	}
>> +
> 
> It would have been nice to be told in a cover letter that pruss_cfg_get_gpmux()
> is in linux-next so that I don't have to go fish for it...
> 

My bad, I should have mentioned it. This patch depends on the soc: ti: pruss
series [1] which is merged to Nishant's tree and is part of 'linux-next' but
this isn't yet part of mainline linux.

> I am fine with the code in this patch, though the changelog is cryptic and could
> be enhanced to say "why" this is needed.  The above could use some comments to
> make sure people looking at this code understand that an error from
> of_property_read_u32_index() is acceptable for backward compatibility.
> 
> Here I have to suppose pruss_cfg_get_gpmux() has been added to Nishanth's tree.
> As such the only way for me to apply your patch is if Nishanth sends me a pull
> request for the patchset that introduced pruss_cfg_get_gpmux().  You can also
> resend this in the next cycle.

I will fix the changelog and send the next revision in the next cycle.

> 
> Thanks,
> Mathieu
> 

[1] https://lore.kernel.org/all/20230414045542.3249939-1-danishanwar@ti.com/

-- 
Thanks and Regards,
Danish.