[PATCH v2 1/6] arm64: zynqmp: Describe TI phy as ethernet-phy-id
Michal Simek
monstr at monstr.eu
Mon Jun 5 04:15:36 PDT 2023
On 5/22/23 16:59, Michal Simek wrote:
> TI DP83867 is using strapping based on MIO pins. Tristate setup can
> influence PHY address. That's why switch description with ethernet-phy-id
> compatible string which enable calling reset. PHY itself setups phy address
> after power up or reset. Phy reset is done via gpio.
>
> Signed-off-by: Michal Simek <michal.simek at amd.com>
> ---
>
> Changes in v2:
> - fix typo in commit message
>
> Checkpatch is reporting issue
> warning: DT compatible string "ethernet-phy-id2000.a231" appears un-documented
> but it should be fully aligned with
> Documentation/devicetree/bindings/net/ethernet-phy.yaml
>
> c&p more details from v1 version:
> Phy has some pins which is using for strapping for phy address after phy
> reset or power on. Pretty much it is resistor array which based on
> datasheet is decoded to certain phy address.
> And because some phy pins are also used as data pin for RGMII they are
> connected via MIO pins on a silicon. That's why IO block output setting
> really matter here because it changes resistor array and it moves phy
> address.
> That's why there is a need to do proper IO pin setup and after it call phy
> reset to get it to address which was decided by PCB designer.
>
> ---
> .../boot/dts/xilinx/zynqmp-zcu102-revA.dts | 23 +++++++++++------
> .../boot/dts/xilinx/zynqmp-zcu102-revB.dts | 25 +++++++++++--------
> .../boot/dts/xilinx/zynqmp-zcu104-revA.dts | 22 ++++++++++------
> .../boot/dts/xilinx/zynqmp-zcu104-revC.dts | 22 ++++++++++------
> .../boot/dts/xilinx/zynqmp-zcu106-revA.dts | 22 ++++++++++------
> .../boot/dts/xilinx/zynqmp-zcu111-revA.dts | 22 ++++++++++------
> 6 files changed, 90 insertions(+), 46 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
> index 230ef94d5dcb..f36353a51863 100644
> --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
> +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
> @@ -2,7 +2,8 @@
> /*
> * dts file for Xilinx ZynqMP ZCU102 RevA
> *
> - * (C) Copyright 2015 - 2021, Xilinx, Inc.
> + * (C) Copyright 2015 - 2022, Xilinx, Inc.
> + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
> *
> * Michal Simek <michal.simek at amd.com>
> */
> @@ -200,13 +201,19 @@ &gem3 {
> phy-mode = "rgmii-id";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_gem3_default>;
> - phy0: ethernet-phy at 21 {
> - reg = <21>;
> - ti,rx-internal-delay = <0x8>;
> - ti,tx-internal-delay = <0xa>;
> - ti,fifo-depth = <0x1>;
> - ti,dp83867-rxctrl-strap-quirk;
> - /* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */
> + mdio: mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy0: ethernet-phy at 21 {
> + #phy-cells = <1>;
> + compatible = "ethernet-phy-id2000.a231";
> + reg = <21>;
> + ti,rx-internal-delay = <0x8>;
> + ti,tx-internal-delay = <0xa>;
> + ti,fifo-depth = <0x1>;
> + ti,dp83867-rxctrl-strap-quirk;
> + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
> + };
> };
> };
>
> diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
> index 63419deb5b33..3c28130909bc 100644
> --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
> +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
> @@ -2,7 +2,8 @@
> /*
> * dts file for Xilinx ZynqMP ZCU102 RevB
> *
> - * (C) Copyright 2016 - 2021, Xilinx, Inc.
> + * (C) Copyright 2016 - 2022, Xilinx, Inc.
> + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
> *
> * Michal Simek <michal.simek at amd.com>
> */
> @@ -16,16 +17,20 @@ / {
>
> &gem3 {
> phy-handle = <&phyc>;
> - phyc: ethernet-phy at c {
> - reg = <0xc>;
> - ti,rx-internal-delay = <0x8>;
> - ti,tx-internal-delay = <0xa>;
> - ti,fifo-depth = <0x1>;
> - ti,dp83867-rxctrl-strap-quirk;
> - /* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */
> + mdio: mdio {
> + phyc: ethernet-phy at c {
> + #phy-cells = <0x1>;
> + compatible = "ethernet-phy-id2000.a231";
> + reg = <0xc>;
> + ti,rx-internal-delay = <0x8>;
> + ti,tx-internal-delay = <0xa>;
> + ti,fifo-depth = <0x1>;
> + ti,dp83867-rxctrl-strap-quirk;
> + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
> + };
> + /* Cleanup from RevA */
> + /delete-node/ ethernet-phy at 21;
> };
> - /* Cleanup from RevA */
> - /delete-node/ ethernet-phy at 21;
> };
>
> /* Fix collision with u61 */
> diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
> index d178a4f898c9..3fd47725c2c8 100644
> --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
> +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
> @@ -2,7 +2,8 @@
> /*
> * dts file for Xilinx ZynqMP ZCU104
> *
> - * (C) Copyright 2017 - 2021, Xilinx, Inc.
> + * (C) Copyright 2017 - 2022, Xilinx, Inc.
> + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
> *
> * Michal Simek <michal.simek at amd.com>
> */
> @@ -109,12 +110,19 @@ &gem3 {
> phy-mode = "rgmii-id";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_gem3_default>;
> - phy0: ethernet-phy at c {
> - reg = <0xc>;
> - ti,rx-internal-delay = <0x8>;
> - ti,tx-internal-delay = <0xa>;
> - ti,fifo-depth = <0x1>;
> - ti,dp83867-rxctrl-strap-quirk;
> + mdio: mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy0: ethernet-phy at c {
> + #phy-cells = <1>;
> + compatible = "ethernet-phy-id2000.a231";
> + reg = <0xc>;
> + ti,rx-internal-delay = <0x8>;
> + ti,tx-internal-delay = <0xa>;
> + ti,fifo-depth = <0x1>;
> + ti,dp83867-rxctrl-strap-quirk;
> + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
> + };
> };
> };
>
> diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
> index 38b11594c074..4f6429caecff 100644
> --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
> +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
> @@ -2,7 +2,8 @@
> /*
> * dts file for Xilinx ZynqMP ZCU104
> *
> - * (C) Copyright 2017 - 2021, Xilinx, Inc.
> + * (C) Copyright 2017 - 2022, Xilinx, Inc.
> + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
> *
> * Michal Simek <michal.simek at amd.com>
> */
> @@ -114,12 +115,19 @@ &gem3 {
> phy-mode = "rgmii-id";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_gem3_default>;
> - phy0: ethernet-phy at c {
> - reg = <0xc>;
> - ti,rx-internal-delay = <0x8>;
> - ti,tx-internal-delay = <0xa>;
> - ti,fifo-depth = <0x1>;
> - ti,dp83867-rxctrl-strap-quirk;
> + mdio: mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy0: ethernet-phy at c {
> + #phy-cells = <1>;
> + compatible = "ethernet-phy-id2000.a231";
> + reg = <0xc>;
> + ti,rx-internal-delay = <0x8>;
> + ti,tx-internal-delay = <0xa>;
> + ti,fifo-depth = <0x1>;
> + ti,dp83867-rxctrl-strap-quirk;
> + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
> + };
> };
> };
>
> diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
> index 8af0879806cf..8c3fa3fe28d5 100644
> --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
> +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
> @@ -2,7 +2,8 @@
> /*
> * dts file for Xilinx ZynqMP ZCU106
> *
> - * (C) Copyright 2016 - 2021, Xilinx, Inc.
> + * (C) Copyright 2016 - 2022, Xilinx, Inc.
> + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
> *
> * Michal Simek <michal.simek at amd.com>
> */
> @@ -212,12 +213,19 @@ &gem3 {
> phy-mode = "rgmii-id";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_gem3_default>;
> - phy0: ethernet-phy at c {
> - reg = <0xc>;
> - ti,rx-internal-delay = <0x8>;
> - ti,tx-internal-delay = <0xa>;
> - ti,fifo-depth = <0x1>;
> - ti,dp83867-rxctrl-strap-quirk;
> + mdio: mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy0: ethernet-phy at c {
> + #phy-cells = <1>;
> + reg = <0xc>;
> + compatible = "ethernet-phy-id2000.a231";
> + ti,rx-internal-delay = <0x8>;
> + ti,tx-internal-delay = <0xa>;
> + ti,fifo-depth = <0x1>;
> + ti,dp83867-rxctrl-strap-quirk;
> + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
> + };
> };
> };
>
> diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
> index f76687914e30..0d9b6081dff6 100644
> --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
> +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
> @@ -2,7 +2,8 @@
> /*
> * dts file for Xilinx ZynqMP ZCU111
> *
> - * (C) Copyright 2017 - 2021, Xilinx, Inc.
> + * (C) Copyright 2017 - 2022, Xilinx, Inc.
> + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
> *
> * Michal Simek <michal.simek at amd.com>
> */
> @@ -172,12 +173,19 @@ &gem3 {
> phy-mode = "rgmii-id";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_gem3_default>;
> - phy0: ethernet-phy at c {
> - reg = <0xc>;
> - ti,rx-internal-delay = <0x8>;
> - ti,tx-internal-delay = <0xa>;
> - ti,fifo-depth = <0x1>;
> - ti,dp83867-rxctrl-strap-quirk;
> + mdio: mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy0: ethernet-phy at c {
> + #phy-cells = <1>;
> + compatible = "ethernet-phy-id2000.a231";
> + reg = <0xc>;
> + ti,rx-internal-delay = <0x8>;
> + ti,tx-internal-delay = <0xa>;
> + ti,fifo-depth = <0x1>;
> + ti,dp83867-rxctrl-strap-quirk;
> + reset-gpios = <&tca6416_u22 6 GPIO_ACTIVE_LOW>;
> + };
> };
> };
>
Applied.
M
--
Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91
w: www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel - Xilinx Microblaze
Maintainer of Linux kernel - Xilinx Zynq ARM and ZynqMP/Versal ARM64 SoCs
U-Boot custodian - Xilinx Microblaze/Zynq/ZynqMP/Versal/Versal NET SoCs
TF-A maintainer - Xilinx ZynqMP/Versal/Versal NET SoCs
More information about the linux-arm-kernel
mailing list