[PATCH 7/8] arm64: dts: ti: k3-am69-sk: Enable wakeup_i2c0 and eeprom

Nishanth Menon nm at ti.com
Fri Jun 2 14:49:36 PDT 2023


Enable wakeup_i2c and use un-used pinmux. While at it, describe the
board detection eeprom present on the board.

Signed-off-by: Nishanth Menon <nm at ti.com>
---
Depends on https://lore.kernel.org/linux-arm-kernel/20230503083143.32369-1-t-konduru@ti.com/

 arch/arm64/boot/dts/ti/k3-am69-sk.dts | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
index 409fcbaf0126..a0e7872f31f2 100644
--- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
@@ -25,6 +25,7 @@ aliases {
 		serial1 = &mcu_uart0;
 		serial2 = &main_uart8;
 		mmc1 = &main_sdhci1;
+		i2c0 = &wkup_i2c0;
 		i2c3 = &main_i2c0;
 		ethernet0 = &mcu_cpsw_port1;
 	};
@@ -152,6 +153,13 @@ J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (K34) WKUP_UART0_TXD */
 		>;
 	};
 
+	wkup_i2c0_pins_default: wkup-i2c0-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x98, PIN_INPUT, 0) /* (N33) WKUP_I2C0_SCL */
+			J721S2_WKUP_IOPAD(0x9c, PIN_INPUT, 0) /* (N35) WKUP_I2C0_SDA */
+		>;
+	};
+
 	mcu_uart0_pins_default: mcu-uart0-pins-default {
 		pinctrl-single,pins = <
 			J784S4_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (K38) WKUP_GPIO0_13.MCU_UART0_RXD */
@@ -191,6 +199,19 @@ &wkup_uart0 {
 	pinctrl-0 = <&wkup_uart0_pins_default>;
 };
 
+&wkup_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&wkup_i2c0_pins_default>;
+	clock-frequency = <400000>;
+
+	eeprom at 51 {
+		/* AT24C512C-MAHM-T */
+		compatible = "atmel,24c512";
+		reg = <0x51>;
+	};
+};
+
 &mcu_uart0 {
 	status = "okay";
 	pinctrl-names = "default";
-- 
2.40.0




More information about the linux-arm-kernel mailing list