[PATCH 1/2] dt-bindings: phy: mxs-usb-phy: convert to DT schema format

[Krzysztof Kozlowski]

On 01/06/2023 10:07, Xu Yang wrote:
> Convert the binding to DT schema format.
> 


Thank you for your patch. There is something to discuss/improve.


e/bindings/phy/mxs-usb-phy.yaml
b/Documentation/devicetree/bindings/phy/mxs-usb-phy.yaml
> new file mode 100644
> index 000000000000..48b0e654e52c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/mxs-usb-phy.yaml

Filename matching compatibles, so for exmaple fsl,mxs-usbphy.yaml.

> @@ -0,0 +1,97 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/phy/mxs-usb-phy.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Freescale MXS USB Phy Device
> +
> +maintainers:
> +  - Xu Yang <xu.yang_2 at nxp.com>
> +
> +properties:
> +  compatible:
> +    oneOf:
> +      - enum:
> +          - fsl,imx23-usbphy
> +          - fsl,vf610-usbphy
> +      - items:
> +          - enum:
> +              - fsl,imx28-usbphy
> +              - fsl,imx6ul-usbphy
> +              - fsl,imx6sl-usbphy
> +              - fsl,imx6sx-usbphy
> +              - fsl,imx6q-usbphy
> +          - const: fsl,imx23-usbphy
> +      - items:
> +          - enum:
> +              - fsl,imx7ulp-usbphy
> +              - fsl,imx6sll-usbphy
> +          - const: fsl,imx6ul-usbphy
> +          - const: fsl,imx23-usbphy
> +      - items:
> +          - const: fsl,imx8dxl-usbphy
> +          - const: fsl,imx7ulp-usbphy
> +          - const: fsl,imx6ul-usbphy
> +          - const: fsl,imx23-usbphy

I cannot find these in the old bindings. Please explain changes to
conversion in commit msg. So far you wrote that it is pure conversion.

> +
> +  reg:
> +    minItems: 1
> +    maxItems: 2
> +
> +  interrupts:
> +    minItems: 1
> +    maxItems: 2
> +
> +  fsl,anatop:
> +    description:
> +      phandle for anatop register, it is only for imx6 SoC series
> +    $ref: /schemas/types.yaml#/definitions/phandle-array
> +    maxItems: 1
> +
> +  fsl,tx-cal-45-dn-ohms:
> +    description:
> +      Resistance (in ohms) of switchable high-speed trimming resistor
> +      connected in parallel with the 45 ohm resistor that terminates
> +      the DN output signal.
> +    minimum: 35
> +    maximum: 54
> +    default: 45
> +
> +  fsl,tx-cal-45-dp-ohms:
> +    description:
> +      Resistance (in ohms) of switchable high-speed trimming resistor
> +      connected in parallel with the 45 ohm resistor that terminates
> +      the DP output signal.
> +    minimum: 35
> +    maximum: 54
> +    default: 45
> +
> +  fsl,tx-d-cal:
> +    description:
> +      Current trimming value (as a percentage) of the 17.78 mA TX
> +      reference current.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    minimum: 79
> +    maximum: 119
> +    default: 100
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +

missing allOf narrowing anatop to imx6. Also interrupts and reg should
be narrowed to respective variants.

> +unevaluatedProperties: false

Instead additionalProperties: false.

> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +    usbphy1: usb-phy at 20c9000 {
> +        compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy";
> +        reg = <0x020c9000 0x1000>;
> +        interrupts = <0 44 IRQ_TYPE_LEVEL_HIGH>;

Is 0 known flag? Use defines for it.

> +        fsl,anatop = <&anatop>;
> +    };
> +
> +...

Best regards,
Krzysztof