[PATCH v1 35/43] ARM: dts: add device tree for ep93xx Soc
Krzysztof Kozlowski
krzysztof.kozlowski at linaro.org
Thu Jun 1 01:30:28 PDT 2023
On 01/06/2023 07:45, Nikita Shubin wrote:
> This adds a divice for Cirrus ep93xx SoC amd ts7250 board that has been
device
> my testing target for ep93xx device support.
>
> Also inluded device tree for Liebherr BK3.1 board through it's not a
included
> complete support.
Thank you for your patch. There is something to discuss/improve.
>
> Signed-off-by: Nikita Shubin <nikita.shubin at maquefel.me>
> ---
>
> Notes:
> v0 -> v1:
>
> - add empty chosen node
> - s/dallas,rtc-m48t86/st,m48t86/
> - changed phy_id to phy-handle
> - dropped gpio chip-label's
> - s/eth at 80010000/ethernet at 80010000
> - s/use_dma/ep9301,use-dma
> - added i2s to bk3
>
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/ep93xx-bk3.dts | 119 +++++++
> arch/arm/boot/dts/ep93xx-ts7250.dts | 132 ++++++++
> arch/arm/boot/dts/ep93xx.dtsi | 466 ++++++++++++++++++++++++++++
Split adding DTSI from adding boards.
> 4 files changed, 718 insertions(+)
> create mode 100644 arch/arm/boot/dts/ep93xx-bk3.dts
> create mode 100644 arch/arm/boot/dts/ep93xx-ts7250.dts
> create mode 100644 arch/arm/boot/dts/ep93xx.dtsi
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 59829fc90315..a68f868fffe7 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1670,3 +1670,4 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
> aspeed-bmc-vegman-n110.dtb \
> aspeed-bmc-vegman-rx20.dtb \
> aspeed-bmc-vegman-sx20.dtb
> +dtb-$(CONFIG_ARCH_EP93XX) += ep93xx-ts7250.dtb
> diff --git a/arch/arm/boot/dts/ep93xx-bk3.dts b/arch/arm/boot/dts/ep93xx-bk3.dts
> new file mode 100644
> index 000000000000..215587c498e6
> --- /dev/null
> +++ b/arch/arm/boot/dts/ep93xx-bk3.dts
> @@ -0,0 +1,119 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Device Tree file for Liebherr controller BK3.1 based on Cirrus EP9302 SoC
> + */
> +/dts-v1/;
> +#include "ep93xx.dtsi"
> +
> +/ {
> + model = "Liebherr controller BK3.1";
> + compatible = "liebherr,bk3", "cirrus,ep9301";
> +
> + chosen {
> + };
> +
> + memory {
> + device_type = "memory";
> + };
> +
> + soc {
> + nand-controller at 60000000 {
Override/extend by label/phandle.
> + compatible = "technologic,ts7200-nand";
> + reg = <0x60000000 0x8000000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition at 0 {
> + label = "System";
> + reg = <0x00000000 0x01e00000>;
> + read-only;
> + };
> +
> + partition at 1e00000 {
> + label = "Data";
> + reg = <0x01e00000 0x05f20000>;
> + };
> +
> + partition at 7d20000 {
> + label = "RedBoot";
> + reg = <0x07d20000 0x002e0000>;
> + read-only;
> + };
> + };
> + };
> +
> + syscon: syscon at 80930000 {
Override/extend by label/phandle.
> + pinctrl: pinctrl {
> + compatible = "cirrus,ep9301-pinctrl";
Why this is board specific?
> + };
> + };
> +
> + gpio1: gpio at 80840004 {
Override/extend by label/phandle.
> + /* PWM */
> + gpio-ranges = <&pinctrl 6 163 1>;
> + };
> + };
> +};
> +
> +&gpio1 {
> + /* PWM */
> + gpio-ranges = <&pinctrl 6 163 1>;
> +};
> +
> +&gpio4 {
> + gpio-ranges = <&pinctrl 0 97 2>;
> + status = "okay";
> +};
> +
> +&gpio6 {
> + gpio-ranges = <&pinctrl 0 87 2>;
> + status = "okay";
> +};
> +
> +&gpio7 {
> + gpio-ranges = <&pinctrl 2 199 4>;
> + status = "okay";
> +};
> +
> +&i2c {
> + status = "okay";
> +};
> +
> +&spi0: spi at 808a0000 {
> + cs-gpios = <&gpio5 3 0>;
Use proper defines for flags.
> + status = "okay";
What's here? Empty enabled bus?
> +};
> +
> +ð0 {
> + phy-handle = <&phy0>;
> +};
> +
> +&mdio0 {
> + phy0: ethernet-phy at 1 {
> + reg = <1>;
> + device_type = "ethernet-phy";
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&usb {
> + status = "okay";
> +};
> +
> +&i2s {
Up to you, but I seriously recommend keeping all labels ordered by name.
Avoids conflicts.
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2s_on_ac97_pins>;
> + /delete-property/ status;
??? I don't understand. Why would you do this?
...
> diff --git a/arch/arm/boot/dts/ep93xx.dtsi b/arch/arm/boot/dts/ep93xx.dtsi
> new file mode 100644
> index 000000000000..6da556ceaf04
> --- /dev/null
> +++ b/arch/arm/boot/dts/ep93xx.dtsi
> @@ -0,0 +1,466 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Device Tree file for Cirrus Logic systems EP93XX SoC
> + */
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/clock/cirrus,ep93xx-clock.h>
> +/ {
> + soc {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> + compatible = "simple-bus";
> +
> + syscon: syscon at 80930000 {
> + compatible = "cirrus,ep9301-syscon",
> + "syscon", "simple-mfd";
Broken wrapping. Align these with previous ".
> + reg = <0x80930000 0x1000>;
> +
> + ep9301-reboot {
Just "reboot" (and fix bindings)... but why would you need it in the
first place? I think something is seriously missing in your bindings.
> + compatible = "cirrus,ep9301-reboot";
> + };
> +
> + eclk: clock-controller {
> + #clock-cells = <1>;
> + compatible = "cirrus,ep9301-clk";
> + status = "okay";
> + clocks = <&xtali>;
> + };
> +
> + pinctrl: pinctrl {
Missing compatible.
> + spi_default_pins: pins-spi {
> + function = "spi";
> + groups = "ssp";
> + };
> +
> + ac97_default_pins: pins-ac97 {
> + function = "ac97";
> + groups = "ac97";
> + };
> +
> + i2s_on_ssp_pins: pins-i2sonssp {
> + function = "i2s";
> + groups = "i2s_on_ssp";
> + };
> +
> + i2s_on_ac97_pins: pins-i2sonac97 {
> + function = "i2s";
> + groups = "i2s_on_ac97";
> + };
> +
> + gpio1_default_pins: pins-gpio1 {
> + function = "gpio";
> + groups = "gpio1agrp";
> + };
> +
> + pwm1_default_pins: pins-pwm1 {
> + function = "pwm";
> + groups = "pwm1";
> + };
> +
> + gpio2_default_pins: pins-gpio2 {
> + function = "gpio";
> + groups = "gpio2agrp";
> + };
> +
> + gpio3_default_pins: pins-gpio3 {
> + function = "gpio";
> + groups = "gpio3agrp";
> + };
> +
> + keypad_default_pins: pins-keypad {
> + function = "keypad";
> + groups = "keypadgrp";
> + };
> +
> + gpio4_default_pins: pins-gpio4 {
> + function = "gpio";
> + groups = "gpio4agrp";
> + };
> +
> + gpio6_default_pins: pins-gpio6 {
> + function = "gpio";
> + groups = "gpio6agrp";
> + };
> +
> + gpio7_default_pins: pins-gpio7 {
> + function = "gpio";
> + groups = "gpio7agrp";
> + };
> +
> + ide_default_pins: pins-ide {
> + function = "pata";
> + groups = "idegrp";
> + };
> +
> + lcd_on_dram0_pins: pins-rasteronsdram0 {
> + function = "lcd";
> + groups = "rasteronsdram0grp";
> + };
> +
> + lcd_on_dram3_pins: pins-rasteronsdram3 {
> + function = "lcd";
> + groups = "rasteronsdram3grp";
I would expect somewhere two groups since you explicitly allow it.
> + };
> + };
> + };
> +
> + vic0: interrupt-controller at 800b0000 {
> + compatible = "arm,pl192-vic";
> + interrupt-controller;
> + reg = <0x800b0000 0x1000>;
compatible first, reg is second. ranges if present - third. Fix it
everywhere.
> + #interrupt-cells = <1>;
> + valid-mask = <0x7ffffffc>;
> + valid-wakeup-mask = <0x0>;
> + };
> +
> + vic1: interrupt-controller at 800c0000 {
> + compatible = "arm,pl192-vic";
> + interrupt-controller;
> + reg = <0x800c0000 0x1000>;
> + #interrupt-cells = <1>;
> + valid-mask = <0x1fffffff>;
> + valid-wakeup-mask = <0x0>;
> + };
> +
> + timer: timer at 80810000 {
> + compatible = "cirrus,ep9301-timer";
> + reg = <0x80810000 0x100>;
> + interrupt-parent = <&vic1>;
> + interrupts = <19>;
> + };
> +
> + dma0: dma-controller at 80000000 {
> + compatible = "cirrus,ep9301-dma-m2p";
> + reg = <0x80000000 0x0040>,
> + <0x80000040 0x0040>,
> + <0x80000080 0x0040>,
> + <0x800000c0 0x0040>,
> + <0x80000240 0x0040>,
> + <0x80000200 0x0040>,
> + <0x800002c0 0x0040>,
> + <0x80000280 0x0040>,
> + <0x80000340 0x0040>,
> + <0x80000300 0x0040>;
> + clocks = <&eclk EP93XX_CLK_M2P0>,
> + <&eclk EP93XX_CLK_M2P1>,
> + <&eclk EP93XX_CLK_M2P2>,
> + <&eclk EP93XX_CLK_M2P3>,
> + <&eclk EP93XX_CLK_M2P4>,
> + <&eclk EP93XX_CLK_M2P5>,
> + <&eclk EP93XX_CLK_M2P6>,
> + <&eclk EP93XX_CLK_M2P7>,
> + <&eclk EP93XX_CLK_M2P8>,
> + <&eclk EP93XX_CLK_M2P9>;
> + clock-names = "m2p0", "m2p1",
> + "m2p2", "m2p3",
> + "m2p4", "m2p5",
> + "m2p6", "m2p7",
> + "m2p8", "m2p9";
> + interrupt-parent = <&vic0>;
> + interrupts = <7>, <8>, <9>, <10>, <11>,
> + <12>, <13>, <14>, <15>, <16>;
> + #dma-cells = <1>;
> + };
> +
> + dma1: dma-controller at 80000100 {
> + compatible = "cirrus,ep9301-dma-m2m";
> + reg = <0x80000100 0x0040>,
> + <0x80000140 0x0040>;
> + clocks = <&eclk EP93XX_CLK_M2M0>,
> + <&eclk EP93XX_CLK_M2M1>;
> + clock-names = "m2m0", "m2m1";
> + interrupt-parent = <&vic0>;
> + interrupts = <17>, <18>;
> + #dma-cells = <1>;
> + };
> +
> + i2s: i2s at 80820000 {
> + compatible = "cirrus,ep9301-i2s";
> + #sound-dai-cells = <0>;
> + reg = <0x80820000 0x100>;
> + interrupt-parent = <&vic1>;
> + interrupts = <28>;
> + clocks = <&eclk EP93XX_CLK_I2S_MCLK
> + &eclk EP93XX_CLK_I2S_SCLK
> + &eclk EP93XX_CLK_I2S_LRCLK>;
> + clock-names = "mclk", "sclk", "lrclk";
> + status = "disabled";
> + };
> +
> + gpio0: gpio at 80840000 {
> + compatible = "cirrus,ep9301-gpio";
> + reg = <0x80840000 0x04>,
> + <0x80840010 0x04>,
> + <0x80840090 0x1c>;
Messed wrapping.
> + reg-names = "data", "dir", "intr";
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + interrupt-parent = <&vic1>;
> + interrupts = <27>;
> + };
> +
> + gpio1: gpio at 80840004 {
> + compatible = "cirrus,ep9301-gpio";
> + reg = <0x80840004 0x04>,
> + <0x80840014 0x04>,
> + <0x808400ac 0x1c>;
Ditto, in other places as well.
> + reg-names = "data", "dir", "intr";
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + interrupt-parent = <&vic1>;
> + interrupts = <27>;
> + };
> +
> + gpio2: gpio at 80840008 {
> + compatible = "cirrus,ep9301-gpio";
> + reg = <0x80840008 0x04>,
> + <0x80840018 0x04>;
> + reg-names = "data", "dir";
> + gpio-controller;
> + #gpio-cells = <2>;
> + status = "disabled";
Status is usually last.
> + pinctrl-names = "default";
> + pinctrl-0 = <&gpio2_default_pins>;
> + };
> +
> + gpio3: gpio at 8084000c {
> + compatible = "cirrus,ep9301-gpio";
> + reg = <0x8084000c 0x04>,
> + <0x8084001c 0x04>;
> + reg-names = "data", "dir";
> + gpio-controller;
> + #gpio-cells = <2>;
> + status = "disabled";
> + pinctrl-names = "default";
> + pinctrl-0 = <&gpio3_default_pins>;
> + };
> +
> + gpio4: gpio at 80840020 {
> + compatible = "cirrus,ep9301-gpio";
> + reg = <0x80840020 0x04>,
> + <0x80840024 0x04>;
> + reg-names = "data", "dir";
> + gpio-controller;
> + #gpio-cells = <2>;
> + status = "disabled";
> + pinctrl-names = "default";
> + pinctrl-0 = <&gpio4_default_pins>;
> + };
> +
> + gpio5: gpio at 80840030 {
> + compatible = "cirrus,ep9301-gpio";
> + reg = <0x80840030 0x04>,
> + <0x80840034 0x04>,
> + <0x8084004c 0x1c>;
> + reg-names = "data", "dir", "intr";
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + interrupts-extended = <&vic0 19>, <&vic0 20>,
> + <&vic0 21>, <&vic0 22>,
> + <&vic1 15>, <&vic1 16>,
> + <&vic1 17>, <&vic1 18>;
> + };
> +
> + gpio6: gpio at 80840038 {
> + compatible = "cirrus,ep9301-gpio";
> + reg = <0x80840038 0x04>,
> + <0x8084003c 0x04>;
> + reg-names = "data", "dir";
> + gpio-controller;
> + #gpio-cells = <2>;
> + status = "disabled";
> + pinctrl-names = "default";
> + pinctrl-0 = <&gpio6_default_pins>;
> + };
> +
> + gpio7: gpio at 80840040 {
> + compatible = "cirrus,ep9301-gpio";
> + reg = <0x80840040 0x04>,
> + <0x80840044 0x04>;
> + reg-names = "data", "dir";
> + gpio-controller;
> + #gpio-cells = <2>;
> + status = "disabled";
> + pinctrl-names = "default";
> + pinctrl-0 = <&gpio7_default_pins>;
> + };
> +
> + ide: ide at 800a0000 {
> + compatible = "cirrus,ep9312-pata";
> + reg = <0x800a0000 0x38>;
> + interrupt-parent = <&vic1>;
> + interrupts = <8>;
> + status = "disabled";
> + pinctrl-names = "default";
> + pinctrl-0 = <&ide_default_pins>;
> + };
> +
> + uart0: uart at 808c0000 {
This should scream with dtbs_check. serial.
It does not look like you tested the DTS against bindings. Please run
`make dtbs_check` (see
Documentation/devicetree/bindings/writing-schema.rst for instructions).
> + compatible = "arm,primecell";
> + reg = <0x808c0000 0x1000>;
> + arm,primecell-periphid = <0x00041010>;
> + clocks = <&eclk EP93XX_CLK_UART1>, <&eclk EP93XX_CLK_UART>;
> + clock-names = "apb:uart1", "apb_pclk";
> + interrupt-parent = <&vic1>;
> + interrupts = <20>;
> + status = "disabled";
> + };
> +
> + uart1: uart at 808d0000 {
> + compatible = "arm,primecell";
> + reg = <0x808d0000 0x1000>;
> + arm,primecell-periphid = <0x00041010>;
> + clocks = <&eclk EP93XX_CLK_UART2>, <&eclk EP93XX_CLK_UART>;
> + clock-names = "apb:uart2", "apb_pclk";
> + interrupt-parent = <&vic1>;
> + interrupts = <22>;
> + status = "disabled";
> + };
> +
> + uart2: uart at 808b0000 {
> + compatible = "arm,primecell";
> + reg = <0x808b0000 0x1000>;
> + arm,primecell-periphid = <0x00041010>;
> + clocks = <&eclk EP93XX_CLK_UART3>, <&eclk EP93XX_CLK_UART>;
> + clock-names = "apb:uart3", "apb_pclk";
> + interrupt-parent = <&vic1>;
> + interrupts = <23>;
> + status = "disabled";
> + };
> +
> + usb0: usb at 80020000 {
> + compatible = "generic-ohci";
> + reg = <0x80020000 0x10000>;
> + interrupt-parent = <&vic1>;
> + interrupts = <24>;
> + clocks = <&eclk EP93XX_CLK_USB>;
> + status = "disabled";
> + };
> +
> + eth0: ethernet at 80010000 {
> + compatible = "cirrus,ep9301-eth";
> + reg = <0x80010000 0x10000>;
> + interrupt-parent = <&vic1>;
> + interrupts = <7>;
> + mdio0: mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
Your SoC comes with mdio? If so, why is this empty?
> + };
> + };
> +
> + rtc0: rtc at 80920000 {
> + compatible = "cirrus,ep9301-rtc";
> + reg = <0x80920000 0x100>;
> + };
> +
> + spi0: spi at 808a0000 {
> + compatible = "cirrus,ep9301-spi";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x808a0000 0x18>;
> + interrupt-parent = <&vic1>;
> + interrupts = <21>;
> + clocks = <&eclk EP93XX_CLK_SPI>;
> + cs-gpios = <&gpio5 2 0>;
defines... but why is it here in the first place? Rarely CS gpios are
part of the SoC. I have several of such questions further as well, so
this looks like you are mixing SoC and boards in one file.
> + cirrus,ep9301-use-dma;
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi_default_pins>;
> + status = "disabled";
> + };
> +
> + adc: adc at 80900000 {
> + compatible = "cirrus,ep9301-adc";
> + reg = <0x80900000 0x28>;
> + clocks = <&eclk EP93XX_CLK_ADC>;
> + interrupt-parent = <&vic0>;
> + interrupts = <30>;
> + status = "disabled";
> + };
> +
> + watchdog0: watchdog at 80940000 {
> + compatible = "cirrus,ep9301-wdt";
> + reg = <0x80940000 0x08>;
> + };
> +
> + pwm0: pwm at 80910000 {
> + compatible = "cirrus,ep9301-pwm";
> + reg = <0x80910000 0x10>;
> + clocks = <&eclk EP93XX_CLK_PWM>;
> + status = "disabled";
> + };
> +
> + pwm1: pwm at 80910020 {
> + compatible = "cirrus,ep9301-pwm";
> + reg = <0x80910020 0x10>;
> + clocks = <&eclk EP93XX_CLK_PWM>;
> + status = "disabled";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwm1_default_pins>;
> + };
> +
> + keypad: keypad at 800f0000 {
> + compatible = "cirrus,ep9307-keypad";
> + reg = <0x800f0000 0x0c>;
> + interrupt-parent = <&vic0>;
> + interrupts = <29>;
> + clocks = <&eclk EP93XX_CLK_KEYPAD>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&keypad_default_pins>;
> + linux,keymap =
> + <KEY_UP>,
> + <KEY_DOWN>,
> + <KEY_VOLUMEDOWN>,
> + <KEY_HOME>,
> + <KEY_RIGHT>,
> + <KEY_LEFT>,
> + <KEY_ENTER>,
> + <KEY_VOLUMEUP>,
> + <KEY_F6>,
> + <KEY_F8>,
> + <KEY_F9>,
> + <KEY_F10>,
> + <KEY_F1>,
> + <KEY_F2>,
> + <KEY_F3>,
> + <KEY_POWER>;
> + };
> + };
> +
> + xtali: oscillator {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <14745600>;
> + clock-output-names = "xtali";
> + };
> +
> + i2c0: i2c0 {
i2c or i2c-0
> + compatible = "i2c-gpio";
> + sda-gpios = <&gpio6 1 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
> + scl-gpios = <&gpio6 0 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
Wait, what? Why this is disabled? If this is part of the SoC, although
hardly looks like, then it should be complete. What is missing? How one
could design SoC with incomplete GPIO I2C controller?
> + };
> +
> + leds {
> + compatible = "gpio-leds";
I really doubt this is property of the SoC. Please double check as it
really looks wrong.
> + led0 {
led-0
> + label = "grled";
> + gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + function = LED_FUNCTION_HEARTBEAT;
> + };
> +
> + led1 {
led-1
> + label = "rdled";
> + gpios = <&gpio4 1 GPIO_ACTIVE_HIGH>;
> + function = LED_FUNCTION_FAULT;
> + };
> + };
> +};
Best regards,
Krzysztof
More information about the linux-arm-kernel
mailing list