[PATCH v2 4/4] arm64: dts: freescale: Add DEBIX SOM A and SOM A I/O Board support

[Marco Felsch]

Hi Shawn,

On 23-07-19, Shawn Guo wrote:
> On Mon, Jul 17, 2023 at 06:51:27PM +0200, Marco Felsch wrote:

...

> > +	reg_baseboard_vdd3v3: regulator-baseboard-vdd3v3 {
> > +		compatible = "regulator-fixed";
> > +		regulator-min-microvolt = <3300000>;
> > +		regulator-max-microvolt = <3300000>;
> > +		regulator-name = "BB_VDD3V3";
> > +		gpio = <&expander0 10 GPIO_ACTIVE_HIGH>;
> > +		/* Required timings for ethernet phy's */
> > +		startup-delay-us = <50000>;
> > +		off-on-delay-us = <110000>;
> > +		enable-active-high;
> 
> Can we place this right after the line below?
> 
>   gpio = <&expander0 10 GPIO_ACTIVE_HIGH>;

Sure.

> > +		regulator-always-on;
> > +	};

...

> > +&i2c4 {
> > +	expander0: gpio at 20 {
> > +		compatible = "nxp,pca9535";
> > +		reg = <0x20>;
> > +		gpio-controller;
> > +		#gpio-cells = <0x02>;
> > +	};
> > +
> > +	expander1: gpio at 23 {
> > +		compatible = "nxp,pca9535";
> > +		reg = <0x23>;
> > +		gpio-controller;
> > +		#gpio-cells = <0x02>;
> > +
> > +		/*
> > +		 * Since USB1 is bound to peripheral mode we need to ensure
> > +		 * that VBUS is turned off.
> > +		 */
> > +		usb30-otg-hog {
> > +			gpio-hog;
> > +			gpios = <13 GPIO_ACTIVE_HIGH>;
> > +			output-low;
> > +			line-name = "USB30_OTG_EN";
> > +		};
> > +	};
> > +
> > +	eeprom at 52 {
> > +		compatible = "atmel,24c02";
> > +		reg = <0x52>;
> > +		pagesize = <16>;
> > +	};
> > +
> > +	rtc at 51 {
> 
> Sort them in order of unit-address.

Of course, thanks.

> > +		compatible = "haoyu,hym8563";
> > +		reg = <0x51>;
> > +		pinctrl-names = "default";
> > +		pinctrl-0 = <&pinctrl_rtc>;
> > +		interrupt-parent = <&gpio4>;
> > +		interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
> > +		#clock-cells = <0>;
> > +	};
> > +};

> > +&i2c4 {
> > +	clock-frequency = <400000>;
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&pinctrl_i2c4>;
> > +	status = "okay";
> > +
> > +	adc at 48 {
> > +		 compatible = "ti,ads1115";
> > +		 reg = <0x48>;
> > +
> 
> Unnecessary newline.

Dropped it, thanks.

> > +		 #address-cells = <1>;
> > +		 #size-cells = <0>;
> > +
> > +		 channel at 4 {
> > +			 reg = <4>;
> > +			 ti,gain = <1>;
> > +			 ti,datarate = <7>;
> > +		 };
> 
> Have a newline between nodes.

Sure.

Regards,
  Marco