[PATCH v3 8/8] ARM: dts: stm32: Add Octavo OSD32MP1-RED board

[Krzysztof Kozlowski]

On 12/07/2023 08:29, Sean Nyekjaer wrote:
> Add support for the Octavo OSD32MP1-RED development board.
> 
> General features:
>  - STM32MP157C
>  - 512MB DDR3
>  - CAN-FD
>  - HDMI
>  - USB-C OTG
>  - UART
> 

...

> +
> +&i2c1 {
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&i2c1_pins_a>;
> +	pinctrl-1 = <&i2c1_sleep_pins_a>;
> +	status = "okay";
> +	i2c-scl-rising-time-ns = <100>;
> +	i2c-scl-falling-time-ns = <7>;
> +	/delete-property/dmas;
> +	/delete-property/dma-names;

You should explain it with comment, unless it is quite common for all
STM32 boards to disable DMA for I2C...

> +
> +	hdmi-transmitter at 39 {
> +		compatible = "sil,sii9022";
> +		reg = <0x39>;
> +		reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>;
> +		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
> +		interrupt-parent = <&gpiog>;
> +		pinctrl-names = "default", "sleep";
> +		pinctrl-0 = <&ltdc_pins_e>;
> +		pinctrl-1 = <&ltdc_sleep_pins_e>;
> +		status = "okay";

Did anything disable this node?

> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port at 0 {
> +				reg = <0>;
> +				sii9022_in: endpoint {
> +					remote-endpoint = <&ltdc_ep0_out>;
> +				};
> +			};
> +
> +			port at 1 {
> +				reg = <1>;
> +				sii9022_tx_endpoint: endpoint {
> +					remote-endpoint = <&i2s2_endpoint>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&i2s2 {
> +	clocks = <&rcc SPI2>, <&rcc SPI2_K>, <&rcc CK_PER>, <&rcc PLL3_R>;
> +	clock-names = "pclk", "i2sclk", "x8k", "x11k";
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&i2s2_pins_b>;
> +	pinctrl-1 = <&i2s2_sleep_pins_b>;
> +	status = "okay";
> +
> +	i2s2_port: port {
> +		i2s2_endpoint: endpoint {
> +			remote-endpoint = <&sii9022_tx_endpoint>;
> +			format = "i2s";
> +			mclk-fs = <256>;
> +		};
> +	};
> +};
> +
> +&ltdc {
> +	status = "okay";
> +
> +	port {
> +		ltdc_ep0_out: endpoint at 0 {
> +			reg = <0>;
> +			remote-endpoint = <&sii9022_in>;
> +		};
> +	};
> +};
> +
> +&m_can1 {
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&m_can1_pins_d>;
> +	pinctrl-1 = <&m_can1_sleep_pins_d>;
> +	status = "okay";
> +};
> +
> +&pwr_regulators {
> +	vdd-supply = <&vdd>;
> +	vdd_3v3_usbfs-supply = <&vdd_usb>;
> +};
> +
> +&rtc {
> +	status = "okay";
> +};
> +
> +&sdmmc1 {
> +	pinctrl-names = "default", "opendrain", "sleep";
> +	pinctrl-0 = <&sdmmc1_b4_pins_a>;
> +	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
> +	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
> +	cd-gpios = <&gpioe 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> +	disable-wp;
> +	st,neg-edge;
> +	bus-width = <4>;
> +	vmmc-supply = <&v3v3>;
> +	status = "okay";
> +};
> +
> +&sdmmc2 {
> +	pinctrl-names = "default", "opendrain", "sleep";
> +	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_d>;
> +	pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
> +	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_d>;
> +	non-removable;
> +	no-sd;
> +	no-sdio;
> +	st,neg-edge;
> +	bus-width = <8>;
> +	vmmc-supply = <&v3v3>;
> +	vqmmc-supply = <&vdd>;
> +	mmc-ddr-3_3v;
> +	status = "okay";
> +};
> +
> +&uart4 {
> +	pinctrl-names = "default", "sleep", "idle";
> +	pinctrl-0 = <&uart4_pins_a>;
> +	pinctrl-1 = <&uart4_sleep_pins_a>;
> +	pinctrl-2 = <&uart4_idle_pins_a>;
> +	/delete-property/dmas;
> +	/delete-property/dma-names;

Same concerns.

Best regards,
Krzysztof