[PATCH V2 8/9] arm64: dts: qcom: add IPQ5332 SoC and MI01.2 board support

[Konrad Dybcio]

On 30.01.2023 12:47, Kathiravan Thirumoorthy wrote:
> From: Kathiravan T <quic_kathirav at quicinc.com>
> 
> Add initial device tree support for the Qualcomm IPQ5332 SoC and
> MI01.2 board.
> 
> Signed-off-by: Kathiravan T <quic_kathirav at quicinc.com>
> ---
[...]

> +
> +	reserved-memory {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		tz_mem: tz at 4a600000 {
> +			no-map;
> +			reg = <0x0 0x4a600000 0x0 0x200000>;
reg should come before no-map


> +		};
> +	};
> +
> +	soc at 0 {
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges = <0 0 0 0xffffffff>;
> +
> +		tlmm: pinctrl at 1000000 {
> +			compatible = "qcom,ipq5332-tlmm";
> +			reg = <0x01000000 0x300000>;
> +			interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>;
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +			gpio-ranges = <&tlmm 0 0 53>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +
> +			serial_0_pins: serial0-state {
> +				pins = "gpio18", "gpio19";
> +				function = "blsp0_uart0";
> +				drive-strength = <8>;
> +				bias-pull-up;
> +			};
> +		};
> +
> +		gcc: clock-controller at 1800000 {
> +			compatible = "qcom,ipq5332-gcc";
> +			reg = <0x01800000 0x80000>;
> +			#clock-cells = <1>;
> +			#reset-cells = <1>;
> +			#power-domain-cells = <1>;
> +			clock-names = "xo",
> +				      "sleep_clk",
> +				      "pcie_2lane_phy_pipe_clk",
> +				      "pcie_2lane_phy_pipe_clk_x1",
> +				      "usb_pcie_wrapper_pipe_clk";
> +			clocks = <&xo_board>,
> +				 <&sleep_clk>,
> +				 <0>,
> +				 <0>,
> +				 <0>;
> +		};
> +
> +		sdhc: mmc at 7804000 {
> +			compatible = "qcom,ipq5332-sdhci", "qcom,sdhci-msm-v5";
> +			reg = <0x07804000 0x1000>, <0x07805000 0x1000>;
> +
> +			interrupts = <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "hc_irq", "pwr_irq";
> +
> +			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
> +				 <&gcc GCC_SDCC1_APPS_CLK>,
> +				 <&xo_board>;
> +			clock-names = "iface", "core", "xo";
> +			mmc-ddr-1_8v;
> +			mmc-hs200-1_8v;
> +			max-frequency = <192000000>;
> +			bus-width = <4>;
> +			status = "disabled";
> +		};
> +
> +		blsp1_uart0: serial at 78af000 {
> +			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
> +			reg = <0x078af000 0x200>;
> +			interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
> +				 <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			status = "disabled";
> +		};
> +
> +		intc: interrupt-controller at b000000 {
> +			compatible = "qcom,msm-qgic2";
> +			reg = <0x0b000000 0x1000>,	/* GICD */
> +			      <0x0b002000 0x1000>,	/* GICC */
> +			      <0x0b001000 0x1000>,	/* GICH */
> +			      <0x0b004000 0x1000>;	/* GICV */
> +			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0 0x0b00c000 0x3000>;
> +
> +			v2m0: v2m at 0 {
> +				compatible = "arm,gic-v2m-frame";
> +				reg = <0x00000000 0xffd>;
> +				msi-controller;
> +			};
> +
> +			v2m1: v2m at 1 {
> +				compatible = "arm,gic-v2m-frame";
> +				reg = <0x00001000 0xffd>;
The unit address does not match the address part of the reg
property, dtbs_check will not succeed..

The rest lgtm

Konrad
> +				msi-controller;
> +			};
> +
> +			v2m2: v2m at 2 {
> +				compatible = "arm,gic-v2m-frame";
> +				reg = <0x00002000 0xffd>;
> +				msi-controller;
> +			};
> +		};
> +
> +		timer at b120000 {
> +			compatible = "arm,armv7-timer-mem";
> +			reg = <0x0b120000 0x1000>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +
> +			frame at b120000 {
> +				reg = <0x0b121000 0x1000>,
> +				      <0x0b122000 0x1000>;
> +				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> +				frame-number = <0>;
> +			};
> +
> +			frame at b123000 {
> +				reg = <0x0b123000 0x1000>;
> +				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
> +				frame-number = <1>;
> +				status = "disabled";
> +			};
> +
> +			frame at b124000 {
> +				reg = <0x0b124000 0x1000>;
> +				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
> +				frame-number = <2>;
> +				status = "disabled";
> +			};
> +
> +			frame at b125000 {
> +				reg = <0x0b125000 0x1000>;
> +				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> +				frame-number = <3>;
> +				status = "disabled";
> +			};
> +
> +			frame at b126000 {
> +				reg = <0x0b126000 0x1000>;
> +				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> +				frame-number = <4>;
> +				status = "disabled";
> +			};
> +
> +			frame at b127000 {
> +				reg = <0x0b127000 0x1000>;
> +				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> +				frame-number = <5>;
> +				status = "disabled";
> +			};
> +
> +			frame at b128000 {
> +				reg = <0x0b128000 0x1000>;
> +				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> +				frame-number = <6>;
> +				status = "disabled";
> +			};
> +		};
> +	};
> +
> +	timer {
> +		compatible = "arm,armv8-timer";
> +		interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> +	};
> +};