[PATCH v3 4/4] KVM: arm64: Allow no running vcpu on saving vgic3 pending table

[Gavin Shan]

Hi Zenghui,

On 1/28/23 2:57 AM, Zenghui Yu wrote:
> On 2023/1/27 07:54, Gavin Shan wrote:
>> We don't have a running VCPU context to save vgic3 pending table due
>> to KVM_DEV_ARM_VGIC_{GRP_CTRL, SAVE_PENDING_TABLES} command on KVM
>> device "kvm-arm-vgic-v3". The unknown case is caught by kvm-unit-tests.
>>
>>    # ./kvm-unit-tests/tests/its-pending-migration
>>    WARNING: CPU: 120 PID: 7973 at arch/arm64/kvm/../../../virt/kvm/kvm_main.c:3325 \
>>    mark_page_dirty_in_slot+0x60/0xe0
>>     :
>>    mark_page_dirty_in_slot+0x60/0xe0
>>    __kvm_write_guest_page+0xcc/0x100
>>    kvm_write_guest+0x7c/0xb0
>>    vgic_v3_save_pending_tables+0x148/0x2a0
>>    vgic_set_common_attr+0x158/0x240
>>    vgic_v3_set_attr+0x4c/0x5c
>>    kvm_device_ioctl+0x100/0x160
>>    __arm64_sys_ioctl+0xa8/0xf0
>>    invoke_syscall.constprop.0+0x7c/0xd0
>>    el0_svc_common.constprop.0+0x144/0x160
>>    do_el0_svc+0x34/0x60
>>    el0_svc+0x3c/0x1a0
>>    el0t_64_sync_handler+0xb4/0x130
>>    el0t_64_sync+0x178/0x17c
>>
>> Use vgic_write_guest_lock() to save vgic3 pending table.
>>
>> Reported-by: Zenghui Yu <yuzenghui at huawei.com>
>> Signed-off-by: Gavin Shan <gshan at redhat.com>
>> Reviewed-by: Oliver Upton <oliver.upton at linux.dev>
>> ---
>>  Documentation/virt/kvm/api.rst | 4 +++-
>>  arch/arm64/kvm/vgic/vgic-v3.c  | 2 +-
>>  2 files changed, 4 insertions(+), 2 deletions(-)
>>
>> diff --git a/Documentation/virt/kvm/api.rst b/Documentation/virt/kvm/api.rst
>> index 40ada313faa3..07f07668995e 100644
>> --- a/Documentation/virt/kvm/api.rst
>> +++ b/Documentation/virt/kvm/api.rst
>> @@ -8074,7 +8074,9 @@ NOTE: Multiple examples of using the backup bitmap: (1) save vgic/its
>>  tables through command KVM_DEV_ARM_{VGIC_GRP_CTRL, ITS_SAVE_TABLES} on
>>  KVM device "kvm-arm-vgic-its". (2) restore vgic/its tables through
>>  command KVM_DEV_ARM_{VGIC_GRP_CTRL, ITS_RESTORE_TABLES} on KVM device
>> -"kvm-arm-vgic-its". vgic3 LPI pending status is restored.
>> +"kvm-arm-vgic-its". vgic3 LPI pending status is restored. (3) save
>> +vgic3 pending table through KVM_DEV_ARM_VGIC_{GRP_CTRL, SAVE_PENDING_TABLES}
>> +command on KVM device "kvm-arm-vgic-v3".
> 
> Can we summarize these 3 examples with something like: "when the guest
> memory (pending tables, ITS tables, etc) is dirtied by the virtual GIC
> or ITS, which is typically triggered by a userspace request (e.g.,
> KVM_DEV_ARM_ITS_SAVE_TABLES) and doesn't require a running VCPU
> context"? In case there will be more no-running-vcpu
> kvm_write_guest_lock() cases in the VGIC emulation code in future and we
> have to extend the documentation..
> 
> But I don't have objection to your writing and the whole series looks
> good.
> 

There are discussions about the documentation when dirty ring is enabled
on ARM64. We prefer to keep the layout where the KVM devices and commands
are explicitly documented. The application developer can identify them
easily and to enable the backup bitmap when those KVM devices have been
used.

By the way, 'vgic3' will be replaced with 'VGICv3' as you suggested in
another reply.

Thanks,
Gavin