[PATCH 2/2] arm64: dts: meson: add support for Radxa Zero2
Krzysztof Kozlowski
krzysztof.kozlowski at linaro.org
Fri Jan 27 04:34:05 PST 2023
On 27/01/2023 12:09, Christian Hewitt wrote:
> From: Yuntian Zhang <yt at radxa.com>
>
> Radxa Zero2 is a small form factor SBC based on the Amlogic A311D
> chipset that ships in a number of eMMC configurations:
>
Thank you for your patch. There is something to discuss/improve.
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
> + clocks = <&wifi32k>;
> + clock-names = "ext_clock";
> + };
> +
> + ao_5v: regulator-ao_5v {
No underscores in node names.
> + compatible = "regulator-fixed";
> + regulator-name = "AO_5V";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +
> + vcc_1v8: regulator-vcc_1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc_3v3>;
> + regulator-always-on;
> + };
> +
> + vcc_3v3: regulator-vcc_3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vddao_3v3>;
> + regulator-always-on;
> + /* FIXME: actually controlled by VDDCPU_B_EN */
> + };
> +
> + vddao_1v8: regulator-vddao_1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDIO_AO1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vddao_3v3>;
> + regulator-always-on;
> + };
> +
> + vddao_3v3: regulator-vddao_3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDAO_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&ao_5v>;
> + regulator-always-on;
> + };
> +
> + vddcpu_a: regulator-vddcpu-a {
> + /*
> + * MP8756GD Regulator.
> + */
> + compatible = "pwm-regulator";
> +
> + regulator-name = "VDDCPU_A";
> + regulator-min-microvolt = <730000>;
> + regulator-max-microvolt = <1022000>;
> +
> + pwm-supply = <&ao_5v>;
> +
> + pwms = <&pwm_ab 0 1250 0>;
> + pwm-dutycycle-range = <100 0>;
> +
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vddcpu_b: regulator-vddcpu-b {
> + /*
> + * Silergy SY8120B1ABC Regulator.
> + */
> + compatible = "pwm-regulator";
> +
> + regulator-name = "VDDCPU_B";
> + regulator-min-microvolt = <730000>;
> + regulator-max-microvolt = <1022000>;
> +
> + pwm-supply = <&ao_5v>;
> +
> + pwms = <&pwm_AO_cd 1 1250 0>;
> + pwm-dutycycle-range = <100 0>;
> +
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sound {
> + compatible = "amlogic,axg-sound-card";
> + model = "RADXA-ZERO2";
> + audio-aux-devs = <&tdmout_b>;
> + audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
> + "TDMOUT_B IN 1", "FRDDR_B OUT 1",
> + "TDMOUT_B IN 2", "FRDDR_C OUT 1",
> + "TDM_B Playback", "TDMOUT_B OUT";
> +
> + assigned-clocks = <&clkc CLKID_MPLL2>,
> + <&clkc CLKID_MPLL0>,
> + <&clkc CLKID_MPLL1>;
> + assigned-clock-parents = <0>, <0>, <0>;
> + assigned-clock-rates = <294912000>,
> + <270950400>,
> + <393216000>;
> +
> + dai-link-0 {
> + sound-dai = <&frddr_a>;
> + };
> +
> + dai-link-1 {
> + sound-dai = <&frddr_b>;
> + };
> +
> + dai-link-2 {
> + sound-dai = <&frddr_c>;
> + };
> +
> + /* 8ch hdmi interface */
> + dai-link-3 {
> + sound-dai = <&tdmif_b>;
> + dai-format = "i2s";
> + dai-tdm-slot-tx-mask-0 = <1 1>;
> + dai-tdm-slot-tx-mask-1 = <1 1>;
> + dai-tdm-slot-tx-mask-2 = <1 1>;
> + dai-tdm-slot-tx-mask-3 = <1 1>;
> + mclk-fs = <256>;
> +
> + codec {
> + sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
> + };
> + };
> +
> + /* hdmi glue */
> + dai-link-4 {
> + sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
> +
> + codec {
> + sound-dai = <&hdmi_tx>;
> + };
> + };
> + };
> +
> + wifi32k: wifi32k {
Generic node names, so clock-0 or clock-xyz
Best regards,
Krzysztof
More information about the linux-arm-kernel
mailing list