[PATCH 1/2] dt-bindings: pinctrl: add bindings for MT7981 SoC
Rob Herring
robh at kernel.org
Mon Jan 23 14:59:43 PST 2023
On Sun, Jan 22, 2023 at 06:23:55PM +0000, Daniel Golle wrote:
> Add bindings for the MT7981 pinctrl driver, based on existing MT7986
> pinctrl bindings.
What existing bindings? A .txt file you need to remove, or undocumented,
but in use somewhere (where?)?
> Signed-off-by: Daniel Golle <daniel at makrotopia.org>
> ---
> .../pinctrl/mediatek,mt7981-pinctrl.yaml | 475 ++++++++++++++++++
> 1 file changed, 475 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt7981-pinctrl.yaml
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt7981-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7981-pinctrl.yaml
> new file mode 100644
> index 0000000000000..e76fe0d5083a3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7981-pinctrl.yaml
> @@ -0,0 +1,475 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/mediatek,mt7981-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Mediatek MT7981 Pin Controller
> +
> +maintainers:
> + - Daniel Golle <daniel at makrotopia.org>
> +
> +description: |+
Don't need '|+' unless there are line endings to preserve.
> + The MediaTek's MT7981 Pin controller is used to control SoC pins.
> +
> +properties:
> + compatible:
> + enum:
> + - mediatek,mt7981-pinctrl
> +
> + reg:
> + minItems: 9
> + maxItems: 9
> +
> + reg-names:
> + items:
> + - const: gpio
> + - const: iocfg_rt
> + - const: iocfg_rm
> + - const: iocfg_rb
> + - const: iocfg_lb
> + - const: iocfg_bl
> + - const: iocfg_tm
> + - const: iocfg_tl
> + - const: eint
> +
> + gpio-controller: true
> +
> + "#gpio-cells":
> + const: 2
> + description: |
> + Number of cells in GPIO specifier. Since the generic GPIO
> + binding is used, the amount of cells must be specified as 2. See the below
> + mentioned gpio binding representation for description of particular cells.
> +
> + gpio-ranges:
> + minItems: 1
> + maxItems: 5
> + description: |
> + GPIO valid number range.
> +
> + interrupt-controller: true
> +
> + interrupts:
> + maxItems: 1
> +
> + "#interrupt-cells":
> + const: 2
> +
> +allOf:
> + - $ref: "pinctrl.yaml#"
Drop quotes
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - gpio-controller
> + - "#gpio-cells"
> +
> +patternProperties:
> + '-pins$':
> + type: object
> + additionalProperties: false
> +
> + patternProperties:
> + '.*mux.*':
Just to be really clear: '^.*mux.*$'
Really, if not already in use, it would be preferred if this was either
a prefix or a suffix.
> + type: object
> + additionalProperties: false
> + description: |
> + pinmux configuration nodes.
> +
> + The following table shows the effective values of "group", "function"
> + properties and chip pinout pins
> +
> + groups function pins (in pin#)
> + ---------------------------------------------------------------------
> + "wa_aice1" "wa_aice" 0, 1
> + "wa_aice2" "wa_aice" 0, 1
> + "wm_uart_0" "uart" 0, 1
> + "dfd" "dfd" 0, 1, 4, 5
> + "watchdog" "watchdog" 2
> + "pcie_pereset" "pcie" 3
> + "jtag" "jtag" 4, 5, 6, 7, 8
> + "wm_jtag_0" "jtag" 4, 5, 6, 7, 8
> + "wo0_jtag_0" "jtag" 9, 10, 11, 12, 13
> + "uart2_0" "uart" 4, 5, 6, 7
> + "gbe_led0" "led" 8
> + "pta_ext_0" "pta" 4, 5, 6
> + "pwm2" "pwm" 7
> + "net_wo0_uart_txd_0" "uart" 8
> + "spi1_0" "spi" 4, 5, 6, 7
> + "i2c0_0" "i2c" 6, 7
> + "dfd_ntrst" "dfd" 8
> + "wm_aice1" "wa_aice" 9, 10
> + "pwm0_0" "pwm" 13
> + "pwm0_1" "pwm" 15
> + "pwm1_0" "pwm" 14
> + "pwm1_1" "pwm" 15
> + "net_wo0_uart_txd_1" "uart" 14
> + "net_wo0_uart_txd_2" "uart" 15
> + "gbe_led1" "led" 13
> + "pcm" "pcm" 9, 10, 11, 12, 13, 25
> + "watchdog1" "watchdog" 13
> + "udi" "udi" 9, 10, 11, 12, 13
> + "drv_vbus" "usb" 14
> + "emmc_45" "flash" 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25
> + "snfi" "flash" 16, 17, 18, 19, 20, 21
> + "spi0" "spi" 16, 17, 18, 19
> + "spi0_wp_hold" "spi" 20, 21
> + "spi1_1" "spi" 22, 23, 24, 25
> + "spi2" "spi" 26, 27, 28, 29
> + "spi2_wp_hold" "spi" 30, 31
> + "uart1_0" "uart" 16, 17, 18, 19
> + "uart1_1" "uart" 26, 27, 28, 29
> + "uart2_1" "uart" 22, 23, 24, 25
> + "pta_ext_1" "pta" 22, 23, 24
> + "wm_aurt_1" "uart" 20, 21
> + "wm_aurt_2" "uart" 30, 31
> + "wm_jtag_1" "jtag" 20, 21, 22, 23, 24
> + "wo0_jtag_1" "jtag" 25, 26, 27, 28, 29
> + "wa_aice3" "wa_aice" 28, 20
> + "wm_aice2" "wa_aice" 30, 31
> + "i2c0_1" "i2c" 30, 31
> + "u2_phy_i2c" "i2c" 30, 31
> + "uart0" "uart" 32, 33
> + "sgmii1_phy_i2c" "i2c" 32, 33
> + "u3_phy_i2c" "i2c" 32, 33
> + "sgmii0_phy_i2c" "i2c" 32, 33
> + "pcie_clk" "pcie" 34
> + "pcie_wake" "pcie" 35
> + "i2c0_2" "i2c" 36, 37
> + "smi_mdc_mdio" "eth" 36, 37
> + "gbe_ext_mdc_mdio" "eth" 36, 37
> + "wf0_mode1" "eth" 40, 41, 42, 43, 44, 45, 46, 47, 48,
> + 49, 50, 51, 52, 53, 54, 55, 56
> +
> + "wf0_mode3" "eth" 45, 46, 47, 48, 49, 51
> + "wf2g_led0" "led" 30
> + "wf2g_led1" "led" 34
> + "wf5g_led0" "led" 31
> + "wf5g_led1" "led" 35
> + "mt7531_int" "eth" 38
> + "ant_sel" "ant" 14, 15, 16, 17, 18, 19, 20, 21, 22
> + 23, 24, 25, 34, 35
> +
> + $ref: "/schemas/pinctrl/pinmux-node.yaml"
Drop quotes.
> + properties:
> + function:
> + description: |
Don't need '|'.
> + A string containing the name of the function to mux to the group.
> + enum: [wa_aice, dfd, jtag, pta, pcm, udi, usb, ant, eth, i2c, led,
> + pwm, spi, uart, watchdog, flash, pcie]
> + groups:
> + description: |
> + An array of strings. Each string contains the name of a group.
Blank line.
> + required:
> + - function
> + - groups
> +
> + allOf:
> + - if:
> + properties:
> + function:
> + const: wa_aice
> + then:
> + properties:
> + groups:
> + enum: [wa_aice1, wa_aice2, wm_aice1_1, wa_aice3, wm_aice1_2]
> + - if:
> + properties:
> + function:
> + const: dfd
> + then:
> + properties:
> + groups:
> + enum: [dfd, dfd_ntrst]
> + - if:
> + properties:
> + function:
> + const: jtag
> + then:
> + properties:
> + groups:
> + enum: [jtag, wm_jtag_0, wo0_jtag_0, wo0_jtag_1, wm_jtag_1]
> + - if:
> + properties:
> + function:
> + const: pta
> + then:
> + properties:
> + groups:
> + enum: [pta_ext_0, pta_ext_1]
> + - if:
> + properties:
> + function:
> + const: pcm
> + then:
> + properties:
> + groups:
> + enum: [pcm]
> + - if:
> + properties:
> + function:
> + const: udi
> + then:
> + properties:
> + groups:
> + enum: [udi]
> + - if:
> + properties:
> + function:
> + const: usb
> + then:
> + properties:
> + groups:
> + enum: [drv_vbus]
> + - if:
> + properties:
> + function:
> + const: ant
> + then:
> + properties:
> + groups:
> + enum: [ant_sel]
> + - if:
> + properties:
> + function:
> + const: eth
> + then:
> + properties:
> + groups:
> + enum: [smi_mdc_mdio, gbe_ext_mdc_mdio, wf0_mode1, wf0_mode3,
> + mt7531_int]
> + - if:
> + properties:
> + function:
> + const: i2c
> + then:
> + properties:
> + groups:
> + enum: [i2c0_0, i2c0_1, u2_phy_i2c, sgmii1_phy_i2c, u3_phy_i2c,
> + sgmii0_phy_i2c, i2c0_2]
> + - if:
> + properties:
> + function:
> + const: led
> + then:
> + properties:
> + groups:
> + enum: [gbe_led0, gbe_led1, wf2g_led0, wf2g_led1, wf5g_led0, wf5g_led1]
> + - if:
> + properties:
> + function:
> + const: pwm
> + then:
> + properties:
> + groups:
> + items:
> + enum: [pwm2, pwm0_0, pwm0_1, pwm1_0, pwm1_1]
> + maxItems: 3
> + - if:
> + properties:
> + function:
> + const: spi
> + then:
> + properties:
> + groups:
> + items:
> + enum: [spi1_0, spi0, spi0_wp_hold, spi1_1, spi2, spi2_wp_hold]
> + maxItems: 4
> + - if:
> + properties:
> + function:
> + const: uart
> + then:
> + properties:
> + groups:
> + items:
> + enum: [wm_uart_0, uart2_0, net_wo0_uart_txd_0,
> + net_wo0_uart_txd_1, net_wo0_uart_txd_2, uart1_0,
> + uart1_1, uart2_1, wm_aurt_1, wm_aurt_2, uart0]
> + - if:
> + properties:
> + function:
> + const: watchdog
> + then:
> + properties:
> + groups:
> + enum: [watchdog]
> + - if:
> + properties:
> + function:
> + const: flash
> + then:
> + properties:
> + groups:
> + items:
> + enum: [emmc_45, snfi]
> + maxItems: 1
> + - if:
> + properties:
> + function:
> + const: pcie
> + then:
> + properties:
> + groups:
> + items:
> + enum: [pcie_clk, pcie_wake, pcie_pereset]
> + maxItems: 3
> + '.*conf.*':
Same comments as 'mux'.
> + type: object
> + additionalProperties: false
> + description: |
> + pinconf configuration nodes.
> + $ref: "/schemas/pinctrl/pincfg-node.yaml"
Drop quotes.
> +
> + properties:
> + pins:
> + description: |
> + An array of strings. Each string contains the name of a pin.
> + items:
> + enum: [GPIO_WPS, GPIO_RESET, SYS_WATCHDOG, PCIE_PERESET_N,
> + JTAG_JTDO, JTAG_JTDI, JTAG_JTMS, JTAG_JTCLK, JTAG_JTRST_N,
> + WO_JTAG_JTDO, WO_JTAG_JTDI, WO_JTAG_JTMS, WO_JTAG_JTCLK,
> + WO_JTAG_JTRST_N, USB_VBUS, PWM0, SPI0_CLK, SPI0_MOSI,
> + SPI0_MISO, SPI0_CS, SPI0_HOLD, SPI0_WP, SPI1_CLK, SPI1_MOSI,
> + SPI1_MISO, SPI1_CS, SPI2_CLK, SPI2_MOSI, SPI2_MISO, SPI2_CS,
> + SPI2_HOLD, SPI2_WP, UART0_RXD, UART0_TXD, PCIE_CLK_REQ,
> + PCIE_WAKE_N, SMI_MDC, SMI_MDIO, GBE_INT, GBE_RESET,
> + WF_DIG_RESETB, WF_CBA_RESETB, WF_XO_REQ, WF_TOP_CLK,
> + WF_TOP_DATA, WF_HB1, WF_HB2, WF_HB3, WF_HB4, WF_HB0,
> + WF_HB0_B, WF_HB5, WF_HB6, WF_HB7, WF_HB8, WF_HB9, WF_HB10]
> + maxItems: 57
> +
> + bias-disable: true
> +
> + bias-pull-up:
> + oneOf:
> + - type: boolean
> + description: normal pull up.
> + - enum: [100, 101, 102, 103]
> + description: |
> + PUPD/R1/R0 pull down type. See MTK_PUPD_SET_R1R0 defines in
> + dt-bindings/pinctrl/mt65xx.h.
> +
> + bias-pull-down:
> + oneOf:
> + - type: boolean
> + description: normal pull down.
> + - enum: [100, 101, 102, 103]
> + description: |
> + PUPD/R1/R0 pull down type. See MTK_PUPD_SET_R1R0 defines in
> + dt-bindings/pinctrl/mt65xx.h.
> +
> + input-enable: true
> +
> + input-disable: true
> +
> + output-enable: true
> +
> + output-low: true
> +
> + output-high: true
> +
> + input-schmitt-enable: true
> +
> + input-schmitt-disable: true
> +
> + drive-strength:
> + enum: [2, 4, 6, 8, 10, 12, 14, 16]
> +
> + mediatek,pull-up-adv:
> + description: |
> + Valid arguments for 'mediatek,pull-up-adv' are '0', '1', '2', '3'
> + Pull up setings for 2 pull resistors, R0 and R1. Valid arguments
> + are described as below:
> + 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
> + 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
> + 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
> + 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [0, 1, 2, 3]
> +
> + mediatek,pull-down-adv:
> + description: |
> + Valid arguments for 'mediatek,pull-up-adv' are '0', '1', '2', '3'
> + Pull down setings for 2 pull resistors, R0 and R1. Valid arguments
> + are described as below:
> + 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
> + 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
> + 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
> + 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [0, 1, 2, 3]
> +
> + required:
> + - pins
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/irq.h>
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/pinctrl/mt65xx.h>
> +
> + soc {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + pio: pinctrl at 11d00000 {
> + compatible = "mediatek,mt7981-pinctrl";
> + reg = <0 0x11d00000 0 0x1000>,
> + <0 0x11c00000 0 0x1000>,
> + <0 0x11c10000 0 0x1000>,
> + <0 0x11d20000 0 0x1000>,
> + <0 0x11e00000 0 0x1000>,
> + <0 0x11e20000 0 0x1000>,
> + <0 0x11f00000 0 0x1000>,
> + <0 0x11f10000 0 0x1000>,
> + <0 0x1000b000 0 0x1000>;
> + reg-names = "gpio", "iocfg_rt", "iocfg_rm",
> + "iocfg_rb", "iocfg_lb", "iocfg_bl",
> + "iocfg_tm", "iocfg_tl", "eint";
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&pio 0 0 56>;
> + interrupt-controller;
> + interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-parent = <&gic>;
> + #interrupt-cells = <2>;
> +
> + mdio_pins: mdio-pins {
> + mux {
> + function = "eth";
> + groups = "smi_mdc_mdio";
> + };
> + };
> +
> + spi0_flash_pins: spi0-pins {
> + mux {
> + function = "spi";
> + groups = "spi0", "spi0_wp_hold";
> + };
> +
> + conf-pu {
> + pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
> + };
> +
> + conf-pd {
> + pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
> + };
> + };
> +
> + pcie_pins: pcie-pins {
> + mux {
> + function = "pcie";
> + groups = "pcie_clk", "pcie_wake", "pcie_pereset";
> + };
> + };
> +
> + };
> + };
> --
> 2.39.1
>
More information about the linux-arm-kernel
mailing list