[PATCH V5 2/4] ARM: dts: imx6ull-dhcom: Add DH electronics DHCOM i.MX6ULL SoM and PDK2 board
Christoph Niedermaier
cniedermaier at dh-electronics.com
Sun Jan 22 08:20:11 PST 2023
Add support for DH electronics DHCOM SoM and PDK2 rev. 400 carrier
board. This is an SoM with i.MX6ULL and an evaluation kit. The
baseboard provides Ethernet, UART, USB, CAN and optional display.
Signed-off-by: Christoph Niedermaier <cniedermaier at dh-electronics.com>
Reviewed-by: Marek Vasut <marex at denx.de>
---
Cc: Rob Herring <robh+dt at kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt at linaro.org>
Cc: Peng Fan <peng.fan at nxp.com>
Cc: Shawn Guo <shawnguo at kernel.org>
Cc: Marek Vasut <marex at denx.de>
Cc: Fabio Estevam <festevam at denx.de>
Cc: NXP Linux Team <linux-imx at nxp.com>
Cc: kernel at dh-electronics.com
To: linux-arm-kernel at lists.infradead.org
---
V2: - Remove unnecessary status properties
- Reorder comments in front of a block
- Reorder compatible and reg to the beginning of a node
V3: - Change audio codec node name
- Add comment to the operating points
V4: - Update year in copyright
- Update WiFi compatible node
V5: - Update compatible node of the touchscreen
- Add Reviewed-by tag
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6ull-dhcom-pdk2.dts | 222 +++++++++++
arch/arm/boot/dts/imx6ull-dhcom-som.dtsi | 633 +++++++++++++++++++++++++++++++
arch/arm/boot/dts/imx6ull-dhcor-som.dtsi | 255 +++++++++++++
4 files changed, 1111 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6ull-dhcom-pdk2.dts
create mode 100644 arch/arm/boot/dts/imx6ull-dhcom-som.dtsi
create mode 100644 arch/arm/boot/dts/imx6ull-dhcor-som.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 8029a2b3d078..6c2f4c72d72f 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -741,6 +741,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ull-colibri-wifi-eval-v3.dtb \
imx6ull-colibri-wifi-iris.dtb \
imx6ull-colibri-wifi-iris-v2.dtb \
+ imx6ull-dhcom-pdk2.dtb \
imx6ull-jozacp.dtb \
imx6ull-kontron-bl.dtb \
imx6ull-myir-mys-6ulx-eval.dtb \
diff --git a/arch/arm/boot/dts/imx6ull-dhcom-pdk2.dts b/arch/arm/boot/dts/imx6ull-dhcom-pdk2.dts
new file mode 100644
index 000000000000..b29713831a74
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-dhcom-pdk2.dts
@@ -0,0 +1,222 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2023 DH electronics GmbH
+ *
+ * DHCOM iMX6ULL variant:
+ * DHCM-iMX6ULL-C080-R051-F0409-SPI-E2-CAN2-RTC-WBT-ADC-I-01D2
+ * DHCOR PCB number: 578-200 or newer
+ * DHCOM PCB number: 579-200 or newer
+ * PDK2 PCB number: 516-400 or newer
+ */
+/dts-v1/;
+
+#include "imx6ull-dhcom-som.dtsi"
+
+/ {
+ model = "DH electronics i.MX6ULL DHCOM on Premium Developer Kit (2)";
+ compatible = "dh,imx6ull-dhcom-pdk2", "dh,imx6ull-dhcom-som",
+ "dh,imx6ull-dhcor-som", "fsl,imx6ull";
+
+ clk_ext_audio_codec: clock-codec {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ };
+
+ display_bl: display-bl {
+ compatible = "pwm-backlight";
+ brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>;
+ default-brightness-level = <8>;
+ enable-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>; /* GPIO G */
+ power-supply = <®_panel_3v3>;
+ pwms = <&pwm1 0 50000 PWM_POLARITY_INVERTED>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ button-0 {
+ gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; /* GPIO A */
+ label = "TA1-GPIO-A";
+ linux,code = <KEY_A>;
+ wakeup-source;
+ };
+
+ button-1 {
+ gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; /* GPIO B */
+ label = "TA2-GPIO-B";
+ linux,code = <KEY_B>;
+ wakeup-source;
+ };
+
+ button-2 {
+ gpios = <&gpio5 2 GPIO_ACTIVE_LOW>; /* GPIO C */
+ label = "TA3-GPIO-C";
+ linux,code = <KEY_C>;
+ wakeup-source;
+ };
+
+ button-3 {
+ gpios = <&gpio5 3 GPIO_ACTIVE_LOW>; /* GPIO D */
+ label = "TA4-GPIO-D";
+ linux,code = <KEY_D>;
+ wakeup-source;
+ };
+ };
+
+ led: led {
+ compatible = "gpio-leds";
+
+ /*
+ * Disable PDK2 LED5, because GPIO E is
+ * already used as touch interrupt.
+ */
+ led-0 {
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "off";
+ function = LED_FUNCTION_INDICATOR;
+ function-enumerator = <5>; /* PDK2 LED5 */
+ gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>; /* GPIO E */
+ status = "disabled";
+ };
+
+ led-1 {
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "off";
+ function = LED_FUNCTION_INDICATOR;
+ function-enumerator = <6>; /* PDK2 LED6 */
+ gpios = <&gpio5 7 GPIO_ACTIVE_HIGH>; /* GPIO F */
+ };
+
+ /*
+ * Disable PDK2 LED7, because GPIO H is
+ * already used for WiFi pin WL_REG_ON.
+ */
+ led-2 {
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "off";
+ function = LED_FUNCTION_INDICATOR;
+ function-enumerator = <7>; /* PDK2 LED7 */
+ gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>; /* GPIO H */
+ status = "disabled";
+ };
+
+ /*
+ * Disable PDK2 LED8, because GPIO I is
+ * already used for BT pin BT_REG_ON.
+ */
+ led-3 {
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "off";
+ function = LED_FUNCTION_INDICATOR;
+ function-enumerator = <8>; /* PDK2 LED8 */
+ gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>; /* GPIO I */
+ status = "disabled";
+ };
+ };
+
+ panel {
+ compatible = "edt,etm0700g0edh6";
+ backlight = <&display_bl>;
+ power-supply = <®_panel_3v3>;
+
+ port {
+ lcd_panel_in: endpoint {
+ remote-endpoint = <&lcd_display_out>;
+ };
+ };
+ };
+
+ /* Filtered supply voltage */
+ reg_pdk2_24v: regulator-pdk2-24v {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-max-microvolt = <24000000>;
+ regulator-min-microvolt = <24000000>;
+ regulator-name = "24V_PDK2";
+ };
+
+ /* PDK2 U35 */
+ reg_pdk2_3v3: regulator-pdk2-3v3 {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "3V3_PDK2";
+ vin-supply = <®_pdk2_24v>;
+ };
+
+ /* 560-200 U1 */
+ reg_panel_3v3: regulator-panel-3v3 {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "3V3_PANEL";
+ vin-supply = <®_pdk2_24v>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,bitclock-master = <&dailink_master>;
+ simple-audio-card,format = "i2s";
+ simple-audio-card,frame-master = <&dailink_master>;
+ simple-audio-card,name = "sgtl5000";
+ simple-audio-card,routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "LINE_IN", "Line In Jack",
+ "Headphone Jack", "HP_OUT";
+ simple-audio-card,widgets =
+ "Microphone", "Mic Jack",
+ "Line", "Line In Jack",
+ "Headphone", "Headphone Jack";
+
+ simple-audio-card,cpu {
+ sound-dai = <&sai2>;
+ };
+
+ dailink_master: simple-audio-card,codec {
+ clocks = <&clk_ext_audio_codec>;
+ sound-dai = <&sgtl5000>;
+ };
+ };
+};
+
+/* DHCOM I2C1 */
+&i2c2 {
+ sgtl5000: audio-codec at a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ #sound-dai-cells = <0>;
+ clocks = <&clk_ext_audio_codec>;
+ VDDA-supply = <®_pdk2_3v3>;
+ VDDIO-supply = <®_pdk2_3v3>;
+ };
+
+ touchscreen at 38 {
+ compatible = "edt,edt-ft5406";
+ reg = <0x38>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <4 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
+ power-supply = <®_panel_3v3>;
+ };
+};
+
+&lcdif {
+ status = "okay";
+
+ port {
+ lcd_display_out: endpoint {
+ remote-endpoint = <&lcd_panel_in>;
+ };
+ };
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&sai2 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-dhcom-som.dtsi b/arch/arm/boot/dts/imx6ull-dhcom-som.dtsi
new file mode 100644
index 000000000000..17837663c0b0
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-dhcom-som.dtsi
@@ -0,0 +1,633 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2023 DH electronics GmbH
+ */
+
+#include "imx6ull-dhcor-som.dtsi"
+
+/ {
+ aliases {
+ /delete-property/ mmc0; /* Avoid double definitions */
+ /delete-property/ mmc1;
+ /delete-property/ spi2;
+ /delete-property/ spi3;
+ i2c0 = &i2c2;
+ i2c1 = &i2c1;
+ mmc2 = &usdhc2;
+ rtc0 = &rtc_i2c;
+ rtc1 = &snvs_rtc;
+ serial0 = &uart1;
+ serial1 = &uart6; /* DHCOM UART2, special hardware required */
+ serial2 = &uart3;
+ serial3 = &uart2; /* Use BT UART always as ttymxc3 */
+ serial4 = &uart4;
+ serial5 = &uart5;
+ spi0 = &ecspi1;
+ spi1 = &ecspi4; /* DHCOM SPI2, special hardware required */
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ reg_ext_3v3_ref: regulator-ext-3v3-ref {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "VCC_3V3_REF";
+ };
+
+ reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+ compatible = "regulator-fixed";
+ regulator-max-microvolt = <5000000>;
+ regulator-min-microvolt = <5000000>;
+ regulator-name = "usb-otg1-vbus";
+ };
+
+ reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
+ compatible = "regulator-fixed";
+ gpio = <&gpio1 5 GPIO_ACTIVE_LOW>;
+ regulator-max-microvolt = <5000000>;
+ regulator-min-microvolt = <5000000>;
+ regulator-name = "usb-otg2-vbus";
+ };
+
+ /* SoM with WiFi/BT: WiFi pin WL_REG_ON is connected to a DHCOM GPIO */
+ /omit-if-no-ref/ usdhc1_pwrseq: usdhc1-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; /* GPIO H */
+ };
+};
+
+/* SoM with WiFi/BT: BT pin BT_REG_ON is connected to a DHCOM GPIO */
+&bluetooth {
+ shutdown-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>; /* GPIO I */
+};
+
+&can1 {
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+/*
+ * The signals for CAN2 TX and RX are routed to the DHCOM UART1 RTS/CTS pins.
+ * Only if this pins are used as CAN interface enable it on board layer.
+ */
+&can2 {
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ pinctrl-names = "default";
+};
+
+/* DHCOM SPI1 */
+&ecspi1 {
+ cs-gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+/*
+ * DHCOM SPI2
+ * Special hardware required that uses the pins of FEC2. Therefore this SPI
+ * interface can only be used if FEC2 is disabled.
+ */
+&ecspi4 {
+ cs-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&pinctrl_ecspi4>;
+ pinctrl-names = "default";
+};
+
+/* DHCOM ETH1 */
+&fec1 {
+ phy-handle = <&mdio2_phy0>;
+ phy-mode = "rmii";
+ pinctrl-0 = <&pinctrl_fec1>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+/* DHCOM ETH2 */
+&fec2 {
+ phy-handle = <&mdio2_phy1>;
+ phy-mode = "rmii";
+ pinctrl-0 = <&pinctrl_fec2>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio2_phy0: ethernet-phy at 0 {
+ compatible = "ethernet-phy-id0007.c0f0", /* SMSC LAN8710Ai */
+ "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ clock-names = "rmii-ref";
+ clocks = <&clks IMX6UL_CLK_ENET_REF>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-0 = <&pinctrl_fec1_phy &pinctrl_snvs_fec1_phy>;
+ pinctrl-names = "default";
+ reset-assert-us = <500>;
+ reset-deassert-us = <500>;
+ reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+ smsc,disable-energy-detect; /* Make plugin detection reliable */
+ };
+
+ mdio2_phy1: ethernet-phy at 1 {
+ compatible = "ethernet-phy-id0007.c0f0", /* SMSC LAN8710Ai */
+ "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ clock-names = "rmii-ref";
+ clocks = <&clks IMX6UL_CLK_ENET2_REF>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-0 = <&pinctrl_fec2_phy &pinctrl_snvs_fec2_phy>;
+ pinctrl-names = "default";
+ reset-assert-us = <500>;
+ reset-deassert-us = <500>;
+ reset-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+ smsc,disable-energy-detect; /* Make plugin detection reliable */
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "DHCOM-INT",
+ "", "", "", "",
+ "", "", "DHCOM-I", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "";
+ pinctrl-0 = <&pinctrl_spi1_switch
+ &pinctrl_dhcom_i &pinctrl_dhcom_int>;
+ pinctrl-names = "default";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "DHCOM-L", "DHCOM-K", "DHCOM-M",
+ "DHCOM-J", "DHCOM-U", "DHCOM-T", "DHCOM-S",
+ "DHCOM-R", "DHCOM-Q", "DHCOM-P", "DHCOM-O",
+ "DHCOM-N", "", "", "";
+ pinctrl-0 = <&pinctrl_dhcom_j &pinctrl_dhcom_k
+ &pinctrl_dhcom_l &pinctrl_dhcom_m
+ &pinctrl_dhcom_n &pinctrl_dhcom_o
+ &pinctrl_dhcom_p &pinctrl_dhcom_q
+ &pinctrl_dhcom_r &pinctrl_dhcom_s
+ &pinctrl_dhcom_t &pinctrl_dhcom_u>;
+ pinctrl-names = "default";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "DHCOM-A", "DHCOM-B", "DHCOM-C", "DHCOM-D",
+ "DHCOM-E", "", "", "DHCOM-F",
+ "DHCOM-G", "DHCOM-H", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "";
+ pinctrl-0 = <&pinctrl_snvs_dhcom_a &pinctrl_snvs_dhcom_b
+ &pinctrl_snvs_dhcom_c &pinctrl_snvs_dhcom_d
+ &pinctrl_snvs_dhcom_e &pinctrl_snvs_dhcom_f
+ &pinctrl_snvs_dhcom_g &pinctrl_snvs_dhcom_h>;
+ pinctrl-names = "default";
+};
+
+/* DHCOM I2C2 */
+&i2c1 {
+ rtc_i2c: rtc at 32 {
+ compatible = "microcrystal,rv8803";
+ reg = <0x32>;
+ };
+
+ /* Microchip 24AA025E48T-I/OT containing MAC for DHCOM ETH1 */
+ eeprom at 50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+
+ /* TI ADC101C027 */
+ adc at 51 {
+ compatible = "ti,adc101c";
+ reg = <0x51>;
+ vref-supply = <®_ext_3v3_ref>;
+ };
+
+ /* TI ADC101C027 */
+ adc at 52 {
+ compatible = "ti,adc101c";
+ reg = <0x52>;
+ vref-supply = <®_ext_3v3_ref>;
+ };
+
+ /* Microchip 24AA025E48T-I/OT containing MAC for DHCOM ETH2 */
+ eeprom at 53 {
+ compatible = "atmel,24c02";
+ reg = <0x53>;
+ pagesize = <16>;
+ };
+};
+
+/* DHCOM I2C1 */
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-0 = <&pinctrl_i2c2>;
+ pinctrl-1 = <&pinctrl_i2c2_gpio>;
+ pinctrl-names = "default", "gpio";
+ scl-gpios = <&gpio1 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+};
+
+&lcdif {
+ pinctrl-0 = <&pinctrl_lcdif>;
+ pinctrl-names = "default";
+};
+
+&pwm1 {
+ pinctrl-0 = <&pinctrl_pwm1>;
+ pinctrl-names = "default";
+};
+
+&sai2 {
+ assigned-clock-rates = <320000000>;
+ assigned-clocks = <&clks IMX6UL_CLK_PLL3_PFD2>;
+ pinctrl-0 = <&pinctrl_sai2>;
+ pinctrl-names = "default";
+};
+
+&tsc {
+ measure-delay-time = <0xffff>;
+ pinctrl-0 = <&pinctrl_tsc>;
+ pinctrl-names = "default";
+ pre-charge-time = <0xfff>;
+ touchscreen-average-samples = <32>;
+ xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+};
+
+/* DHCOM UART1 */
+&uart1 {
+ pinctrl-0 = <&pinctrl_uart1>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+/*
+ * DHCOM UART2 (alternative)
+ * Special hardware required that uses DHCOM GPIO pins for DHCOM UART2.
+ * Therefore this UART interface can only be used if DHCOM GPIOs J/K/L/M are
+ * removed from GPIO hog muxing.
+ */
+&uart6 {
+ pinctrl-0 = <&pinctrl_uart6>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+};
+
+&usbotg1 {
+ adp-disable;
+ disable-over-current;
+ dr_mode = "otg";
+ hnp-disable;
+ pinctrl-0 = <&pinctrl_usbotg1>;
+ pinctrl-names = "default";
+ srp-disable;
+ vbus-supply = <®_usb_otg1_vbus>;
+ status = "okay";
+};
+
+&usbotg2 {
+ disable-over-current; /* Overcurrent pin is used for TSC */
+ dr_mode = "host";
+ pinctrl-0 = <&pinctrl_usbotg2>;
+ pinctrl-names = "default";
+ tpl-support;
+ vbus-supply = <®_usb_otg2_vbus>;
+ status = "okay";
+};
+
+&usbphy1 {
+ fsl,tx-d-cal = <106>;
+};
+
+&usbphy2 {
+ fsl,tx-d-cal = <106>;
+};
+
+/* WiFi on LGA */
+&usdhc1 {
+ mmc-pwrseq = <&usdhc1_pwrseq>;
+};
+
+/* eMMC on module */
+&usdhc2 {
+ bus-width = <8>;
+ no-1-8-v;
+ non-removable;
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-names = "default";
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+&iomuxc {
+ /* DHCOM GPIOs I..U + INT_HIGHEST_PRIORITY */
+ pinctrl_dhcom_i: dhcom-i-grp {
+ fsl,pins = <MX6UL_PAD_UART1_CTS_B__GPIO1_IO18 0x400120b0>;
+ };
+
+ pinctrl_dhcom_j: dhcom-j-grp {
+ fsl,pins = <MX6UL_PAD_CSI_HSYNC__GPIO4_IO20 0x400120b0>;
+ };
+
+ pinctrl_dhcom_k: dhcom-k-grp {
+ fsl,pins = <MX6UL_PAD_CSI_PIXCLK__GPIO4_IO18 0x400120b0>;
+ };
+
+ pinctrl_dhcom_l: dhcom-l-grp {
+ fsl,pins = <MX6UL_PAD_CSI_MCLK__GPIO4_IO17 0x400120b0>;
+ };
+
+ pinctrl_dhcom_m: dhcom-m-grp {
+ fsl,pins = <MX6UL_PAD_CSI_VSYNC__GPIO4_IO19 0x400120b0>;
+ };
+
+ pinctrl_dhcom_n: dhcom-n-grp {
+ fsl,pins = <MX6UL_PAD_CSI_DATA07__GPIO4_IO28 0x400120b0>;
+ };
+
+ pinctrl_dhcom_o: dhcom-o-grp {
+ fsl,pins = <MX6UL_PAD_CSI_DATA06__GPIO4_IO27 0x400120b0>;
+ };
+
+ pinctrl_dhcom_p: dhcom-p-grp {
+ fsl,pins = <MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x400120b0>;
+ };
+
+ pinctrl_dhcom_q: dhcom-q-grp {
+ fsl,pins = <MX6UL_PAD_CSI_DATA04__GPIO4_IO25 0x400120b0>;
+ };
+
+ pinctrl_dhcom_r: dhcom-r-grp {
+ fsl,pins = <MX6UL_PAD_CSI_DATA03__GPIO4_IO24 0x400120b0>;
+ };
+
+ pinctrl_dhcom_s: dhcom-s-grp {
+ fsl,pins = <MX6UL_PAD_CSI_DATA02__GPIO4_IO23 0x400120b0>;
+ };
+
+ pinctrl_dhcom_t: dhcom-t-grp {
+ fsl,pins = <MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x400120b0>;
+ };
+
+ pinctrl_dhcom_u: dhcom-u-grp {
+ fsl,pins = <MX6UL_PAD_CSI_DATA00__GPIO4_IO21 0x400120b0>;
+ };
+
+ pinctrl_dhcom_int: dhcom-int-grp {
+ fsl,pins = <MX6UL_PAD_JTAG_TMS__GPIO1_IO11 0x400120b0>;
+ };
+
+ pinctrl_ecspi1: ecspi1-grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA23__ECSPI1_MISO 0x100b1
+ MX6UL_PAD_LCD_DATA22__ECSPI1_MOSI 0x100b1
+ MX6UL_PAD_LCD_DATA20__ECSPI1_SCLK 0x100b1
+ MX6UL_PAD_LCD_DATA21__GPIO3_IO26 0x1b0b0 /* SS0 */
+ >;
+ };
+
+ pinctrl_ecspi4: ecspi4-grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET2_TX_CLK__ECSPI4_MISO 0x100b1
+ MX6UL_PAD_ENET2_TX_EN__ECSPI4_MOSI 0x100b1
+ MX6UL_PAD_ENET2_TX_DATA1__ECSPI4_SCLK 0x100b1
+ MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15 0x1b0b0 /* SS0 */
+ >;
+ };
+
+ pinctrl_fec1: fec1-grp {
+ fsl,pins = <
+ /* FEC1 uses MDIO bus from FEC2 */
+ MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b010
+ MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b010
+ MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b010
+ MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b010
+ >;
+ };
+
+ pinctrl_fec1_phy: fec1-phy-grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA18__GPIO3_IO23 0xb0 /* SMSC PHY reset */
+ >;
+ };
+
+ pinctrl_fec2: fec2-grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0
+ MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b010
+ MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b010
+ MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b010
+ MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b010
+ >;
+ };
+
+ pinctrl_fec2_phy: fec2-phy-grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA19__GPIO3_IO24 0xb0 /* SMSC PHY reset */
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1-grp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x1b020
+ MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x1b020
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2-grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020
+ MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020
+ >;
+ };
+
+ pinctrl_i2c2: i2c2-grp {
+ fsl,pins = <
+ MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0
+ MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0
+ >;
+ };
+
+ pinctrl_i2c2_gpio: i2c2-gpio-grp {
+ fsl,pins = <
+ MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x4001b8b0
+ MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31 0x4001b8b0
+ >;
+ };
+
+ pinctrl_lcdif: lcdif-grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79
+ MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79
+ MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x79
+ MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x79
+ MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x79
+ MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x79
+ MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79
+ MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79
+ MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79
+ MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79
+ MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79
+ MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79
+ MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x79
+ MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x79
+ MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79
+ MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79
+ MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79
+ MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79
+ MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79
+ MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79
+ MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x79
+ MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79
+ >;
+ };
+
+ pinctrl_pwm1: pwm1-grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO08__PWM1_OUT 0x110b0
+ >;
+ };
+
+ pinctrl_sai2: sai2-grp {
+ fsl,pins = <
+ MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x130b0
+ MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x17088
+ MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x17088
+ MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x120b0
+ >;
+ };
+
+ pinctrl_tsc: tsc-grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0xb0
+ MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0
+ MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0
+ MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0xb0
+ >;
+ };
+
+ pinctrl_uart1: uart1-grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart6: uart6-grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_MCLK__UART6_DCE_TX 0x1b0b1
+ MX6UL_PAD_CSI_PIXCLK__UART6_DCE_RX 0x1b0b1
+ MX6UL_PAD_CSI_VSYNC__UART6_DCE_RTS 0x1b0b1
+ MX6UL_PAD_CSI_HSYNC__UART6_DCE_CTS 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg1: usbotg1-grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x17059
+ >;
+ };
+
+ pinctrl_usbotg2: usbotg2-grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO05__GPIO1_IO05 0x120b0
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2-grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10069
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x17059
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x17059
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x17059
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x17059
+ MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x17059 /* SD2 Reset */
+ >;
+ };
+};
+
+&iomuxc_snvs {
+ /* DHCOM GPIOs A..H */
+ pinctrl_snvs_dhcom_a: snvs-dhcom-a-grp {
+ fsl,pins = <MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x400120b0>;
+ };
+
+ pinctrl_snvs_dhcom_b: snvs-dhcom-b-grp {
+ fsl,pins = <MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x400120b0>;
+ };
+
+ pinctrl_snvs_dhcom_c: snvs-dhcom-c-grp {
+ fsl,pins = <MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x400120b0>;
+ };
+
+ pinctrl_snvs_dhcom_d: snvs-dhcom-d-grp {
+ fsl,pins = <MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x400120b0>;
+ };
+
+ pinctrl_snvs_dhcom_e: snvs-dhcom-e-grp {
+ fsl,pins = <MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x400120b0>;
+ };
+
+ pinctrl_snvs_dhcom_f: snvs-dhcom-f-grp {
+ fsl,pins = <MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x400120b0>;
+ };
+
+ pinctrl_snvs_dhcom_g: snvs-dhcom-g-grp {
+ fsl,pins = <MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x400120b0>;
+ };
+
+ pinctrl_snvs_dhcom_h: snvs-dhcom-h-grp {
+ fsl,pins = <MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x400120b0>;
+ };
+
+ pinctrl_snvs_fec1_phy: snvs-fec1-phy-grp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05 0xb1 /* SMSC PHY Int */
+ >;
+ };
+
+ pinctrl_snvs_fec2_phy: snvs-fec2-phy-grp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06 0xb1 /* SMSC PHY Int */
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6ull-dhcor-som.dtsi b/arch/arm/boot/dts/imx6ull-dhcor-som.dtsi
new file mode 100644
index 000000000000..5882c7565f64
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-dhcor-som.dtsi
@@ -0,0 +1,255 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2023 DH electronics GmbH
+ */
+
+#include <dt-bindings/clock/imx6ul-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
+#include "imx6ull.dtsi"
+
+/ {
+ memory at 80000000 {
+ /* Appropriate memory size will be filled by U-Boot */
+ reg = <0x80000000 0>;
+ device_type = "memory";
+ };
+};
+
+&cpu0 {
+ /*
+ * Due to the design as a solderable SOM, there are no capacitors
+ * below the SoC, therefore higher voltages are required.
+ */
+ operating-points = <
+ /* kHz uV */
+ 900000 1275000
+ 792000 1250000 /* Voltage increased */
+ 528000 1175000
+ 396000 1025000
+ 198000 950000
+ >;
+ fsl,soc-operating-points = <
+ /* KHz uV */
+ 900000 1250000
+ 792000 1250000 /* Voltage increased */
+ 528000 1175000
+ 396000 1175000
+ 198000 1175000
+ >;
+};
+
+&gpio1 {
+ pinctrl-0 = <&pinctrl_spi1_switch>;
+ pinctrl-names = "default";
+ /*
+ * Pin SPI_BOOT_FLASH_EN (GPIO 1.9) is a switch for either using the
+ * DHCOM SPI1 interface or accessing the SPI bootflash. Both using
+ * ecspi1, but muxed to different pins. The DHCOM SPI1 interface uses
+ * the pins PAD_LCD_DATA21..23 and the SPI bootflash uses the pins
+ * PAD_CSI_DATA04..07. If the SPI bootflash is enabled the pins for
+ * DHCOM GPIOs N/O/P/Q/R/S/T/U aren't usable anymore, because they
+ * are used for the bus interface to the SPI bootflash. The GPIOs are
+ * disconnected by a buffer which is also controlled via the pin
+ * SPI_BOOT_FLASH_EN. Therefore the access to the bootflash is a
+ * special case and is disabled by setting GPIO 1.9 to high.
+ */
+ spi1-switch-hog {
+ gpio-hog;
+ gpios = <9 0>;
+ output-high;
+ line-name = "spi1-switch";
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-0 = <&pinctrl_i2c1>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ pinctrl-names = "default", "gpio";
+ scl-gpios = <&gpio1 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio1 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+
+ pmic at 58 {
+ compatible = "dlg,da9061";
+ reg = <0x58>;
+
+ onkey {
+ compatible = "dlg,da9061-onkey", "dlg,da9062-onkey";
+ status = "disabled";
+ };
+
+ regulators {
+ vdd_soc_in_1v4: buck1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <1400000>;
+ regulator-min-microvolt = <1400000>;
+ regulator-name = "vdd_soc_in_1v4";
+ };
+
+ vcc_3v3: buck2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "vcc_3v3";
+ };
+
+ /*
+ * The current DRR3 memory can be supplied with a
+ * voltage of either 1.35V or 1.5V. For reasons of
+ * backward compatibility to only 1.5V DDR3 memory,
+ * the voltage is set to 1.5V.
+ */
+ vcc_ddr_1v35: buck3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <1500000>;
+ regulator-min-microvolt = <1500000>;
+ regulator-name = "vcc_ddr_1v35";
+ };
+
+ vcc_2v5: ldo1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <2500000>;
+ regulator-min-microvolt = <2500000>;
+ regulator-name = "vcc_2v5";
+ };
+
+ vdd_snvs_in_3v3: ldo2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "vdd_snvs_in_3v3";
+ };
+
+ vcc_1v8: ldo3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <1800000>;
+ regulator-min-microvolt = <1800000>;
+ regulator-name = "vcc_1v8";
+ };
+
+ vcc_1v2: ldo4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <1200000>;
+ regulator-min-microvolt = <1200000>;
+ regulator-name = "vcc_1v2";
+ };
+ };
+
+ thermal {
+ compatible = "dlg,da9061-thermal", "dlg,da9062-thermal";
+ status = "disabled";
+ };
+
+ watchdog {
+ compatible = "dlg,da9061-watchdog", "dlg,da9062-watchdog";
+ status = "disabled";
+ };
+ };
+};
+
+&ocotp {
+ /* Don't get write access by default */
+ read-only;
+};
+
+®_arm {
+ vin-supply = <&vdd_soc_in_1v4>;
+};
+
+®_soc {
+ vin-supply = <&vdd_soc_in_1v4>;
+};
+
+/* BT on LGA (BT_REG_ON is connected to LGA pin E1) */
+&uart2 {
+ pinctrl-0 = <&pinctrl_uart2>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+ status = "okay";
+
+ /*
+ * Actually, the maximum speed of the chip is 4MBdps, but there are
+ * limitations that prevent this speed. It hasn't yet been figured out
+ * what the reason for this is. Currently, the maximum speed of 3MBdps
+ * can be used without any problems. If the limitation can be overcome,
+ * the speed can be increased accordingly.
+ */
+ bluetooth: bluetooth {
+ compatible = "brcm,bcm43430a1-bt"; /* muRata 1DX */
+ max-speed = <3000000>;
+ vbat-supply = <&vcc_3v3>;
+ vddio-supply = <&vcc_3v3>;
+ };
+};
+
+/* WiFi on LGA (WL_REG_ON is connected to LGA pin E3) */
+&usdhc1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ bus-width = <4>;
+ no-1-8-v;
+ non-removable;
+ keep-power-in-suspend;
+ pinctrl-0 = <&pinctrl_usdhc1_wifi>;
+ pinctrl-names = "default";
+ wakeup-source;
+ status = "okay";
+
+ brcmf: wifi at 1 {
+ compatible = "brcm,bcm43430a1-fmac", "brcm,bcm4329-fmac"; /* muRata 1DX */
+ reg = <1>;
+ };
+};
+
+&iomuxc {
+ pinctrl_i2c1: i2c1-grp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
+ MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0
+ >;
+ };
+
+ pinctrl_i2c1_gpio: i2c1-gpio-grp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x4001b8b0
+ MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x4001b8b0
+ >;
+ };
+
+ pinctrl_spi1_switch: spi1-switch-grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO09__GPIO1_IO09 0x120b0 /* SPI_BOOT_FLASH_EN */
+ >;
+ };
+
+ pinctrl_uart2: uart2-grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x1b0b1
+ MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS 0x1b0b1
+ MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc1_wifi: usdhc1-wifi-grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x1b0b0
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10010
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x1b0b0
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x1b0b0
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x1b0b0
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x1b0b0
+ >;
+ };
+};
--
2.11.0
More information about the linux-arm-kernel
mailing list