[PATCH v3] remoteproc: imx_dsp_rproc: add module parameter to ignore ready flag from remote processor

[Mathieu Poirier]

Hi Iuliana,

On Tue, Jan 17, 2023 at 01:03:57PM +0200, Iuliana Prodan (OSS) wrote:
> From: Iuliana Prodan <iuliana.prodan at nxp.com>
> 
> There are cases when we want to test a simple "hello world"
> application on the DSP and we don't have IPC between the cores.
> Therefore, skip the wait for remote processor to start.
> 
> Added "ignore_dsp_ready" flag while inserting the module to ignore
> remote processor reply after start.
> By default, this is off - do not ignore reply from rproc.
> 
> Signed-off-by: Iuliana Prodan <iuliana.prodan at nxp.com>
> 
> ---
> Changes since v2
> - s/ignoreready/ignore_dsp_ready
> 
> Changes since v1
> - change BIT(31) to BIT(1) for REMOTE_SKIP_WAIT
> 
> ---
>  drivers/remoteproc/imx_dsp_rproc.c | 17 +++++++++++++++++
>  1 file changed, 17 insertions(+)
> 
> diff --git a/drivers/remoteproc/imx_dsp_rproc.c b/drivers/remoteproc/imx_dsp_rproc.c
> index 95da1cbefacf..22e2ef068c67 100644
> --- a/drivers/remoteproc/imx_dsp_rproc.c
> +++ b/drivers/remoteproc/imx_dsp_rproc.c
> @@ -26,9 +26,20 @@
>  #include "remoteproc_elf_helpers.h"
>  #include "remoteproc_internal.h"
>  
> +#define IMX_DSP_IGNORE_REMOTE_READY		0
> +
> +/*
> + * Module parameters
> + */
> +static unsigned int imx_dsp_rproc_ignore_ready = IMX_DSP_IGNORE_REMOTE_READY;

Static variables are initialised to '0' and as such this is not needed.

> +module_param_named(ignore_dsp_ready, imx_dsp_rproc_ignore_ready, int, 0644);
> +MODULE_PARM_DESC(ignore_dsp_ready,
> +		 "Ignore remote proc reply after start, default is 0 (off).");
> +
>  #define DSP_RPROC_CLK_MAX			5
>  
>  #define REMOTE_IS_READY				BIT(0)
> +#define REMOTE_SKIP_WAIT			BIT(1)
>  #define REMOTE_READY_WAIT_MAX_RETRIES		500
>  
>  /* att flags */
> @@ -285,6 +296,9 @@ static int imx_dsp_rproc_ready(struct rproc *rproc)
>  	if (!priv->rxdb_ch)
>  		return 0;
>  
> +	if (priv->flags & REMOTE_SKIP_WAIT)
> +		return 0;
> +

This looks very hackish to me...

Here priv->rxdb_ch is valid and as such the DB mailbox has been setup, which
contradicts the commit log where it is stated that "we don't have IPC between
cores".  Moreover, the commit log mentions to "skip the wait for remote
processor to start".  How can the remote processor executed an sample
application if it is not ready?

Lastly, is there even a need to call imx_dsp_rproc_mbox_init() if an IPC is not
needed?

I'm fine with the module parameter but would much rather see a solution that
does not configure any kind of IPC related mechanic when it is not needed.

Thanks,
Mathieu

>  	for (i = 0; i < REMOTE_READY_WAIT_MAX_RETRIES; i++) {
>  		if (priv->flags & REMOTE_IS_READY)
>  			return 0;
> @@ -903,6 +917,9 @@ static int imx_dsp_rproc_probe(struct platform_device *pdev)
>  	priv->rproc = rproc;
>  	priv->dsp_dcfg = dsp_dcfg;
>  
> +	if (imx_dsp_rproc_ignore_ready)
> +		priv->flags |= REMOTE_SKIP_WAIT;
> +
>  	dev_set_drvdata(dev, rproc);
>  
>  	INIT_WORK(&priv->rproc_work, imx_dsp_rproc_vq_work);
> -- 
> 2.17.1
>