[PATCH 2/2] arm64: dts: imx8mp-verdin-dev: Do not include dahlia dtsi

[Philippe Schenker]

From: Philippe Schenker <philippe.schenker at toradex.com>

Follow the change that has been done on imx8mm-verdin-dev.dtsi and
remove the include from dahlia to be consistent. Put back all nodes that
previously had been included.

Signed-off-by: Philippe Schenker <philippe.schenker at toradex.com>

---

 .../boot/dts/freescale/imx8mp-verdin-dev.dtsi | 116 +++++++++++++++++-
 1 file changed, 114 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi
index cefabe65b252..361426c0da0a 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi
@@ -3,8 +3,6 @@
  * Copyright 2022 Toradex
  */
 
-#include "imx8mp-verdin-dahlia.dtsi"
-
 / {
 	/* TODO: Audio Codec */
 
@@ -21,16 +19,99 @@ reg_eth2phy: regulator-eth2phy {
 	};
 };
 
+&backlight {
+	power-supply = <&reg_3p3v>;
+};
+
+/* Verdin SPI_1 */
+&ecspi1 {
+	status = "okay";
+};
+
+/* EEPROM on display adapter boards */
+&eeprom_display_adapter {
+	status = "okay";
+};
+
+/* EEPROM on Verdin Development board */
+&eeprom_carrier_board {
+	status = "okay";
+};
+
+&eqos {
+	status = "okay";
+};
+
 &fec {
 	phy-supply = <&reg_eth2phy>;
 	status = "okay";
 };
 
+&flexcan1 {
+	status = "okay";
+};
+
+&flexcan2 {
+	status = "okay";
+};
+
+/* Verdin QSPI_1 */
+&flexspi {
+	status = "okay";
+};
+
 &gpio_expander_21 {
 	status = "okay";
 	vcc-supply = <&reg_1p8v>;
 };
 
+/* Current measurement into module VCC */
+&hwmon {
+	status = "okay";
+};
+
+&hwmon_temp {
+	vs-supply = <&reg_1p8v>;
+	status = "okay";
+};
+
+/* Verdin I2C_2_DSI */
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+/* Verdin I2C_1 */
+&i2c4 {
+	status = "okay";
+
+	/* TODO: Audio Codec */
+};
+
+/* TODO: Verdin PCIE_1 */
+
+/* Verdin PWM_1 */
+&pwm1 {
+	status = "okay";
+};
+
+/* Verdin PWM_2 */
+&pwm2 {
+	status = "okay";
+};
+
+/* Verdin PWM_3_DSI */
+&pwm3 {
+	status = "okay";
+};
+
+&reg_usdhc2_vmmc {
+	vin-supply = <&reg_3p3v>;
+};
+
 /* TODO: Verdin I2C_1 with Audio Codec */
 
 /* Verdin UART_1, connector X50 through RS485 transceiver */
@@ -38,9 +119,40 @@ &uart1 {
 	linux,rs485-enabled-at-boot-time;
 	rs485-rts-active-low;
 	rs485-rx-during-tx;
+	status = "okay";
+};
+
+/* Verdin UART_2 */
+&uart2 {
+	status = "okay";
+};
+
+/* Verdin UART_3, used as the Linux Console */
+&uart3 {
+	status = "okay";
+};
+
+/* Verdin USB_1 */
+&usb3_0 {
+	status = "okay";
+};
+
+&usb3_phy0 {
+	status = "okay";
+};
+
+/* Verdin USB_2 */
+&usb3_1 {
+	fsl,permanently-attached;
+	status = "okay";
+};
+
+&usb3_phy1 {
+	status = "okay";
 };
 
 /* Limit frequency on dev board due to long traces and bad signal integrity */
 &usdhc2 {
 	max-frequency = <100000000>;
+	status = "okay";
 };
-- 
2.39.0