[PATCH v3 1/1] dt-bindings: pinctrl: Update pinctrl-single to use yaml
Tony Lindgren
tony at atomide.com
Sun Jan 15 23:15:59 PST 2023
Update binding for yaml and remove the old related txt bindings. Note that
we are also adding the undocumented pinctrl-single,slew-rate property. And
we only use the first example from the old binding.
Cc: Nishanth Menon <nm at ti.com>
Cc: Vignesh Raghavendra <vigneshr at ti.com>
Signed-off-by: Tony Lindgren <tony at atomide.com>
---
Changes since v2:
- Drop old ti,omap-pinctrl.txt in addition to old pinctrl-single.txt
- Replace reference to pinctrl-single.txt to point to the yaml in ctrl.txt
Changes since v1:
- The v1 version was a WIP patch posted as an example in thread
"dt binding check error with hash and comma"
---
.../devicetree/bindings/arm/omap/ctrl.txt | 2 +-
.../bindings/pinctrl/pinctrl-single.txt | 262 ------------------
.../bindings/pinctrl/pinctrl-single.yaml | 155 +++++++++++
.../bindings/pinctrl/ti,omap-pinctrl.txt | 13 -
4 files changed, 156 insertions(+), 276 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
create mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-single.yaml
delete mode 100644 Documentation/devicetree/bindings/pinctrl/ti,omap-pinctrl.txt
diff --git a/Documentation/devicetree/bindings/arm/omap/ctrl.txt b/Documentation/devicetree/bindings/arm/omap/ctrl.txt
--- a/Documentation/devicetree/bindings/arm/omap/ctrl.txt
+++ b/Documentation/devicetree/bindings/arm/omap/ctrl.txt
@@ -8,7 +8,7 @@ control module driver itself.
See [2] for documentation about clock/clockdomain nodes.
-[1] Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
+[1] Documentation/devicetree/bindings/pinctrl/pinctrl-single.yaml
[2] Documentation/devicetree/bindings/clock/ti/*
Required properties:
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
deleted file mode 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
+++ /dev/null
@@ -1,262 +0,0 @@
-One-register-per-pin type device tree based pinctrl driver
-
-Required properties:
-- compatible : "pinctrl-single" or "pinconf-single".
- "pinctrl-single" means that pinconf isn't supported.
- "pinconf-single" means that generic pinconf is supported.
-
-- reg : offset and length of the register set for the mux registers
-
-- #pinctrl-cells : number of cells in addition to the index, set to 1
- or 2 for pinctrl-single,pins and set to 2 for pinctrl-single,bits
-
-- pinctrl-single,register-width : pinmux register access width in bits
-
-- pinctrl-single,function-mask : mask of allowed pinmux function bits
- in the pinmux register
-
-Optional properties:
-- pinctrl-single,function-off : function off mode for disabled state if
- available and same for all registers; if not specified, disabling of
- pin functions is ignored
-
-- pinctrl-single,bit-per-mux : boolean to indicate that one register controls
- more than one pin, for which "pinctrl-single,function-mask" property specifies
- position mask of pin.
-
-- pinctrl-single,drive-strength : array of value that are used to configure
- drive strength in the pinmux register. They're value of drive strength
- current and drive strength mask.
-
- /* drive strength current, mask */
- pinctrl-single,power-source = <0x30 0xf0>;
-
-- pinctrl-single,bias-pullup : array of value that are used to configure the
- input bias pullup in the pinmux register.
-
- /* input, enabled pullup bits, disabled pullup bits, mask */
- pinctrl-single,bias-pullup = <0 1 0 1>;
-
-- pinctrl-single,bias-pulldown : array of value that are used to configure the
- input bias pulldown in the pinmux register.
-
- /* input, enabled pulldown bits, disabled pulldown bits, mask */
- pinctrl-single,bias-pulldown = <2 2 0 2>;
-
- * Two bits to control input bias pullup and pulldown: User should use
- pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. One bit means
- pullup, and the other one bit means pulldown.
- * Three bits to control input bias enable, pullup and pulldown. User should
- use pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. Input bias
- enable bit should be included in pullup or pulldown bits.
- * Although driver could set PIN_CONFIG_BIAS_DISABLE, there's no property as
- pinctrl-single,bias-disable. Because pinctrl single driver could implement
- it by calling pulldown, pullup disabled.
-
-- pinctrl-single,input-schmitt : array of value that are used to configure
- input schmitt in the pinmux register. In some silicons, there're two input
- schmitt value (rising-edge & falling-edge) in the pinmux register.
-
- /* input schmitt value, mask */
- pinctrl-single,input-schmitt = <0x30 0x70>;
-
-- pinctrl-single,input-schmitt-enable : array of value that are used to
- configure input schmitt enable or disable in the pinmux register.
-
- /* input, enable bits, disable bits, mask */
- pinctrl-single,input-schmitt-enable = <0x30 0x40 0 0x70>;
-
-- pinctrl-single,low-power-mode : array of value that are used to configure
- low power mode of this pin. For some silicons, the low power mode will
- control the output of the pin when the pad including the pin enter low
- power mode.
- /* low power mode value, mask */
- pinctrl-single,low-power-mode = <0x288 0x388>;
-
-- pinctrl-single,gpio-range : list of value that are used to configure a GPIO
- range. They're value of subnode phandle, pin base in pinctrl device, pin
- number in this range, GPIO function value of this GPIO range.
- The number of parameters is depend on #pinctrl-single,gpio-range-cells
- property.
-
- /* pin base, nr pins & gpio function */
- pinctrl-single,gpio-range = <&range 0 3 0>, <&range 3 9 1>;
-
-- interrupt-controller : standard interrupt controller binding if using
- interrupts for wake-up events for example. In this case pinctrl-single
- is set up as a chained interrupt controller and the wake-up interrupts
- can be requested by the drivers using request_irq().
-
-- #interrupt-cells : standard interrupt binding if using interrupts
-
-This driver assumes that there is only one register for each pin (unless the
-pinctrl-single,bit-per-mux is set), and uses the common pinctrl bindings as
-specified in the pinctrl-bindings.txt document in this directory.
-
-The pin configuration nodes for pinctrl-single are specified as pinctrl
-register offset and values using pinctrl-single,pins. Only the bits specified
-in pinctrl-single,function-mask are updated.
-
-When #pinctrl-cells = 1, then setting a pin for a device could be done with:
-
- pinctrl-single,pins = <0xdc 0x118>;
-
-Where 0xdc is the offset from the pinctrl register base address for the device
-pinctrl register, and 0x118 contains the desired value of the pinctrl register.
-
-When #pinctrl-cells = 2, then setting a pin for a device could be done with:
-
- pinctrl-single,pins = <0xdc 0x30 0x07>;
-
-Where 0x30 is the pin configuration value and 0x07 is the pin mux mode value.
-These two values are OR'd together to produce the value stored at offset 0xdc.
-See the device example and static board pins example below for more information.
-
-In case when one register changes more than one pin's mux the
-pinctrl-single,bits need to be used which takes three parameters:
-
- pinctrl-single,bits = <0xdc 0x18 0xff>;
-
-Where 0xdc is the offset from the pinctrl register base address for the
-device pinctrl register, 0x18 is the desired value, and 0xff is the sub mask to
-be used when applying this change to the register.
-
-
-Optional sub-node: In case some pins could be configured as GPIO in the pinmux
-register, those pins could be defined as a GPIO range. This sub-node is required
-by pinctrl-single,gpio-range property.
-
-Required properties in sub-node:
-- #pinctrl-single,gpio-range-cells : the number of parameters after phandle in
- pinctrl-single,gpio-range property.
-
- range: gpio-range {
- #pinctrl-single,gpio-range-cells = <3>;
- };
-
-
-Example:
-
-/* SoC common file */
-
-/* first controller instance for pins in core domain */
-pmx_core: pinmux at 4a100040 {
- compatible = "pinctrl-single";
- reg = <0x4a100040 0x0196>;
- #address-cells = <1>;
- #size-cells = <0>;
- #interrupt-cells = <1>;
- interrupt-controller;
- pinctrl-single,register-width = <16>;
- pinctrl-single,function-mask = <0xffff>;
-};
-
-/* second controller instance for pins in wkup domain */
-pmx_wkup: pinmux at 4a31e040 {
- compatible = "pinctrl-single";
- reg = <0x4a31e040 0x0038>;
- #address-cells = <1>;
- #size-cells = <0>;
- #interrupt-cells = <1>;
- interrupt-controller;
- pinctrl-single,register-width = <16>;
- pinctrl-single,function-mask = <0xffff>;
-};
-
-control_devconf0: pinmux at 48002274 {
- compatible = "pinctrl-single";
- reg = <0x48002274 4>; /* Single register */
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-single,bit-per-mux;
- pinctrl-single,register-width = <32>;
- pinctrl-single,function-mask = <0x5F>;
-};
-
-/* third controller instance for pins in gpio domain */
-pmx_gpio: pinmux at d401e000 {
- compatible = "pinconf-single";
- reg = <0xd401e000 0x0330>;
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- pinctrl-single,register-width = <32>;
- pinctrl-single,function-mask = <7>;
-
- /* sparse GPIO range could be supported */
- pinctrl-single,gpio-range = <&range 0 3 0>, <&range 3 9 1>,
- <&range 12 1 0>, <&range 13 29 1>,
- <&range 43 1 0>, <&range 44 49 1>,
- <&range 94 1 1>, <&range 96 2 1>;
-
- range: gpio-range {
- #pinctrl-single,gpio-range-cells = <3>;
- };
-};
-
-
-/* board specific .dts file */
-
-&pmx_core {
-
- /*
- * map all board specific static pins enabled by the pinctrl driver
- * itself during the boot (or just set them up in the bootloader)
- */
- pinctrl-names = "default";
- pinctrl-0 = <&board_pins>;
-
- board_pins: pinmux_board_pins {
- pinctrl-single,pins = <
- 0x6c 0xf
- 0x6e 0xf
- 0x70 0xf
- 0x72 0xf
- >;
- };
-
- uart0_pins: pinmux_uart0_pins {
- pinctrl-single,pins = <
- 0x208 0 /* UART0_RXD (IOCFG138) */
- 0x20c 0 /* UART0_TXD (IOCFG139) */
- >;
- pinctrl-single,bias-pulldown = <0 2 2>;
- pinctrl-single,bias-pullup = <0 1 1>;
- };
-
- /* map uart2 pins */
- uart2_pins: pinmux_uart2_pins {
- pinctrl-single,pins = <
- 0xd8 0x118
- 0xda 0
- 0xdc 0x118
- 0xde 0
- >;
- };
-};
-
-&control_devconf0 {
- mcbsp1_pins: pinmux_mcbsp1_pins {
- pinctrl-single,bits = <
- 0x00 0x18 0x18 /* FSR/CLKR signal from FSX/CLKX pin */
- >;
- };
-
- mcbsp2_clks_pins: pinmux_mcbsp2_clks_pins {
- pinctrl-single,bits = <
- 0x00 0x40 0x40 /* McBSP2 CLKS from McBSP_CLKS pin */
- >;
- };
-
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins>;
-};
-
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart2_pins>;
-};
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.yaml
new file mode 100644
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.yaml
@@ -0,0 +1,155 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/pinctrl-single.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: One-register-per-pin type device tree based pinctrl driver
+
+maintainers:
+ - Tony Lindgren <tony at atomide.com>
+
+description: |
+ This binding describes pinctrl devices that use one hardware register to
+ configure each pin.
+
+properties:
+ compatible:
+ oneOf:
+ - items:
+ - enum:
+ - pinctrl-single
+ - pinconf-single
+ - items:
+ - enum:
+ - ti,am437-padconf
+ - ti,dra7-padconf
+ - ti,omap2420-padconf
+ - ti,omap2430-padconf
+ - ti,omap3-padconf
+ - ti,omap4-padconf
+ - ti,omap5-padconf
+ - const: pinctrl-single
+
+ reg:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ const: 1
+
+ '#address-cells':
+ const: 1
+
+ '#size-cells':
+ const: 0
+
+ '#pinctrl-cells':
+ enum: [ 1, 2 ]
+
+ '#gpio-range-cells':
+ const: 3
+ description: No longer needed, may exist in older files for gpio-ranges
+ deprecated: true
+
+ pinctrl-single,bit-per-mux:
+ description: Optional flag to indicate register controls more than one pin
+ type: boolean
+
+ pinctrl-single,function-mask:
+ description: Mask of the allowed register bits
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ pinctrl-single,function-off:
+ description: Optional function off mode for disabled state
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ pinctrl-single,gpio-range:
+ description: Optional list of pin base, nr pins & gpio function
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+
+ '#pinctrl-single,gpio-range-cells':
+ const: 3
+ description: Number of gpio range cells
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ pinctrl-single,register-width:
+ description: Width of the pin register in bits
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+patternProperties:
+ '-pins((.*)?)$':
+ type: object
+ $ref: pinmux-node.yaml#
+
+ patternProperties:
+ pinctrl-single,pins:
+ description:
+ Array of pins as described in pinmux-node.yaml for pinctrl-pin-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+
+ pinctrl-single,bias-pullup:
+ description: Optional array of input, enabled pullup bits, disabled pullup bits, mask
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+
+ pinctrl-single,bias-pulldown:
+ description: Optional array of input, enabled pulldown bits, disabled pulldown bits, mask
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+
+ pinctrl-single,drive-strength:
+ description: Optional array of drive strength current and mask
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+
+ pinctrl-single,input-schmitt:
+ description: Optional array of input, enable bits, disable bits, mask
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+
+ pinctrl-single,low-power-mode:
+ description: Optional array of low power mode value, mask
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+
+ pinctrl-single,slew-rate:
+ description: Optional array of slew rate and mask values
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+
+ additionalProperties: false
+
+allOf:
+ - $ref: 'pinctrl.yaml#'
+
+required:
+ - compatible
+ - reg
+ - pinctrl-single,register-width
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/pinctrl/omap.h>
+
+ soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ pinmux at 4a100040 {
+ compatible = "pinctrl-single";
+ reg = <0x4a100040 0x0196>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #pinctrl-cells = <2>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ pinctrl-single,register-width = <16>;
+ pinctrl-single,function-mask = <0xffff>;
+
+ uart2-pins {
+ pinctrl-single,pins =
+ <0xd8 0x118>,
+ <0xda 0>,
+ <0xdc 0x118>,
+ <0xde 0>;
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/pinctrl/ti,omap-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/ti,omap-pinctrl.txt
deleted file mode 100644
--- a/Documentation/devicetree/bindings/pinctrl/ti,omap-pinctrl.txt
+++ /dev/null
@@ -1,13 +0,0 @@
-OMAP Pinctrl definitions
-
-Required properties:
-- compatible : Should be one of:
- "ti,omap2420-padconf" - OMAP2420 compatible pinctrl
- "ti,omap2430-padconf" - OMAP2430 compatible pinctrl
- "ti,omap3-padconf" - OMAP3 compatible pinctrl
- "ti,omap4-padconf" - OMAP4 compatible pinctrl
- "ti,omap5-padconf" - OMAP5 compatible pinctrl
- "ti,dra7-padconf" - DRA7 compatible pinctrl
- "ti,am437-padconf" - AM437x compatible pinctrl
-
-See Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt for further details.
--
2.39.0
More information about the linux-arm-kernel
mailing list