[PATCH 6/7] arm64: dts: Add ipq9574 SoC and AL02 board support
Devi Priya
quic_devipriy at quicinc.com
Fri Jan 13 05:34:49 PST 2023
On 1/11/2023 8:22 PM, Kathiravan Thirumoorthy wrote:
>
> On 1/11/2023 3:14 PM, Krzysztof Kozlowski wrote:
>> On 10/01/2023 13:13, devi priya wrote:
>>> From: POOVENDHAN SELVARAJ <quic_poovendh at quicinc.com>
>>>
>>> Add initial device tree support for Qualcomm IPQ9574 SoC
>>> and AL02 board
>>>
>>> Co-developed-by: Anusha Rao <quic_anusha at quicinc.com>
>>> Signed-off-by: Anusha Rao <quic_anusha at quicinc.com>
>>> Co-developed-by: devi priya <quic_devipriy at quicinc.com>
>>> Signed-off-by: devi priya <quic_devipriy at quicinc.com>
>>> Signed-off-by: POOVENDHAN SELVARAJ <quic_poovendh at quicinc.com>
>>> ---
>>> arch/arm64/boot/dts/qcom/Makefile | 1 +
>>> arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts | 69 ++++
>>> arch/arm64/boot/dts/qcom/ipq9574.dtsi | 318 +++++++++++++++++++
>>> 3 files changed, 388 insertions(+)
>>> create mode 100644 arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
>>> create mode 100644 arch/arm64/boot/dts/qcom/ipq9574.dtsi
>>>
>>> diff --git a/arch/arm64/boot/dts/qcom/Makefile
>>> b/arch/arm64/boot/dts/qcom/Makefile
>>> index 3e79496292e7..872c62028a0b 100644
>>> --- a/arch/arm64/boot/dts/qcom/Makefile
>>> +++ b/arch/arm64/boot/dts/qcom/Makefile
>>> @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb
>>> dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb
>>> dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c1.dtb
>>> dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c2.dtb
>>> +dtb-$(CONFIG_ARCH_QCOM) += ipq9574-al02-c7.dtb
>>> dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb
>>> dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb
>>> dtb-$(CONFIG_ARCH_QCOM) += msm8916-huawei-g7.dtb
>>> diff --git a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
>>> b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
>>> new file mode 100644
>>> index 000000000000..ae3c32f3e16a
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
>>> @@ -0,0 +1,69 @@
>>> +// SPDX-License-Identifier: GPL-2.0-only
>> Not dual licensed? Not BSD?
>>
>>> +/*
>>> + * IPQ9574 AL02-C7 board device tree source
>>> + *
>>> + * Copyright (c) 2020-2021 The Linux Foundation. All rights reserved.
>>> + * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights
>>> reserved.
>>> + */
>>> +
>>> +/dts-v1/;
>>> +
>>> +#include "ipq9574.dtsi"
>>> +
>>> +/ {
>>> + model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C7";
>>> + compatible = "qcom,ipq9574-ap-al02-c7", "qcom,ipq9574";
>>> + interrupt-parent = <&intc>;
> Can this be droppeed? since it is already part of DTSI.
Sure okay
>>> +
>>> + aliases {
>>> + serial0 = &blsp1_uart2;
>>> + };
>>> +
>>> + chosen {
>>> + stdout-path = "serial0:115200n8";
>>> + };
>>> +};
>>> +
>>> +&blsp1_uart2 {
>>> + pinctrl-0 = <&uart2_pins>;
>>> + pinctrl-names = "default";
>>> + status = "okay";
>>> +};
>>> +
>>> +&sdhc_1 {
>>> + pinctrl-0 = <&emmc_pins>;
>>> + pinctrl-names = "default";
>>> + status = "okay";
>>> +};
>>> +
>>> +&tlmm {
>>> + emmc_pins: emmc-state {
>>> + emmc-clk-pins {
>>> + pins = "gpio5";
>>> + function = "sdc_clk";
>>> + drive-strength = <8>;
>>> + bias-disable;
>>> + };
>>> + emmc-cmd-pins {
>>> + pins = "gpio4";
>>> + function = "sdc_cmd";
>>> + drive-strength = <8>;
>>> + bias-pull-up;
>>> + };
>>> + emmc-data-pins {
>>> + pins = "gpio0", "gpio1", "gpio2",
>>> + "gpio3", "gpio6", "gpio7",
>>> + "gpio8", "gpio9";
>>> + function = "sdc_data";
>>> + drive-strength = <8>;
>>> + bias-pull-up;
>>> + };
>>> + emmc-rclk-pins {
>>> + pins = "gpio10";
>>> + function = "sdc_rclk";
>>> + drive-strength = <8>;
>>> + bias-pull-down;
>>> + };
>>> + };
>>> +
>>> +};
>>> diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>>> b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>>> new file mode 100644
>>> index 000000000000..188d18688a77
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>>> @@ -0,0 +1,318 @@
>>> +// SPDX-License-Identifier: GPL-2.0-only
>>> +/*
>>> + * IPQ9574 SoC device tree source
>>> + *
>>> + * Copyright (c) 2020-2021 The Linux Foundation. All rights reserved.
>>> + * Copyright (c) 2022, Qualcomm Innovation Center, Inc. All rights
>>> reserved.
>>> + */
>>> +
>>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>>> +#include <dt-bindings/clock/qcom,gcc-ipq9574.h>
>>> +#include <dt-bindings/reset/qcom,gcc-ipq9574.h>
>>> +
>>> +/ {
>>> + interrupt-parent = <&intc>;
>>> + #address-cells = <2>;
>>> + #size-cells = <2>;
>>> +
>>> + clocks {
>>> + bias_pll_ubi_nc_clk: bias_pll_ubi_nc_clk {
>> No undercores in node names.
>>
>>> + compatible = "fixed-clock";
>>> + clock-frequency = <353000000>;
>>> + #clock-cells = <0>;
>>> + };
>>> +
>>> + pcie30_phy0_pipe_clk: pcie30_phy0_pipe_clk {
>>> + compatible = "fixed-clock";
>>> + clock-frequency = <250000000>;
>>> + #clock-cells = <0>;
>>> + };
>>> +
>>> + pcie30_phy1_pipe_clk: pcie30_phy1_pipe_clk {
>>> + compatible = "fixed-clock";
>>> + clock-frequency = <250000000>;
>>> + #clock-cells = <0>;
>>> + };
>>> +
>>> + pcie30_phy2_pipe_clk: pcie30_phy2_pipe_clk {
>>> + compatible = "fixed-clock";
>>> + clock-frequency = <250000000>;
>>> + #clock-cells = <0>;
>>> + };
>>> +
>>> + pcie30_phy3_pipe_clk: pcie30_phy3_pipe_clk {
>>> + compatible = "fixed-clock";
>>> + clock-frequency = <250000000>;
>>> + #clock-cells = <0>;
>>> + };
>>> +
>>> + usb3phy_0_cc_pipe_clk: usb3phy_0_cc_pipe_clk {
>>> + compatible = "fixed-clock";
>>> + clock-frequency = <125000000>;
>>> + #clock-cells = <0>;
>>> + };
>>> +
>>> + sleep_clk: sleep-clk {
>>> + compatible = "fixed-clock";
>>> + clock-frequency = <32000>;
>> That's not a property of the SoC, but board. Either entire clock or at
>> least frequency to indicate that the board is providing the clock.
>>
>>> + #clock-cells = <0>;> + };
>>> +
>>> + xo_board_clk: xo-board-clk {
>>> + compatible = "fixed-clock";
>>> + clock-frequency = <24000000>;
>> Ditto.
>>
>>> + #clock-cells = <0>;
>>> + };
>>> + };
>>> +
>>> + cpus {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + CPU0: cpu at 0 {
>>> + device_type = "cpu";
>>> + compatible = "arm,cortex-a73";
>>> + reg = <0x0>;
>>> + enable-method = "psci";
>>> + next-level-cache = <&L2_0>;
>>> + };
>>> +
>>> + CPU1: cpu at 1 {
>>> + device_type = "cpu";
>>> + compatible = "arm,cortex-a73";
>>> + reg = <0x1>;
>>> + enable-method = "psci";
>>> + next-level-cache = <&L2_0>;
>>> + };
>>> +
>>> + CPU2: cpu at 2 {
>>> + device_type = "cpu";
>>> + compatible = "arm,cortex-a73";
>>> + reg = <0x2>;
>>> + enable-method = "psci";
>>> + next-level-cache = <&L2_0>;
>>> + };
>>> +
>>> + CPU3: cpu at 3 {
>>> + device_type = "cpu";
>>> + compatible = "arm,cortex-a73";
>>> + reg = <0x3>;
>>> + enable-method = "psci";
>>> + next-level-cache = <&L2_0>;
>>> + };
>>> +
>>> + L2_0: l2-cache {
>>> + compatible = "cache";
>>> + cache-level = <2>;
>>> + };
>>> + };
>>> +
>>> + memory at 40000000 {
>>> + device_type = "memory";
>>> + /* We expect the bootloader to fill in the size */
>>> + reg = <0x0 0x40000000 0x0 0x0>;
>>> + };
>>> +
>>> + pmu {
>>> + compatible = "arm,cortex-a73-pmu";
>>> + interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) |
>>> IRQ_TYPE_LEVEL_HIGH)>;
>>> + };
>>> +
>>> + psci {
>>> + compatible = "arm,psci-1.0";
>>> + method = "smc";
>>> + };
>>> +
>>> + reserved-memory {
>>> + #address-cells = <2>;
>>> + #size-cells = <2>;
>>> + ranges;
>>> +
>>> + tz_region: memory at 4a600000 {
>>> + reg = <0x0 0x4a600000 0x0 0x400000>;
>>> + no-map;
>>> + };
>>> + };
>>> +
>>> + soc: soc at 0 {
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>>> + ranges = <0 0 0 0xffffffff>;
>>> + compatible = "simple-bus";
>>> +
>>> + tlmm: pinctrl at 1000000 {
>>> + compatible = "qcom,ipq9574-tlmm";
>>> + reg = <0x01000000 0x300000>;
>>> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
>>> + gpio-controller;
>>> + #gpio-cells = <2>;
>>> + gpio-ranges = <&tlmm 0 0 65>;
>>> + gpio-reserved-ranges = <59 1>;
>> Hm, why reserved ranges are in SoC?
>>
>>> + interrupt-controller;
>>> + #interrupt-cells = <2>;
>>> +
>>> + uart2_pins: uart2-state {
>>> + pins = "gpio34", "gpio35";
>>> + function = "blsp2_uart";
>>> + drive-strength = <8>;
>>> + bias-disable;
>>> + };
>>> + };
>>> +
>>> + gcc: clock-controller at 1800000 {
>>> + compatible = "qcom,gcc-ipq9574";
>>> + reg = <0x1800000 0x80000>;
> Address can be padded to 8-hex-digits. Please take care of this in all
> nodes.
Sure, will do
>>> + clocks = <&xo_board_clk>,
>>> + <&sleep_clk>,
>>> + <&bias_pll_ubi_nc_clk>,
>>> + <&pcie30_phy0_pipe_clk>,
>>> + <&pcie30_phy1_pipe_clk>,
>>> + <&pcie30_phy2_pipe_clk>,
>>> + <&pcie30_phy3_pipe_clk>,
>>> + <&usb3phy_0_cc_pipe_clk>;
>>> + clock-names = "xo",
>>> + "sleep_clk",
>> Misaligned. Multiple other places probably as well.
>>
>>> + "bias_pll_ubi_nc_clk",
>>> + "pcie30_phy0_pipe_clk",
>>> + "pcie30_phy1_pipe_clk",
>>> + "pcie30_phy2_pipe_clk",
>>> + "pcie30_phy3_pipe_clk",
>>> + "usb3phy_0_cc_pipe_clk";
>>> + #clock-cells = <1>;
>>> + #reset-cells = <1>;
>>> + };
>>> +
>>> + sdhc_1: sdhci at 7804000 {
>>> + compatible = "qcom,sdhci-msm-v5";
>>> + reg = <0x7804000 0x1000>, <0x7805000 0x1000>;
>>> + reg-names = "hc_mem", "cmdq_mem";
>>> +
>>> + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
>>> + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
>> Like here.
>>
>>> + interrupt-names = "hc_irq", "pwr_irq";
>>> +
>>> + clocks = <&xo_board_clk>,
>>> + <&gcc GCC_SDCC1_AHB_CLK>,
>>> + <&gcc GCC_SDCC1_APPS_CLK>;
>> And here
>>
>>> + clock-names = "xo", "iface", "core";
>> Does not look like you tested the bindings. Please run `make
>> dt_binding_check` (see
>> Documentation/devicetree/bindings/writing-schema.rst for instructions).
>>
>>> + mmc-ddr-1_8v;
>>> + mmc-hs200-1_8v;
>>> + mmc-hs400-1_8v;
>>> + mmc-hs400-enhanced-strobe;
>>> + max-frequency = <384000000>;
>>> + bus-width = <8>;
>>> + non-removable;
>>> + status = "disabled";
>>> + };
>>> +
>>> + blsp1_uart2: serial at 78b1000 {
>>> + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
>>> + reg = <0x078b1000 0x200>;
>>> + interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>;
>>> + clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>,
>>> + <&gcc GCC_BLSP1_AHB_CLK>;
>>> + clock-names = "core", "iface";
>>> + status = "disabled";
>>> + };
>>> +
>>> + intc: interrupt-controller at b000000 {
>>> + compatible = "qcom,msm-qgic2";
>>> + reg = <0x0b000000 0x1000>, /* GICD */
>>> + <0x0b002000 0x1000>, /* GICC */
>>> + <0x0b001000 0x1000>, /* GICH */
>>> + <0x0b004000 0x1000>; /* GICV */
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>>> + interrupt-controller;
>>> + #interrupt-cells = <3>;
>>> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
>>> + ranges = <0 0x0b00c000 0x3000>;
>>> +
>>> + v2m0: v2m at 0 {
>>> + compatible = "arm,gic-v2m-frame";
>>> + reg = <0x0 0xffd>;
>>> + msi-controller;
>>> + };
>>> +
>>> + v2m1: v2m at 1 {
>>> + compatible = "arm,gic-v2m-frame";
>>> + reg = <0x1000 0xffd>;
>>> + msi-controller;
>>> + };
>>> +
>>> + v2m2: v2m at 2 {
>>> + compatible = "arm,gic-v2m-frame";
>>> + reg = <0x2000 0xffd>;
>>> + msi-controller;
>>> + };
>>> + };
>>> +
>>> + timer at b120000 {
>>> + compatible = "arm,armv7-timer-mem";
>>> + reg = <0xb120000 0x1000>;
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>>> + ranges;
>>> + clock-frequency = <24000000>;
>>> +
>>> + frame at b120000 {
>>> + reg = <0xb121000 0x1000>,
>>> + <0xb122000 0x1000>;
>>> + frame-number = <0>;
>>> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
>>> + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
>>> + };
>>> +
>>> + frame at b123000 {
>>> + reg = <0xb123000 0x1000>;
>>> + frame-number = <1>;
>>> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
>>> + status = "disabled";
>>> + };
>>> +
>>> + frame at b124000 {
>>> + reg = <0xb124000 0x1000>;
>>> + frame-number = <2>;
>>> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
>>> + status = "disabled";
>>> + };
>>> +
>>> + frame at b125000 {
>>> + reg = <0xb125000 0x1000>;
>>> + frame-number = <3>;
>>> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
>>> + status = "disabled";
>>> + };
>>> +
>>> + frame at b126000 {
>>> + reg = <0xb126000 0x1000>;
>>> + frame-number = <4>;
>>> + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
>>> + status = "disabled";
>>> + };
>>> +
>>> + frame at b127000 {
>>> + reg = <0xb127000 0x1000>;
>>> + frame-number = <5>;
>>> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
>>> + status = "disabled";
>>> + };
>>> +
>>> + frame at b128000 {
>>> + reg = <0xb128000 0x1000>;
>>> + frame-number = <6>;
>>> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
>>> + status = "disabled";
>>> + };
>>> + };
>>> + };
>>> +
>>> + timer {
>>> + compatible = "arm,armv8-timer";
>>> + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) |
>>> IRQ_TYPE_LEVEL_LOW)>,
>>> + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) |
>>> IRQ_TYPE_LEVEL_LOW)>,
>>> + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) |
>>> IRQ_TYPE_LEVEL_LOW)>,
>>> + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) |
>>> IRQ_TYPE_LEVEL_LOW)>;
>>> + clock-frequency = <24000000>;
>> Is this allowed in recent designs?
>>
>>> + };
>>> +};
>> Best regards,
>> Krzysztof
>>
Best Regards,
Devi Priya
More information about the linux-arm-kernel
mailing list