[PATCH v4 3/3] arm64: dts: ti: k3-am625-sk: Add support for USB

[Sjoerd Simons]

From: Aswath Govindraju <a-govindraju at ti.com>

AM62 SoC has two instances of USB and they are brought on to the board
in the following way,

-> USB0 instance
 - This is brought out to a USB TypeC connector on board through TPS6598 PD
   controller. The PD controller should decide the role based on CC pin in
   the connector. Unfortunately the irq line for the TPS isn't hooked up
   which is a mode not yet support by the driver (some patches were
   submitted earlier this year[0]). So for now the PD controller is left
   out and peripheral mode chosen.

-> USB1 instance
 - This is brought out to a USB TypeA connector on board.

Therefore, add the required device tree support for the above in the board
dts file.

0: https://lore.kernel.org/lkml/f714ee55-ef47-317d-81b9-57020dda064b@ti.com/T/

Signed-off-by: Aswath Govindraju <a-govindraju at ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr at ti.com>
[merge from vendor bsp, drop TPS6598 support, drop unneeded nodes, reword commit message]
Signed-off-by: Sjoerd Simons <sjoerd at collabora.com>
Tested-by: Martyn Welch <martyn.welch at collabora.com>

---

Changes in v4:
- Disable new usbss nodes by default in the dtsi and enable in the dts
- Drop unneeded disabled nodes in board dts
- Drop unneeded nodes
- Enable usbss nodes
- Small typo fix

Changes in v3:
- Rebased against current ti-next aka 6.2-rc1
- Add Martyn's tested-by

Changes in v2:
- Rebase against linux-next 20221220

 arch/arm64/boot/dts/ti/k3-am625-sk.dts | 27 ++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
index 4f179b146cab..6bc7d63cf52f 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
@@ -24,6 +24,8 @@ aliases {
 		spi0 = &ospi0;
 		ethernet0 = &cpsw_port1;
 		ethernet1 = &cpsw_port2;
+		usb0 = &usb0;
+		usb1 = &usb1;
 	};
 
 	chosen {
@@ -284,6 +286,12 @@ main_gpio1_ioexp_intr_pins_default: main-gpio1-ioexp-intr-pins-default {
 			AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
 		>;
 	};
+
+	main_usb1_pins_default: main-usb1-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0258, PIN_OUTPUT, 0) /* (F18) USB1_DRVVBUS */
+		>;
+	};
 };
 
 &wkup_uart0 {
@@ -464,3 +472,22 @@ partition at 3fc0000 {
 		};
 	};
 };
+
+&usbss0 {
+	status = "okay";
+	ti,vbus-divider;
+};
+
+&usbss1 {
+	status = "okay";
+};
+
+&usb0 {
+	dr_mode = "peripheral";
+};
+
+&usb1 {
+	dr_mode = "host";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_usb1_pins_default>;
+};
-- 
2.39.0