[PATCH v7 2/4] arm64: dts: qcom: sc8280xp-crd: Enable EDP

[Konrad Dybcio]

On 11.01.2023 04:59, Bjorn Andersson wrote:
> From: Bjorn Andersson <bjorn.andersson at linaro.org>
> 
> The SC8280XP CRD has a EDP display on MDSS0 DP3, enable relevant nodes
> and link it together with the backlight control.
> 
> Signed-off-by: Bjorn Andersson <bjorn.andersson at linaro.org>
> Signed-off-by: Bjorn Andersson <quic_bjorande at quicinc.com>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio at linaro.org>

Konrad
> 
> Changes since v6:
> - None
> 
>  arch/arm64/boot/dts/qcom/sc8280xp-crd.dts | 73 ++++++++++++++++++++++-
>  1 file changed, 72 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
> index 551768f97729..db12d8678861 100644
> --- a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
> +++ b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
> @@ -20,7 +20,7 @@ aliases {
>  		serial0 = &qup2_uart17;
>  	};
>  
> -	backlight {
> +	backlight: backlight {
>  		compatible = "pwm-backlight";
>  		pwms = <&pmc8280c_lpg 3 1000000>;
>  		enable-gpios = <&pmc8280_1_gpios 8 GPIO_ACTIVE_HIGH>;
> @@ -34,6 +34,22 @@ chosen {
>  		stdout-path = "serial0:115200n8";
>  	};
>  
> +	vreg_edp_3p3: regulator-edp-3p3 {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "VREG_EDP_3P3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +
> +		gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&edp_reg_en>;
> +
> +		regulator-boot-on;
> +	};
> +
>  	vreg_edp_bl: regulator-edp-bl {
>  		compatible = "regulator-fixed";
>  
> @@ -228,6 +244,55 @@ vreg_l9d: ldo9 {
>  	};
>  };
>  
> +&dispcc0 {
> +	status = "okay";
> +};
> +
> +&mdss0 {
> +	status = "okay";
> +};
> +
> +&mdss0_dp3 {
> +	compatible = "qcom,sc8280xp-edp";
> +
> +	data-lanes = <0 1 2 3>;
> +
> +	status = "okay";
> +
> +	aux-bus {
> +		panel {
> +			compatible = "edp-panel";
> +			power-supply = <&vreg_edp_3p3>;
> +
> +			backlight = <&backlight>;
> +
> +			ports {
> +				port {
> +					edp_panel_in: endpoint {
> +						remote-endpoint = <&mdss0_dp3_out>;
> +					};
> +				};
> +			};
> +		};
> +	};
> +
> +	ports {
> +		port at 1 {
> +			reg = <1>;
> +			mdss0_dp3_out: endpoint {
> +				remote-endpoint = <&edp_panel_in>;
> +			};
> +		};
> +	};
> +};
> +
> +&mdss0_dp3_phy {
> +	vdda-phy-supply = <&vreg_l6b>;
> +	vdda-pll-supply = <&vreg_l3b>;
> +
> +	status = "okay";
> +};
> +
>  &pcie2a {
>  	perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
>  	wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
> @@ -494,6 +559,12 @@ hastings_reg_en: hastings-reg-en-state {
>  &tlmm {
>  	gpio-reserved-ranges = <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
>  
> +	edp_reg_en: edp-reg-en-state {
> +		pins = "gpio25";
> +		function = "gpio";
> +		drive-strength = <16>;
> +	};
> +
>  	kybd_default: kybd-default-state {
>  		disable-pins {
>  			pins = "gpio102";