[PATCH v6 1/2] dt-bindings: i2c: aspeed: support for AST2600-i2cv2

Ryan Chen ryan_chen at aspeedtech.com
Tue Feb 28 19:40:54 PST 2023


Hello Jeremy,

> -----Original Message-----
> From: Jeremy Kerr <jk at codeconstruct.com.au>
> Sent: Wednesday, March 1, 2023 11:24 AM
> To: Ryan Chen <ryan_chen at aspeedtech.com>; Andrew Jeffery
> <andrew at aj.id.au>; Brendan Higgins <brendan.higgins at linux.dev>; Benjamin
> Herrenschmidt <benh at kernel.crashing.org>; Joel Stanley <joel at jms.id.au>;
> Rob Herring <robh+dt at kernel.org>; Krzysztof Kozlowski
> <krzysztof.kozlowski+dt at linaro.org>; Philipp Zabel <p.zabel at pengutronix.de>;
> linux-i2c at vger.kernel.org; openbmc at lists.ozlabs.org;
> devicetree at vger.kernel.org; linux-arm-kernel at lists.infradead.org;
> linux-aspeed at lists.ozlabs.org; linux-kernel at vger.kernel.org
> Subject: Re: [PATCH v6 1/2] dt-bindings: i2c: aspeed: support for AST2600-i2cv2
> 
> Hi Ryan,
> 
> > Sorry, Do you mean add in description like following??
> >   aspeed,xfer-mode:
> >     description: |
> >       I2C bus transfer mode selection.
> >           ERRATA "I2C DMA fails when DRAM bus is busy and it can
> not
> > take DMA write data Immediately", only 1 i2c bus can be enable for DMA
> > mode.
> >       - "byte": I2C bus byte transfer mode.
> >       - "buffered": I2C bus buffer register transfer mode.
> >       - "dma": I2C bus dma transfer mode (default)
> 
> I would suggest putting some background about the transfer mode as a
> top-level description in the binding.
> 
> There has been a lot of discussion here on why the binding specifies the
> transfer mode; it would be useful (for future readers) to have a bit of context
> on what modes they should use.
> 
> Perhaps something like:
> 
>     description: |
>       [general binding description]
> 
>       ASPEED ast2600 platforms have a number of i2c controllers, and share
> a
>       single DMA engine between the set. DTSes can specify the mode of
> data
>       transfer to/from the device - either DMA or programmed I/O - but
>       hardware limitations may require a DTS to manually allocate which
>       controller can use DMA mode; the enable-dma property allows control
> of
>       this.
> 
>       In cases where one the hardware design results in a specific
>       controller handling a larger amount of data, a DTS would likely
>       allocate DMA mode for that one controller.
> 
> - adjusted for whatever property interface we settle on here, of course.
> 
It is more clear now, I will add in next patch.

> > > So, it sounds like:
> > >
> > >  - there's no point in using byte mode, as buffer mode provides
> > >    equivalent functionality with fewer drawbacks (ie, less interrupt
> > >    load)
> > >
> > >  - this just leaves the dma and buffer modes
> > >
> > >  - only one controller can use dma mode
> > >
> > > So: how about just a single boolean property to indicate "use DMA on
> > > this controller"? Something like aspeed,enable-dma? Or if DT binding
> > > experts can suggest something common that might be more suitable?
> >
> > If so, just leave enable-dma and only support for buffer mode and dma
> > mode, am I right?
> 
> Yes, from what you have said so far, I think just a single switch between DMA /
> not-DMA is all you need here (unless there is any time that byte mode is
> preferable?)

Yes, I also think so, but if I only for dma to be single Boolean property.
Should I remove all byte mode capability in driver?

Best Regards.
Ryan

> If there is already an existing DT convention for indicating/enabling DMA
> capability, I would suggest using that. Otherwise, just a boolean flag with a
> sensible name would seem to work fine. The DT experts probably have a good
> idea of what works best here :)
> 
> Cheers,
> 
> 
> Jeremy


More information about the linux-arm-kernel mailing list