[PATCH net-next V6] dt-bindings: net: xlnx,axi-ethernet: convert bindings document to yaml

[Rob Herring]

On Mon, Feb 20, 2023 at 05:52:52PM +0530, Sarath Babu Naidu Gaddam wrote:
> From: Radhey Shyam Pandey <radhey.shyam.pandey at xilinx.com>
> 
> Convert the bindings document for Xilinx AXI Ethernet Subsystem
> from txt to yaml. No changes to existing binding description.
> 
> Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey at xilinx.com>
> Signed-off-by: Sarath Babu Naidu Gaddam <sarath.babu.naidu.gaddam at amd.com>
> ---
> Changes in V6:
> 1) Addressed below review comments.
> 	a)add a $ref to ethernet-controller.yaml for pcs-handle.
> 	b)Drop unused labels(axi_ethernetlite_0_mdio).
> 	c)Not relevant to the binding(interrupt-parent).
> 
> Changes in V5:
> 1) Removed .txt file which was missed in V4
> 
> Changes in V4:
> 1)Changed the interrupts property and add allOf:if:then for it.
> 
> Changes in V3:
> 1) Moved RFC to PATCH.
> 2) Addressed below review comments
> 	a) Indentation.
> 	b) maxItems:3 does not match your description.
> 	c) Filename matching compatibles.
> 
> Changes in V2:
> 1) remove .txt and change the name of file to xlnx,axiethernet.yaml.
> 2) Fix DT check warning('device_type' does not match any of the regexes:
>    'pinctrl-[0-9]+' From schema: Documentation/devicetree/bindings/net
>     /xilinx_axienet.yaml).
> ---
>  .../bindings/net/xilinx_axienet.txt           | 101 -----------
>  .../bindings/net/xlnx,axi-ethernet.yaml       | 165 ++++++++++++++++++
>  MAINTAINERS                                   |   1 +
>  3 files changed, 166 insertions(+), 101 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/net/xilinx_axienet.txt
>  create mode 100644 Documentation/devicetree/bindings/net/xlnx,axi-ethernet.yaml

[...]

> +++ b/Documentation/devicetree/bindings/net/xlnx,axi-ethernet.yaml
> @@ -0,0 +1,165 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/net/xlnx,axi-ethernet.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: AXI 1G/2.5G Ethernet Subsystem
> +
> +description: |
> +  Also called  AXI 1G/2.5G Ethernet Subsystem, the xilinx axi ethernet IP core
> +  provides connectivity to an external ethernet PHY supporting different
> +  interfaces: MII, GMII, RGMII, SGMII, 1000BaseX. It also includes two
> +  segments of memory for buffering TX and RX, as well as the capability of
> +  offloading TX/RX checksum calculation off the processor.
> +
> +  Management configuration is done through the AXI interface, while payload is
> +  sent and received through means of an AXI DMA controller. This driver
> +  includes the DMA driver code, so this driver is incompatible with AXI DMA
> +  driver.
> +
> +maintainers:
> +  - Radhey Shyam Pandey <radhey.shyam.pandey at xilinx.com>
> +
> +properties:
> +  compatible:
> +    enum:
> +      - xlnx,axi-ethernet-1.00.a
> +      - xlnx,axi-ethernet-1.01.a
> +      - xlnx,axi-ethernet-2.01.a
> +
> +  reg:
> +    description:
> +      Address and length of the IO space, as well as the address
> +      and length of the AXI DMA controller IO space, unless
> +      axistream-connected is specified, in which case the reg
> +      attribute of the node referenced by it is used.
> +    maxItems: 2
> +
> +  interrupts:
> +    items:
> +      - description: Ethernet core interrupt
> +      - description: Tx DMA interrupt
> +      - description: Rx DMA interrupt
> +    description:
> +      Ethernet core interrupt is optional. If axistream-connected property is
> +      present DMA node should contains TX/RX DMA interrupts else DMA interrupt
> +      resources are mentioned on ethernet node.
> +    minItems: 1
> +
> +  phy-handle: true
> +
> +  xlnx,rxmem:
> +    description:
> +      Set to allocated memory buffer for Rx/Tx in the hardware.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +
> +  phy-mode: true

I'd assume only a subset of modes are supported by this h/w. If so, list 
them.

> +
> +  xlnx,phy-type:
> +    description:
> +      Do not use, but still accepted in preference to phy-mode.
> +    deprecated: true
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +
> +  xlnx,txcsum:
> +    description:
> +      TX checksum offload. 0 or empty for disabling TX checksum offload,
> +      1 to enable partial TX checksum offload and 2 to enable full TX
> +      checksum offload.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [0, 1, 2]
> +
> +  xlnx,rxcsum:
> +    description:
> +      RX checksum offload. 0 or empty for disabling RX checksum offload,
> +      1 to enable partial RX checksum offload and 2 to enable full RX
> +      checksum offload.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [0, 1, 2]
> +
> +  xlnx,switch-x-sgmii:
> +    type: boolean
> +    description:
> +      Indicate the Ethernet core is configured to support both 1000BaseX and
> +      SGMII modes. If set, the phy-mode should be set to match the mode
> +      selected on core reset (i.e. by the basex_or_sgmii core input line).
> +
> +  clocks:
> +    items:
> +      - description: Clock for AXI register slave interface.
> +      - description: AXI4-Stream clock for TXD RXD TXC and RXS interfaces.
> +      - description: Ethernet reference clock, used by signal delay primitives
> +                     and transceivers.
> +      - description: MGT reference clock (used by optional internal PCS/PMA PHY)
> +
> +  clock-names:
> +    items:
> +      - const: s_axi_lite_clk
> +      - const: axis_clk
> +      - const: ref_clk
> +      - const: mgt_clk
> +
> +  axistream-connected:
> +    type: object
> +    description: Reference to another node which contains the resources

Reference? Meaning a phandle? Or this is a node because that's what 
'type: object' says.

> +      for the AXI DMA controller used by this device. If this is specified,
> +      the DMA-related resources from that device (DMA registers and DMA
> +      TX/RX interrupts) rather than this one will be used.
> +
> +  mdio: true

type: object

> +
> +  pcs-handle:
> +    description: Phandle to the internal PCS/PMA PHY in SGMII or 1000Base-X
> +      modes, where "pcs-handle" should be used to point to the PCS/PMA PHY,
> +      and "phy-handle" should point to an external PHY if exists.
> +    $ref: /schemas/net/ethernet-controller.yaml#

The reference applies to nodes, but 'pcs-handle' is a property. It needs 
to be at the top-level:

allOf:
  - $ref: /schemas/net/ethernet-controller.yaml#

Rob