[PATCH v10 00/26] Drivers for Gunyah hypervisor
Alex Elder
alex.elder at linaro.org
Thu Feb 23 13:59:58 PST 2023
On 2/14/23 3:12 PM, Elliot Berman wrote:
> Gunyah is a Type-1 hypervisor independent of any
> high-level OS kernel, and runs in a higher CPU privilege level. It does
> not depend on any lower-privileged OS kernel/code for its core
> functionality. This increases its security and can support a much smaller
> trusted computing base than a Type-2 hypervisor.
Very general comment, across your whole series...
Although it is not strictly required any more, most kernel
code still stays within about 80 columns width, where longer
lines are the exception. Your patches go beyond 80 columns
a lot, and it's just not what I'm accustomed to looking at.
Others might disagree with this, but it would be my preference
that you try to reformat your lines so they normally fit within
80 columns. Format strings for printk-like functions are an
exception--people prefer those to be kept intact. But even
there, look at long messages and consider whether they can
be made more concise.
-Alex
> Gunyah is an open source hypervisor. The source repo is available at
> https://github.com/quic/gunyah-hypervisor.
>
> The diagram below shows the architecture.
>
> ::
>
> VM A VM B
> +-----+ +-----+ | +-----+ +-----+ +-----+
> | | | | | | | | | | |
> EL0 | APP | | APP | | | APP | | APP | | APP |
> | | | | | | | | | | |
> +-----+ +-----+ | +-----+ +-----+ +-----+
> ---------------------|-------------------------
> +--------------+ | +----------------------+
> | | | | |
> EL1 | Linux Kernel | | |Linux kernel/Other OS | ...
> | | | | |
> +--------------+ | +----------------------+
> --------hvc/smc------|------hvc/smc------------
> +----------------------------------------+
> | |
> EL2 | Gunyah Hypervisor |
> | |
> +----------------------------------------+
>
> Gunyah provides these following features.
>
> - Threads and Scheduling: The scheduler schedules virtual CPUs (VCPUs) on
> physical CPUs and enables time-sharing of the CPUs.
> - Memory Management: Gunyah tracks memory ownership and use of all memory
> under its control. Memory partitioning between VMs is a fundamental
> security feature.
> - Interrupt Virtualization: All interrupts are handled in the hypervisor
> and routed to the assigned VM.
> - Inter-VM Communication: There are several different mechanisms provided
> for communicating between VMs.
> - Device Virtualization: Para-virtualization of devices is supported using
> inter-VM communication. Low level system features and devices such as
> interrupt controllers are supported with emulation where required.
>
> This series adds the basic framework for detecting that Linux is running
> under Gunyah as a virtual machine, communication with the Gunyah Resource
> Manager, and a virtual machine manager capable of launching virtual machines.
>
> The series relies on two other patches posted separately:
> - https://lore.kernel.org/all/20230213181832.3489174-1-quic_eberman@quicinc.com/
> - https://lore.kernel.org/all/20230213232537.2040976-2-quic_eberman@quicinc.com/
>
> Changes in v10:
> - Fix bisectability (end result of series is same, --fixups applied to wrong commits)
> - Convert GH_ERROR_* and GH_RM_ERROR_* to enums
> - Correct race condition between allocating/freeing user memory
> - Replace offsetof with struct_size
> - Series-wide renaming of functions to be more consistent
> - VM shutdown & restart support added in vCPU and VM Manager patches
> - Convert VM function name (string) to type (number)
> - Convert VM function argument to value (which could be a pointer) to remove memory wastage for arguments
> - Remove defensive checks of hypervisor correctness
> - Clean ups to ioeventfd as suggested by Srivatsa
>
> Changes in v9: https://lore.kernel.org/all/20230120224627.4053418-1-quic_eberman@quicinc.com/
> - Refactor Gunyah API flags to be exposed as feature flags at kernel level
> - Move mbox client cleanup into gunyah_msgq_remove()
> - Simplify gh_rm_call return value and response payload
> - Missing clean-up/error handling/little endian fixes as suggested by Srivatsa and Alex in v8 series
>
> Changes in v8: https://lore.kernel.org/all/20221219225850.2397345-1-quic_eberman@quicinc.com/
> - Treat VM manager as a library of RM
> - Add patches 21-28 as RFC to support proxy-scheduled vCPUs and necessary bits to support virtio
> from Gunyah userspace
>
> Changes in v7: https://lore.kernel.org/all/20221121140009.2353512-1-quic_eberman@quicinc.com/
> - Refactor to remove gunyah RM bus
> - Refactor allow multiple RM device instances
> - Bump UAPI to start at 0x0
> - Refactor QCOM SCM's platform hooks to allow CONFIG_QCOM_SCM=Y/CONFIG_GUNYAH=M combinations
>
> Changes in v6: https://lore.kernel.org/all/20221026185846.3983888-1-quic_eberman@quicinc.com/
> - *Replace gunyah-console with gunyah VM Manager*
> - Move include/asm-generic/gunyah.h into include/linux/gunyah.h
> - s/gunyah_msgq/gh_msgq/
> - Minor tweaks and documentation tidying based on comments from Jiri, Greg, Arnd, Dmitry, and Bagas.
>
> Changes in v5: https://lore.kernel.org/all/20221011000840.289033-1-quic_eberman@quicinc.com/
> - Dropped sysfs nodes
> - Switch from aux bus to Gunyah RM bus for the subdevices
> - Cleaning up RM console
>
> Changes in v4: https://lore.kernel.org/all/20220928195633.2348848-1-quic_eberman@quicinc.com/
> - Tidied up documentation throughout based on questions/feedback received
> - Switched message queue implementation to use mailboxes
> - Renamed "gunyah_device" as "gunyah_resource"
>
> Changes in v3: https://lore.kernel.org/all/20220811214107.1074343-1-quic_eberman@quicinc.com/
> - /Maintained/Supported/ in MAINTAINERS
> - Tidied up documentation throughout based on questions/feedback received
> - Moved hypercalls into arch/arm64/gunyah/; following hyper-v's implementation
> - Drop opaque typedefs
> - Move sysfs nodes under /sys/hypervisor/gunyah/
> - Moved Gunyah console driver to drivers/tty/
> - Reworked gunyah_device design to drop the Gunyah bus.
>
> Changes in v2: https://lore.kernel.org/all/20220801211240.597859-1-quic_eberman@quicinc.com/
> - DT bindings clean up
> - Switch hypercalls to follow SMCCC
>
> v1: https://lore.kernel.org/all/20220223233729.1571114-1-quic_eberman@quicinc.com/
>
> Elliot Berman (26):
> docs: gunyah: Introduce Gunyah Hypervisor
> dt-bindings: Add binding for gunyah hypervisor
> gunyah: Common types and error codes for Gunyah hypercalls
> virt: gunyah: Add hypercalls to identify Gunyah
> virt: gunyah: Identify hypervisor version
> virt: gunyah: msgq: Add hypercalls to send and receive messages
> mailbox: Add Gunyah message queue mailbox
> gunyah: rsc_mgr: Add resource manager RPC core
> gunyah: rsc_mgr: Add VM lifecycle RPC
> gunyah: vm_mgr: Introduce basic VM Manager
> gunyah: rsc_mgr: Add RPC for sharing memory
> unyah: vm_mgr: Add/remove user memory regions
> gunyah: vm_mgr: Add ioctls to support basic non-proxy VM boot
> samples: Add sample userspace Gunyah VM Manager
> gunyah: rsc_mgr: Add platform ops on mem_lend/mem_reclaim
> firmware: qcom_scm: Register Gunyah platform ops
> docs: gunyah: Document Gunyah VM Manager
> virt: gunyah: Translate gh_rm_hyp_resource into gunyah_resource
> gunyah: vm_mgr: Add framework to add VM Functions
> virt: gunyah: Add resource tickets
> virt: gunyah: Add IO handlers
> virt: gunyah: Add proxy-scheduled vCPUs
> virt: gunyah: Add hypercalls for sending doorbell
> virt: gunyah: Add irqfd interface
> virt: gunyah: Add ioeventfd
> MAINTAINERS: Add Gunyah hypervisor drivers section
>
> .../bindings/firmware/gunyah-hypervisor.yaml | 82 ++
> .../userspace-api/ioctl/ioctl-number.rst | 1 +
> Documentation/virt/gunyah/index.rst | 114 +++
> Documentation/virt/gunyah/message-queue.rst | 69 ++
> Documentation/virt/gunyah/vm-manager.rst | 193 +++++
> Documentation/virt/index.rst | 1 +
> MAINTAINERS | 13 +
> arch/arm64/Kbuild | 1 +
> arch/arm64/gunyah/Makefile | 3 +
> arch/arm64/gunyah/gunyah_hypercall.c | 146 ++++
> arch/arm64/include/asm/gunyah.h | 23 +
> drivers/firmware/Kconfig | 2 +
> drivers/firmware/qcom_scm.c | 100 +++
> drivers/mailbox/Makefile | 2 +
> drivers/mailbox/gunyah-msgq.c | 214 +++++
> drivers/virt/Kconfig | 2 +
> drivers/virt/Makefile | 1 +
> drivers/virt/gunyah/Kconfig | 46 +
> drivers/virt/gunyah/Makefile | 11 +
> drivers/virt/gunyah/gunyah.c | 54 ++
> drivers/virt/gunyah/gunyah_ioeventfd.c | 113 +++
> drivers/virt/gunyah/gunyah_irqfd.c | 160 ++++
> drivers/virt/gunyah/gunyah_platform_hooks.c | 80 ++
> drivers/virt/gunyah/gunyah_vcpu.c | 463 ++++++++++
> drivers/virt/gunyah/rsc_mgr.c | 798 +++++++++++++++++
> drivers/virt/gunyah/rsc_mgr.h | 169 ++++
> drivers/virt/gunyah/rsc_mgr_rpc.c | 419 +++++++++
> drivers/virt/gunyah/vm_mgr.c | 801 ++++++++++++++++++
> drivers/virt/gunyah/vm_mgr.h | 70 ++
> drivers/virt/gunyah/vm_mgr_mm.c | 258 ++++++
> include/linux/gunyah.h | 198 +++++
> include/linux/gunyah_rsc_mgr.h | 171 ++++
> include/linux/gunyah_vm_mgr.h | 119 +++
> include/uapi/linux/gunyah.h | 191 +++++
> samples/Kconfig | 10 +
> samples/Makefile | 1 +
> samples/gunyah/.gitignore | 2 +
> samples/gunyah/Makefile | 6 +
> samples/gunyah/gunyah_vmm.c | 270 ++++++
> samples/gunyah/sample_vm.dts | 68 ++
> 40 files changed, 5445 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/firmware/gunyah-hypervisor.yaml
> create mode 100644 Documentation/virt/gunyah/index.rst
> create mode 100644 Documentation/virt/gunyah/message-queue.rst
> create mode 100644 Documentation/virt/gunyah/vm-manager.rst
> create mode 100644 arch/arm64/gunyah/Makefile
> create mode 100644 arch/arm64/gunyah/gunyah_hypercall.c
> create mode 100644 arch/arm64/include/asm/gunyah.h
> create mode 100644 drivers/mailbox/gunyah-msgq.c
> create mode 100644 drivers/virt/gunyah/Kconfig
> create mode 100644 drivers/virt/gunyah/Makefile
> create mode 100644 drivers/virt/gunyah/gunyah.c
> create mode 100644 drivers/virt/gunyah/gunyah_ioeventfd.c
> create mode 100644 drivers/virt/gunyah/gunyah_irqfd.c
> create mode 100644 drivers/virt/gunyah/gunyah_platform_hooks.c
> create mode 100644 drivers/virt/gunyah/gunyah_vcpu.c
> create mode 100644 drivers/virt/gunyah/rsc_mgr.c
> create mode 100644 drivers/virt/gunyah/rsc_mgr.h
> create mode 100644 drivers/virt/gunyah/rsc_mgr_rpc.c
> create mode 100644 drivers/virt/gunyah/vm_mgr.c
> create mode 100644 drivers/virt/gunyah/vm_mgr.h
> create mode 100644 drivers/virt/gunyah/vm_mgr_mm.c
> create mode 100644 include/linux/gunyah.h
> create mode 100644 include/linux/gunyah_rsc_mgr.h
> create mode 100644 include/linux/gunyah_vm_mgr.h
> create mode 100644 include/uapi/linux/gunyah.h
> create mode 100644 samples/gunyah/.gitignore
> create mode 100644 samples/gunyah/Makefile
> create mode 100644 samples/gunyah/gunyah_vmm.c
> create mode 100644 samples/gunyah/sample_vm.dts
>
>
> base-commit: 3ebb0ac55efaf1d0fb1b106f852c114e5021f7eb
More information about the linux-arm-kernel
mailing list