[PATCH v3 2/4] arm64: dts: qcom: sc8280xp-crd: Introduce pmic_glink

[Konrad Dybcio]

On 13.02.2023 17:28, Bjorn Andersson wrote:
> From: Bjorn Andersson <bjorn.andersson at linaro.org>
> 
> The SC8280XP CRD control over battery management and its two USB Type-C
> port using pmic_glink and two GPIO-based SBU muxes.
> 
> Enable the two DisplayPort instances, GPIO SBU mux instance and
> pmic_glink with the two connectors on the CRD.
> 
> Signed-off-by: Bjorn Andersson <bjorn.andersson at linaro.org>
> Signed-off-by: Bjorn Andersson <quic_bjorande at quicinc.com>
> ---
> 
[...]

> +&mdss0_dp0 {
> +	data-lanes = <0 1>;
> +	status = "okay";
> +
> +	ports {
> +		port at 1 {
> +			reg = <1>;
> +
> +			mdss0_dp0_out: endpoint {
> +				remote-endpoint = <&pmic_glink_con0_ss>;
> +			};
> +		};
> +	};
> +};
> +
> +&mdss0_dp1 {
> +	data-lanes = <0 1>;
> +	status = "okay";
> +
> +	ports {
> +		port at 1 {
> +			reg = <1>;
This way you're redefining this node.. I suppose going with
something like:

8280:
mdss0_dp1 {
	compatible
	blahblah

	ports {
		[..]

		port at 1 {
		reg = <1>;

			mdss0_dp1_out : endpoint {
			};
		};
	}
}

crd:
&mdss0_dp1_out {
	//btw data-lanes should be there and not in mdss_dp, I think
	remote-endpoint = <&pmic_glink_...>
}

would be better, and that's what we're already doing for DSI..

I think I missed all this during the 8[34]50 review too..

With that addressed, for both crd and x13s (as the patch is essentially
identical)

Reviewed-by: Konrad Dybcio <konrad.dybcio at linaro.org>

Konrad

> +
> +			mdss0_dp1_out: endpoint {
> +				remote-endpoint = <&pmic_glink_con1_ss>;
> +			};
> +		};
> +	};
> +};
> +
>  &mdss0_dp3 {
>  	compatible = "qcom,sc8280xp-edp";
>  	/delete-property/ #sound-dai-cells;
> @@ -480,7 +628,6 @@ &usb_0 {
>  };
>  
>  &usb_0_dwc3 {
> -	/* TODO: Define USB-C connector properly */
>  	dr_mode = "host";
>  };
>  
> @@ -499,12 +646,15 @@ &usb_0_qmpphy {
>  	status = "okay";
>  };
>  
> +&usb_0_role_switch {
> +	remote-endpoint = <&pmic_glink_con0_hs>;
> +};
> +
>  &usb_1 {
>  	status = "okay";
>  };
>  
>  &usb_1_dwc3 {
> -	/* TODO: Define USB-C connector properly */
>  	dr_mode = "host";
>  };
>  
> @@ -523,6 +673,10 @@ &usb_1_qmpphy {
>  	status = "okay";
>  };
>  
> +&usb_1_role_switch {
> +	remote-endpoint = <&pmic_glink_con1_hs>;
> +};
> +
>  &xo_board_clk {
>  	clock-frequency = <38400000>;
>  };
> @@ -709,4 +863,54 @@ reset-n-pins {
>  			drive-strength = <16>;
>  		};
>  	};
> +
> +	usb0_sbu_default: usb0-sbu-state {
> +		oe-n-pins {
> +			pins = "gpio101";
> +			function = "gpio";
> +			bias-disable;
> +			drive-strengh = <16>;
> +			output-high;
> +		};
> +
> +		sel-pins {
> +			pins = "gpio164";
> +			function = "gpio";
> +			bias-disable;
> +			drive-strength = <16>;
> +		};
> +
> +		mode-pins {
> +			pins = "gpio167";
> +			function = "gpio";
> +			bias-disable;
> +			drive-strength = <16>;
> +			output-high;
> +		};
> +	};
> +
> +	usb1_sbu_default: usb1-sbu-state {
> +		oe-n-pins {
> +			pins = "gpio48";
> +			function = "gpio";
> +			bias-disable;
> +			drive-strengh = <16>;
> +			output-high;
> +		};
> +
> +		sel-pins {
> +			pins = "gpio47";
> +			function = "gpio";
> +			bias-disable;
> +			drive-strength = <16>;
> +		};
> +
> +		mode-pins {
> +			pins = "gpio50";
> +			function = "gpio";
> +			bias-disable;
> +			drive-strength = <16>;
> +			output-high;
> +		};
> +	};
>  };
> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> index 92d5b5e21e50..7897d33f1416 100644
> --- a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> @@ -3040,6 +3040,11 @@ usb_0_dwc3: usb at a600000 {
>  				iommus = <&apps_smmu 0x820 0x0>;
>  				phys = <&usb_0_hsphy>, <&usb_0_qmpphy QMP_USB43DP_USB3_PHY>;
>  				phy-names = "usb2-phy", "usb3-phy";
> +
> +				port {
> +					usb_0_role_switch: endpoint {
> +					};
> +				};
>  			};
>  		};
>  
> @@ -3095,6 +3100,11 @@ usb_1_dwc3: usb at a800000 {
>  				iommus = <&apps_smmu 0x860 0x0>;
>  				phys = <&usb_1_hsphy>, <&usb_1_qmpphy QMP_USB43DP_USB3_PHY>;
>  				phy-names = "usb2-phy", "usb3-phy";
> +
> +				port {
> +					usb_1_role_switch: endpoint {
> +					};
> +				};
>  			};
>  		};
>