[RFC PATCH 2/2] tee: Add op-tee helper functions for variable access
Jens Wiklander
jens.wiklander at linaro.org
Fri Feb 3 01:30:28 PST 2023
On Thu, Jan 26, 2023 at 10:21:19PM +0900, Masahisa Kojima wrote:
> When the flash is not owned by the non-secure world, accessing the EFI
> variables is straightforward and done via EFI Runtime Variable Services.
> In this case, critical variables for system integrity and security
> are normally stored in the dedicated secure storage and only accessible
> from the secure world.
>
> On the other hand, the small embedded devices don't have the special
> dedicated secure storage. The eMMC device with an RPMB partition is
> becoming more common, we can use an RPMB partition to store the
> EFI Variables.
>
> The eMMC device is typically owned by the non-secure world(linux in
> this case). There is an existing solution utilizing eMMC RPMB partition
> for EFI Variables, it is implemented by interacting with
> OP-TEE, StandaloneMM(as EFI Variable Service Pseudo TA), eMMC driver
> and tee-supplicant. The last piece is the tee-based variable access
> driver to interact with OP-TEE and StandaloneMM.
>
> So let's add the kernel functions needed.
>
> This feature is implemented as a kernel module.
> StMM PTA has TA_FLAG_DEVICE_ENUM_SUPP flag when registered to OP-TEE
> so that this optee_stmm_efi module is probed after tee-supplicant starts,
> since "SetVariable" EFI Runtime Variable Service requires to
> interact with tee-supplicant.
>
> Co-developed-by: Ilias Apalodimas <ilias.apalodimas at linaro.org>
> Signed-off-by: Ilias Apalodimas <ilias.apalodimas at linaro.org>
> Signed-off-by: Masahisa Kojima <masahisa.kojima at linaro.org>
> ---
> drivers/tee/optee/Kconfig | 10 +
> drivers/tee/optee/Makefile | 1 +
> drivers/tee/optee/mm_communication.h | 249 +++++++++++
> drivers/tee/optee/optee_private.h | 5 +-
> drivers/tee/optee/optee_stmm_efi.c | 598 +++++++++++++++++++++++++++
> drivers/tee/tee_core.c | 23 ++
> include/linux/efi.h | 1 +
> include/linux/tee_drv.h | 23 ++
> 8 files changed, 909 insertions(+), 1 deletion(-)
> create mode 100644 drivers/tee/optee/mm_communication.h
> create mode 100644 drivers/tee/optee/optee_stmm_efi.c
Please split this patch into three patches, one for drivers/tee, one
for the driver/tee/optee, and one for include/linux/efi.h.
>
> diff --git a/drivers/tee/optee/Kconfig b/drivers/tee/optee/Kconfig
> index f121c224e682..a0b699977e51 100644
> --- a/drivers/tee/optee/Kconfig
> +++ b/drivers/tee/optee/Kconfig
> @@ -7,3 +7,13 @@ config OPTEE
> help
> This implements the OP-TEE Trusted Execution Environment (TEE)
> driver.
> +
> +config EFI_STMM_OPTEE
Should this be OPTEE_EFI_STMM?
> + tristate "OP-TEE based EFI runtime variable service driver"
> + depends on OPTEE
> + help
> + This driver provides support for OP-TEE based EFI runtime
> + variable service driver.
> +
> + To compile this driver as a module, choose M here: the module
> + will be called optee_stmm_efi.
> diff --git a/drivers/tee/optee/Makefile b/drivers/tee/optee/Makefile
> index a6eff388d300..9acb0b2de8fe 100644
> --- a/drivers/tee/optee/Makefile
> +++ b/drivers/tee/optee/Makefile
> @@ -8,6 +8,7 @@ optee-objs += supp.o
> optee-objs += device.o
> optee-objs += smc_abi.o
> optee-objs += ffa_abi.o
> +obj-$(CONFIG_EFI_STMM_OPTEE) += optee_stmm_efi.o
>
> # for tracing framework to find optee_trace.h
> CFLAGS_smc_abi.o := -I$(src)
> diff --git a/drivers/tee/optee/mm_communication.h b/drivers/tee/optee/mm_communication.h
> new file mode 100644
> index 000000000000..23e6672991ef
> --- /dev/null
> +++ b/drivers/tee/optee/mm_communication.h
> @@ -0,0 +1,249 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * Headers for EFI variable service via StandAloneMM, EDK2 application running
> + * in OP-TEE
> + *
> + * Copyright (c) 2017, Intel Corporation. All rights reserved.
> + * Copyright (C) 2020 Linaro Ltd.
> + */
> +
> +#ifndef _MM_COMMUNICATION_H_
> +#define _MM_COMMUNICATION_H_
> +
> +/*
> + * Interface to the pseudo Trusted Application (TA), which provides a
> + * communication channel with the Standalone MM (Management Mode)
> + * Secure Partition running at Secure-EL0
> + */
> +
> +#define PTA_STMM_CMDID_COMMUNICATE 0
PTA_STMM_CMD_COMMUNICATE
> +
> +/* OP-TEE is using big endian GUIDs while UEFI uses little endian ones */
> +#define PTA_STMM_UUID \
> + UUID_INIT(0xed32d533, 0x99e6, 0x4209, \
> + 0x9c, 0xc0, 0x2d, 0x72, 0xcd, 0xd9, 0x98, 0xa7)
> +
> +#define EFI_MM_VARIABLE_GUID \
> + EFI_GUID(0xed32d533, 0x99e6, 0x4209, \
> + 0x9c, 0xc0, 0x2d, 0x72, 0xcd, 0xd9, 0x98, 0xa7)
> +
> +/* Defined in EDK2 MdePkg/Include/Protocol/MmCommunication.h */
> +
> +/**
> + * struct efi_mm_communicate_header - Header used for SMM variable communication
> +
> + * @header_guid: header use for disambiguation of content
> + * @message_len: length of the message. Does not include the size of the
> + * header
> + * @data: payload of the message
> + *
> + * Defined in EDK2 as EFI_MM_COMMUNICATE_HEADER.
> + * To avoid confusion in interpreting frames, the communication buffer should
> + * always begin with efi_mm_communicate_header.
> + */
> +struct efi_mm_communicate_header {
> + efi_guid_t header_guid;
> + size_t message_len;
> + u8 data[];
> +} __packed;
> +
> +#define MM_COMMUNICATE_HEADER_SIZE \
> + (sizeof(struct efi_mm_communicate_header))
> +
> +/* Defined in EDK2 ArmPkg/Include/IndustryStandard/ArmMmSvc.h */
> +
> +/* SPM return error codes */
> +#define ARM_SVC_SPM_RET_SUCCESS 0
> +#define ARM_SVC_SPM_RET_NOT_SUPPORTED -1
> +#define ARM_SVC_SPM_RET_INVALID_PARAMS -2
> +#define ARM_SVC_SPM_RET_DENIED -3
> +#define ARM_SVC_SPM_RET_NO_MEMORY -5
> +
> +/* Defined in EDK2 MdeModulePkg/Include/Guid/SmmVariableCommon.h */
> +
> +#define SMM_VARIABLE_FUNCTION_GET_VARIABLE 1
> +/*
> + * The payload for this function is
> + * SMM_VARIABLE_COMMUNICATE_GET_NEXT_VARIABLE_NAME.
> + */
> +#define SMM_VARIABLE_FUNCTION_GET_NEXT_VARIABLE_NAME 2
> +/*
> + * The payload for this function is SMM_VARIABLE_COMMUNICATE_ACCESS_VARIABLE.
> + */
> +#define SMM_VARIABLE_FUNCTION_SET_VARIABLE 3
> +/*
> + * The payload for this function is
> + * SMM_VARIABLE_COMMUNICATE_QUERY_VARIABLE_INFO.
> + */
> +#define SMM_VARIABLE_FUNCTION_QUERY_VARIABLE_INFO 4
> +/*
> + * It is a notify event, no extra payload for this function.
> + */
> +#define SMM_VARIABLE_FUNCTION_READY_TO_BOOT 5
> +/*
> + * It is a notify event, no extra payload for this function.
> + */
> +#define SMM_VARIABLE_FUNCTION_EXIT_BOOT_SERVICE 6
> +/*
> + * The payload for this function is VARIABLE_INFO_ENTRY.
> + * The GUID in EFI_SMM_COMMUNICATE_HEADER is gEfiSmmVariableProtocolGuid.
> + */
> +#define SMM_VARIABLE_FUNCTION_GET_STATISTICS 7
> +/*
> + * The payload for this function is SMM_VARIABLE_COMMUNICATE_LOCK_VARIABLE
> + */
> +#define SMM_VARIABLE_FUNCTION_LOCK_VARIABLE 8
> +
> +#define SMM_VARIABLE_FUNCTION_VAR_CHECK_VARIABLE_PROPERTY_SET 9
> +
> +#define SMM_VARIABLE_FUNCTION_VAR_CHECK_VARIABLE_PROPERTY_GET 10
> +
> +#define SMM_VARIABLE_FUNCTION_GET_PAYLOAD_SIZE 11
> +/*
> + * The payload for this function is
> + * SMM_VARIABLE_COMMUNICATE_RUNTIME_VARIABLE_CACHE_CONTEXT
> + */
> +#define SMM_VARIABLE_FUNCTION_INIT_RUNTIME_VARIABLE_CACHE_CONTEXT 12
> +
> +#define SMM_VARIABLE_FUNCTION_SYNC_RUNTIME_CACHE 13
> +/*
> + * The payload for this function is
> + * SMM_VARIABLE_COMMUNICATE_GET_RUNTIME_CACHE_INFO
> + */
> +#define SMM_VARIABLE_FUNCTION_GET_RUNTIME_CACHE_INFO 14
> +
> +/**
> + * struct smm_variable_communicate_header - Used for SMM variable communication
> +
> + * @function: function to call in Smm.
> + * @ret_status: return status
> + * @data: payload
> + *
> + * Defined in EDK2 as SMM_VARIABLE_COMMUNICATE_HEADER.
> + */
> +struct smm_variable_communicate_header {
> + size_t function;
> + efi_status_t ret_status;
> + u8 data[];
> +};
> +
> +#define MM_VARIABLE_COMMUNICATE_SIZE \
> + (sizeof(struct smm_variable_communicate_header))
> +
> +/**
> + * struct smm_variable_access - Used to communicate with StMM by
> + * SetVariable and GetVariable.
> +
> + * @guid: vendor GUID
> + * @data_size: size of EFI variable data
> + * @name_size: size of EFI name
> + * @attr: attributes
> + * @name: variable name
> + *
> + * Defined in EDK2 as SMM_VARIABLE_COMMUNICATE_ACCESS_VARIABLE.
> + *
> + */
> +struct smm_variable_access {
> + efi_guid_t guid;
> + size_t data_size;
> + size_t name_size;
> + u32 attr;
> + u16 name[];
> +};
> +
> +#define MM_VARIABLE_ACCESS_HEADER_SIZE \
> + (sizeof(struct smm_variable_access))
> +/**
> + * struct smm_variable_payload_size - Used to get the max allowed
> + * payload used in StMM.
> + *
> + * @size: size to fill in
> + *
> + * Defined in EDK2 as SMM_VARIABLE_COMMUNICATE_GET_PAYLOAD_SIZE.
> + *
> + */
> +struct smm_variable_payload_size {
> + size_t size;
> +};
> +
> +/**
> + * struct smm_variable_getnext - Used to communicate with StMM for
> + * GetNextVariableName.
> + *
> + * @guid: vendor GUID
> + * @name_size: size of the name of the variable
> + * @name: variable name
> + *
> + * Defined in EDK2 as SMM_VARIABLE_COMMUNICATE_GET_NEXT_VARIABLE_NAME.
> + */
> +struct smm_variable_getnext {
> + efi_guid_t guid;
> + size_t name_size;
> + u16 name[];
> +};
> +
> +#define MM_VARIABLE_GET_NEXT_HEADER_SIZE \
> + (sizeof(struct smm_variable_getnext))
> +
> +/**
> + * struct smm_variable_query_info - Used to communicate with StMM for
> + * QueryVariableInfo.
> + *
> + * @max_variable_storage: max available storage
> + * @remaining_variable_storage: remaining available storage
> + * @max_variable_size: max variable supported size
> + * @attr: attributes to query storage for
> + *
> + * Defined in EDK2 as SMM_VARIABLE_COMMUNICATE_QUERY_VARIABLE_INFO.
> + */
> +struct smm_variable_query_info {
> + u64 max_variable_storage;
> + u64 remaining_variable_storage;
> + u64 max_variable_size;
> + u32 attr;
> +};
> +
> +#define VAR_CHECK_VARIABLE_PROPERTY_REVISION 0x0001
> +#define VAR_CHECK_VARIABLE_PROPERTY_READ_ONLY BIT(0)
> +/**
> + * struct var_check_property - Used to store variable properties in StMM
> + *
> + * @revision: magic revision number for variable property checking
> + * @property: properties mask for the variable used in StMM.
> + * Currently RO flag is supported
> + * @attributes: variable attributes used in StMM checking when properties
> + * for a variable are enabled
> + * @minsize: minimum allowed size for variable payload checked against
> + * smm_variable_access->datasize in StMM
> + * @maxsize: maximum allowed size for variable payload checked against
> + * smm_variable_access->datasize in StMM
> + *
> + * Defined in EDK2 as VAR_CHECK_VARIABLE_PROPERTY.
> + */
> +struct var_check_property {
> + u16 revision;
> + u16 property;
> + u32 attributes;
> + size_t minsize;
> + size_t maxsize;
> +};
> +
> +/**
> + * struct smm_variable_var_check_property - Used to communicate variable
> + * properties with StMM
> + *
> + * @guid: vendor GUID
> + * @name_size: size of EFI name
> + * @property: variable properties struct
> + * @name: variable name
> + *
> + * Defined in EDK2 as SMM_VARIABLE_COMMUNICATE_VAR_CHECK_VARIABLE_PROPERTY.
> + */
> +struct smm_variable_var_check_property {
> + efi_guid_t guid;
> + size_t name_size;
> + struct var_check_property property;
> + u16 name[];
> +};
> +
> +#endif /* _MM_COMMUNICATION_H_ */
> diff --git a/drivers/tee/optee/optee_private.h b/drivers/tee/optee/optee_private.h
> index 04ae58892608..10af910e0dce 100644
> --- a/drivers/tee/optee/optee_private.h
> +++ b/drivers/tee/optee/optee_private.h
> @@ -12,6 +12,7 @@
> #include <linux/tee_drv.h>
> #include <linux/types.h>
> #include "optee_msg.h"
> +#include "optee_private.h"
This is "optee_private.h", no need to include it.
>
> #define DRIVER_NAME "optee"
>
> @@ -19,6 +20,7 @@
>
> /* Some Global Platform error codes used in this driver */
> #define TEEC_SUCCESS 0x00000000
> +#define TEEC_ERROR_EXCESS_DATA 0xFFFF0004
> #define TEEC_ERROR_BAD_PARAMETERS 0xFFFF0006
> #define TEEC_ERROR_NOT_SUPPORTED 0xFFFF000A
> #define TEEC_ERROR_COMMUNICATION 0xFFFF000E
> @@ -250,7 +252,6 @@ void optee_pool_op_free_helper(struct tee_shm_pool *pool, struct tee_shm *shm,
> int (*shm_unregister)(struct tee_context *ctx,
> struct tee_shm *shm));
>
> -
> void optee_remove_common(struct optee *optee);
> int optee_open(struct tee_context *ctx, bool cap_memref_null);
> void optee_release(struct tee_context *ctx);
> @@ -322,4 +323,6 @@ void optee_smc_abi_unregister(void);
> int optee_ffa_abi_register(void);
> void optee_ffa_abi_unregister(void);
>
> +int optee_efivar_ops_init(struct tee_context *ctx);
This isn't used or implemented as far as I can tell.
> +
> #endif /*OPTEE_PRIVATE_H*/
> diff --git a/drivers/tee/optee/optee_stmm_efi.c b/drivers/tee/optee/optee_stmm_efi.c
> new file mode 100644
> index 000000000000..6dcf1eb4b96c
> --- /dev/null
> +++ b/drivers/tee/optee/optee_stmm_efi.c
> @@ -0,0 +1,598 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * EFI variable service via OP-TEE
> + *
> + * Copyright (C) 2022 Linaro
> + */
> +
> +#include <linux/efi.h>
> +#include <linux/kernel.h>
> +#include <linux/slab.h>
> +#include <linux/tee.h>
> +#include <linux/tee_drv.h>
> +#include <linux/ucs2_string.h>
> +#include "mm_communication.h"
> +#include "optee_private.h"
> +
> +static struct efivars optee_efivars;
> +static struct efivar_operations optee_ops;
optee_efi_ops instead? To avoid being confused with the other optee_ops.
> +
> +static size_t max_buffer_size; /* comm + var + func + data */
> +static size_t max_payload_size; /* func + data */
> +
> +struct mm_connection {
> + struct tee_context *ctx;
> + u32 session;
> +};
> +
> +/* UUID of the stmm PTA */
> +static const struct tee_client_device_id optee_stmm_efi_id_table[] = {
> + {PTA_STMM_UUID},
> + {}
> +};
> +
> +static int optee_ctx_match(struct tee_ioctl_version_data *ver, const void *data)
> +{
> + if (ver->impl_id == TEE_IMPL_ID_OPTEE)
> + return 1;
> + else
> + return 0;
> +}
> +
> +/**
> + * get_connection() - Retrieve OP-TEE session for a specific UUID.
> + *
> + * @conn: session buffer to fill
> + * Return: status code
> + */
> +static int get_connection(struct mm_connection *conn)
> +{
> + struct tee_context *ctx = NULL;
> + struct tee_ioctl_open_session_arg arg;
> + int rc;
> +
> + memset(&arg, 0, sizeof(arg));
> +
> + /* Open context with OP-TEE driver */
> + ctx = tee_client_open_context(NULL, optee_ctx_match, NULL, NULL);
tee_client_close_context() is missing in the error paths.
> + if (IS_ERR(ctx))
> + return -ENODEV;
> +
> + export_uuid(arg.uuid, &optee_stmm_efi_id_table[0].uuid);
> + rc = tee_client_open_session(ctx, &arg, NULL);
> + if (!rc) {
> + conn->ctx = ctx;
> + conn->session = arg.session;
> + }
> +
> + return rc;
> +}
> +
> +/**
> + * optee_mm_communicate() - Pass a buffer to StandaloneMM running in OP-TEE
> + *
> + * @comm_buf: locally allocated communcation buffer
> + * @dsize: buffer size
> + * Return: status code
> + */
> +static efi_status_t optee_mm_communicate(void *comm_buf, size_t dsize)
> +{
> + size_t buf_size;
> + efi_status_t ret;
> + struct efi_mm_communicate_header *mm_hdr;
> + struct mm_connection conn = { NULL, 0 };
> + struct tee_ioctl_invoke_arg arg;
> + struct tee_param param[4];
> + struct tee_shm *shm = NULL;
> + int rc;
> +
> + if (!comm_buf)
> + return EFI_INVALID_PARAMETER;
> +
> + mm_hdr = (struct efi_mm_communicate_header *)comm_buf;
No need to cast.
> + buf_size = mm_hdr->message_len + sizeof(efi_guid_t) + sizeof(size_t);
> +
> + if (dsize != buf_size)
> + return EFI_INVALID_PARAMETER;
> +
> + rc = get_connection(&conn);
> + if (rc) {
> + pr_err("Unable to open OP-TEE session (err=%d)\n", rc);
Perhaps better to print from get_connection() to be able to distinguish
between errors from tee_client_open_context() and
tee_client_open_session().
> + return EFI_UNSUPPORTED;
> + }
> +
> + shm = tee_shm_register_kernel_buf(conn.ctx, comm_buf, buf_size);
> + if (IS_ERR(shm)) {
> + pr_err("Unable to register shared memory\n");
> + tee_client_close_session(conn.ctx, conn.session);
> + return EFI_UNSUPPORTED;
> + }
> +
> + memset(&arg, 0, sizeof(arg));
> + arg.func = PTA_STMM_CMDID_COMMUNICATE;
> + arg.session = conn.session;
> + arg.num_params = 4;
> +
> + memset(param, 0, sizeof(param));
> + param[0].attr = TEE_IOCTL_PARAM_ATTR_TYPE_MEMREF_INOUT;
> + param[0].u.memref.size = buf_size;
> + param[0].u.memref.shm = shm;
> + param[1].attr = TEE_IOCTL_PARAM_ATTR_TYPE_VALUE_OUTPUT;
> + param[2].attr = TEE_IOCTL_PARAM_ATTR_TYPE_NONE;
> + param[3].attr = TEE_IOCTL_PARAM_ATTR_TYPE_NONE;
> +
> + rc = tee_client_invoke_func(conn.ctx, &arg, param);
> + tee_shm_free(shm);
> + /* even if close session fails the session will be invalidaded */
> + tee_client_close_session(conn.ctx, conn.session);
> + if (rc)
> + return EFI_DEVICE_ERROR;
> + if (arg.ret == TEEC_ERROR_EXCESS_DATA)
> + pr_err("Variable payload too large\n");
> + if (arg.ret != TEEC_SUCCESS)
> + return EFI_DEVICE_ERROR;
> +
> + switch (param[1].u.value.a) {
> + case ARM_SVC_SPM_RET_SUCCESS:
> + ret = EFI_SUCCESS;
> + break;
> +
> + case ARM_SVC_SPM_RET_INVALID_PARAMS:
> + ret = EFI_INVALID_PARAMETER;
> + break;
> +
> + case ARM_SVC_SPM_RET_DENIED:
> + ret = EFI_ACCESS_DENIED;
> + break;
> +
> + case ARM_SVC_SPM_RET_NO_MEMORY:
> + ret = EFI_OUT_OF_RESOURCES;
> + break;
> +
> + default:
> + ret = EFI_ACCESS_DENIED;
> + }
> +
> + return ret;
> +}
> +
> +/**
> + * mm_communicate() - Adjust the cmonnucation buffer to StandAlonneMM and send
> + * it to OP-TEE
> + *
> + * @comm_buf: locally allocated communcation buffer
> + * @dsize: buffer size
> + * Return: status code
> + */
> +static efi_status_t mm_communicate(u8 *comm_buf, size_t dsize)
> +{
> + efi_status_t ret;
> + struct efi_mm_communicate_header *mm_hdr;
> + struct smm_variable_communicate_header *var_hdr;
> +
> + dsize += MM_COMMUNICATE_HEADER_SIZE + MM_VARIABLE_COMMUNICATE_SIZE;
> + mm_hdr = (struct efi_mm_communicate_header *)comm_buf;
> + var_hdr = (struct smm_variable_communicate_header *)mm_hdr->data;
> +
> + ret = optee_mm_communicate(comm_buf, dsize);
> + if (ret != EFI_SUCCESS) {
> + pr_err("%s failed!\n", __func__);
> + return ret;
> + }
> +
> + return var_hdr->ret_status;
> +}
> +
> +/**
> + * setup_mm_hdr() - Allocate a buffer for StandAloneMM and initialize the
> + * header data.
> + *
> + * @dptr: pointer address of the corresponding StandAloneMM
> + * function
> + * @payload_size: buffer size
> + * @func: standAloneMM function number
> + * @ret: EFI return code
> + * Return: buffer or NULL
> + */
> +static u8 *setup_mm_hdr(void **dptr, size_t payload_size, size_t func,
> + efi_status_t *ret)
> +{
> + const efi_guid_t mm_var_guid = EFI_MM_VARIABLE_GUID;
> + struct efi_mm_communicate_header *mm_hdr;
> + struct smm_variable_communicate_header *var_hdr;
> + u8 *comm_buf;
> +
> + /* In the init function we initialize max_buffer_size with
> + * get_max_payload(). So skip the test if max_buffer_size is initialized
> + * StandAloneMM will perform similar checks and drop the buffer if it's
> + * too long
> + */
> + if (max_buffer_size &&
> + max_buffer_size < (MM_COMMUNICATE_HEADER_SIZE +
> + MM_VARIABLE_COMMUNICATE_SIZE + payload_size)) {
> + *ret = EFI_INVALID_PARAMETER;
> + return NULL;
> + }
> +
> + comm_buf = kzalloc(MM_COMMUNICATE_HEADER_SIZE +
> + MM_VARIABLE_COMMUNICATE_SIZE + payload_size,
> + GFP_KERNEL);
> + if (!comm_buf) {
> + *ret = EFI_OUT_OF_RESOURCES;
> + return NULL;
> + }
> +
> + mm_hdr = (struct efi_mm_communicate_header *)comm_buf;
> + memcpy(&mm_hdr->header_guid, &mm_var_guid, sizeof(mm_hdr->header_guid));
> + mm_hdr->message_len = MM_VARIABLE_COMMUNICATE_SIZE + payload_size;
> +
> + var_hdr = (struct smm_variable_communicate_header *)mm_hdr->data;
> + var_hdr->function = func;
> + if (dptr)
> + *dptr = var_hdr->data;
> + *ret = EFI_SUCCESS;
> +
> + return comm_buf;
> +}
> +
> +/**
> + * get_max_payload() - Get variable payload size from StandAloneMM.
> + *
> + * @size: size of the variable in storage
> + * Return: status code
> + */
> +static efi_status_t get_max_payload(size_t *size)
> +{
> + struct smm_variable_payload_size *var_payload = NULL;
> + size_t payload_size;
> + u8 *comm_buf = NULL;
> + efi_status_t ret;
> +
> + if (!size) {
> + ret = EFI_INVALID_PARAMETER;
> + goto out;
> + }
> +
> + payload_size = sizeof(*var_payload);
> + comm_buf = setup_mm_hdr((void **)&var_payload, payload_size,
> + SMM_VARIABLE_FUNCTION_GET_PAYLOAD_SIZE, &ret);
> + if (!comm_buf)
> + goto out;
> +
> + ret = mm_communicate(comm_buf, payload_size);
> + if (ret != EFI_SUCCESS)
> + goto out;
> +
> + /* Make sure the buffer is big enough for storing variables */
> + if (var_payload->size < MM_VARIABLE_ACCESS_HEADER_SIZE + 0x20) {
> + ret = EFI_DEVICE_ERROR;
> + goto out;
> + }
> + *size = var_payload->size;
> + /*
> + * There seems to be a bug in EDK2 miscalculating the boundaries and
> + * size checks, so deduct 2 more bytes to fulfill this requirement. Fix
> + * it up here to ensure backwards compatibility with older versions
> + * (cf. StandaloneMmPkg/Drivers/StandaloneMmCpu/AArch64/EventHandle.c.
> + * sizeof (EFI_MM_COMMUNICATE_HEADER) instead the size minus the
> + * flexible array member).
> + *
> + * size is guaranteed to be > 2 due to checks on the beginning.
> + */
> + *size -= 2;
> +out:
> + kfree(comm_buf);
> + return ret;
> +}
> +
> +static efi_status_t get_property_int(u16 *name, size_t name_size,
> + const efi_guid_t *vendor,
> + struct var_check_property *var_property)
> +{
> + struct smm_variable_var_check_property *smm_property;
> + size_t payload_size;
> + u8 *comm_buf = NULL;
> + efi_status_t ret;
> +
> + memset(var_property, 0, sizeof(*var_property));
> + payload_size = sizeof(*smm_property) + name_size;
> + if (payload_size > max_payload_size) {
> + ret = EFI_INVALID_PARAMETER;
> + goto out;
> + }
> + comm_buf = setup_mm_hdr(
> + (void **)&smm_property, payload_size,
> + SMM_VARIABLE_FUNCTION_VAR_CHECK_VARIABLE_PROPERTY_GET, &ret);
> + if (!comm_buf)
> + goto out;
> +
> + memcpy(&smm_property->guid, vendor, sizeof(smm_property->guid));
> + smm_property->name_size = name_size;
> + memcpy(smm_property->name, name, name_size);
> +
> + ret = mm_communicate(comm_buf, payload_size);
> + /*
> + * Currently only R/O property is supported in StMM.
> + * Variables that are not set to R/O will not set the property in StMM
> + * and the call will return EFI_NOT_FOUND. We are setting the
> + * properties to 0x0 so checking against that is enough for the
> + * EFI_NOT_FOUND case.
> + */
> + if (ret == EFI_NOT_FOUND)
> + ret = EFI_SUCCESS;
> + if (ret != EFI_SUCCESS)
> + goto out;
> + memcpy(var_property, &smm_property->property, sizeof(*var_property));
> +
> +out:
> + kfree(comm_buf);
> + return ret;
> +}
> +
> +static efi_status_t optee_get_variable(u16 *name, efi_guid_t *vendor,
> + u32 *attributes,
> + unsigned long *data_size, void *data)
> +{
> + struct var_check_property var_property;
> + struct smm_variable_access *var_acc;
> + size_t payload_size;
> + size_t name_size;
> + size_t tmp_dsize;
> + u8 *comm_buf = NULL;
> + efi_status_t ret;
> +
> + if (!name || !vendor || !data_size) {
> + ret = EFI_INVALID_PARAMETER;
> + goto out;
> + }
> +
> + name_size = (ucs2_strnlen(name, EFI_VAR_NAME_LEN) + 1) * sizeof(u16);
> + if (name_size > max_payload_size - MM_VARIABLE_ACCESS_HEADER_SIZE) {
> + ret = EFI_INVALID_PARAMETER;
> + goto out;
> + }
> +
> + /* Trim output buffer size */
> + tmp_dsize = *data_size;
> + if (name_size + tmp_dsize >
> + max_payload_size - MM_VARIABLE_ACCESS_HEADER_SIZE) {
> + tmp_dsize = max_payload_size - MM_VARIABLE_ACCESS_HEADER_SIZE -
> + name_size;
> + }
> +
> + /* Get communication buffer and initialize header */
> + payload_size = MM_VARIABLE_ACCESS_HEADER_SIZE + name_size + tmp_dsize;
> + comm_buf = setup_mm_hdr((void **)&var_acc, payload_size,
> + SMM_VARIABLE_FUNCTION_GET_VARIABLE, &ret);
> + if (!comm_buf)
> + goto out;
> +
> + /* Fill in contents */
> + memcpy(&var_acc->guid, vendor, sizeof(var_acc->guid));
> + var_acc->data_size = tmp_dsize;
> + var_acc->name_size = name_size;
> + var_acc->attr = attributes ? *attributes : 0;
> + memcpy(var_acc->name, name, name_size);
> +
> + /* Communicate */
> + ret = mm_communicate(comm_buf, payload_size);
> + if (ret == EFI_SUCCESS || ret == EFI_BUFFER_TOO_SMALL)
> + /* Update with reported data size for trimmed case */
> + *data_size = var_acc->data_size;
> + if (ret != EFI_SUCCESS)
> + goto out;
> +
> + ret = get_property_int(name, name_size, vendor, &var_property);
> + if (ret != EFI_SUCCESS)
> + goto out;
> +
> + if (attributes)
> + *attributes = var_acc->attr;
> +
> + if (data)
> + memcpy(data, (u8 *)var_acc->name + var_acc->name_size,
> + var_acc->data_size);
> + else
> + ret = EFI_INVALID_PARAMETER;
> +
> +out:
> + kfree(comm_buf);
> + return ret;
> +}
> +
> +static efi_status_t optee_get_next_variable(unsigned long *name_size,
> + efi_char16_t *name,
> + efi_guid_t *guid)
> +{
> + struct smm_variable_getnext *var_getnext;
> + size_t payload_size;
> + size_t out_name_size;
> + size_t in_name_size;
> + u8 *comm_buf = NULL;
> + efi_status_t ret;
> +
> + if (!name_size || !name || !guid) {
> + ret = EFI_INVALID_PARAMETER;
> + goto out;
> + }
> +
> + out_name_size = *name_size;
> + in_name_size = (ucs2_strnlen(name, EFI_VAR_NAME_LEN) + 1) * sizeof(u16);
> +
> + if (out_name_size < in_name_size) {
> + ret = EFI_INVALID_PARAMETER;
> + goto out;
> + }
> +
> + if (in_name_size >
> + max_payload_size - MM_VARIABLE_GET_NEXT_HEADER_SIZE) {
> + ret = EFI_INVALID_PARAMETER;
> + goto out;
> + }
> +
> + /* Trim output buffer size */
> + if (out_name_size > max_payload_size - MM_VARIABLE_GET_NEXT_HEADER_SIZE)
> + out_name_size =
> + max_payload_size - MM_VARIABLE_GET_NEXT_HEADER_SIZE;
> +
> + payload_size = MM_VARIABLE_GET_NEXT_HEADER_SIZE + out_name_size;
> + comm_buf = setup_mm_hdr((void **)&var_getnext, payload_size,
> + SMM_VARIABLE_FUNCTION_GET_NEXT_VARIABLE_NAME,
> + &ret);
> + if (!comm_buf)
> + goto out;
> +
> + /* Fill in contents */
> + memcpy(&var_getnext->guid, guid, sizeof(var_getnext->guid));
> + var_getnext->name_size = out_name_size;
> + memcpy(var_getnext->name, name, in_name_size);
> + memset((u8 *)var_getnext->name + in_name_size, 0x0,
> + out_name_size - in_name_size);
> +
> + /* Communicate */
> + ret = mm_communicate(comm_buf, payload_size);
> + if (ret == EFI_SUCCESS || ret == EFI_BUFFER_TOO_SMALL) {
> + /* Update with reported data size for trimmed case */
> + *name_size = var_getnext->name_size;
> + }
> + if (ret != EFI_SUCCESS)
> + goto out;
> +
> + memcpy(guid, &var_getnext->guid, sizeof(*guid));
> + memcpy(name, var_getnext->name, var_getnext->name_size);
> +
> +out:
> + kfree(comm_buf);
> + return ret;
> +}
> +
> +static efi_status_t optee_set_variable(efi_char16_t *name, efi_guid_t *vendor,
> + u32 attributes, unsigned long data_size,
> + void *data)
> +{
> + efi_status_t ret;
> + struct var_check_property var_property;
> + struct smm_variable_access *var_acc;
> + size_t payload_size;
> + size_t name_size;
> + u8 *comm_buf = NULL;
> +
> + if (!name || name[0] == 0 || !vendor) {
> + ret = EFI_INVALID_PARAMETER;
> + goto out;
> + }
> + if (data_size > 0 && !data) {
> + ret = EFI_INVALID_PARAMETER;
> + goto out;
> + }
> + /* Check payload size */
> + name_size = (ucs2_strnlen(name, EFI_VAR_NAME_LEN) + 1) * sizeof(u16);
> + payload_size = MM_VARIABLE_ACCESS_HEADER_SIZE + name_size + data_size;
> + if (payload_size > max_payload_size) {
> + ret = EFI_INVALID_PARAMETER;
> + goto out;
> + }
> +
> + /*
> + * Allocate the buffer early, before switching to RW (if needed)
> + * so we won't need to account for any failures in reading/setting
> + * the properties, if the allocation fails
> + */
> + comm_buf = setup_mm_hdr((void **)&var_acc, payload_size,
> + SMM_VARIABLE_FUNCTION_SET_VARIABLE, &ret);
> + if (!comm_buf)
> + goto out;
> +
> + /*
> + * The API has the ability to override RO flags. If no RO check was
> + * requested switch the variable to RW for the duration of this call
> + */
> + ret = get_property_int(name, name_size, vendor, &var_property);
> + if (ret != EFI_SUCCESS) {
> + pr_err("Getting variable property failed\n");
> + goto out;
> + }
> +
> + if (var_property.property & VAR_CHECK_VARIABLE_PROPERTY_READ_ONLY) {
> + ret = EFI_WRITE_PROTECTED;
> + goto out;
> + }
> +
> + /* Fill in contents */
> + memcpy(&var_acc->guid, vendor, sizeof(var_acc->guid));
> + var_acc->data_size = data_size;
> + var_acc->name_size = name_size;
> + var_acc->attr = attributes;
> + memcpy(var_acc->name, name, name_size);
> + memcpy((u8 *)var_acc->name + name_size, data, data_size);
> +
> +
> + /* Communicate */
> + ret = mm_communicate(comm_buf, payload_size);
> + pr_info("Set Variable %s %d %lx\n", __FILE__, __LINE__, ret);
> +out:
> + kfree(comm_buf);
> + return ret;
> +}
> +
> +static int optee_stmm_efi_probe(struct device *dev)
> +{
> + efi_status_t ret;
> +
> + ret = get_max_payload(&max_payload_size);
> + if (ret != EFI_SUCCESS)
> + return ret;
> +
> + max_buffer_size = MM_COMMUNICATE_HEADER_SIZE +
> + MM_VARIABLE_COMMUNICATE_SIZE +
> + max_payload_size;
> +
> + optee_ops.get_variable = optee_get_variable;
> + optee_ops.get_next_variable = optee_get_next_variable;
> + optee_ops.set_variable = optee_set_variable;
> + /* TODO: support nonblocking variant */
> + optee_ops.set_variable_nonblocking = NULL;
> + /* set NULL, always return EFI_SUCCESS by efi_query_variable_store() */
> + optee_ops.query_variable_store = NULL;
Why aren't you using static initialization instead?
Thanks,
Jens
> +
> + tee_register_efivar_ops(&optee_efivars, &optee_ops);
> +
> + return 0;
> +}
> +
> +static int optee_stmm_efi_remove(struct device *dev)
> +{
> + tee_unregister_efivar_ops(&optee_efivars);
> +
> + return 0;
> +}
> +
> +MODULE_DEVICE_TABLE(tee, optee_stmm_efi_id_table);
> +
> +static struct tee_client_driver optee_stmm_efi_driver = {
> + .id_table = optee_stmm_efi_id_table,
> + .driver = {
> + .name = "optee-stmm-efi",
> + .bus = &tee_bus_type,
> + .probe = optee_stmm_efi_probe,
> + .remove = optee_stmm_efi_remove,
> + },
> +};
> +
> +static int __init optee_stmm_efi_mod_init(void)
> +{
> + return driver_register(&optee_stmm_efi_driver.driver);
> +}
> +
> +static void __exit optee_stmm_efi_mod_exit(void)
> +{
> + driver_unregister(&optee_stmm_efi_driver.driver);
> +}
> +
> +module_init(optee_stmm_efi_mod_init);
> +module_exit(optee_stmm_efi_mod_exit);
> +
> +MODULE_LICENSE("GPL v2");
> +MODULE_AUTHOR("Ilias Apalodimas <ilias.apalodimas at linaro.org>");
> +MODULE_AUTHOR("Masahisa Kojima <masahisa.kojima at linaro.org>");
> +MODULE_DESCRIPTION("OP-TEE based EFI runtime variable service driver");
> diff --git a/drivers/tee/tee_core.c b/drivers/tee/tee_core.c
> index 98da206cd761..ac46274844a3 100644
> --- a/drivers/tee/tee_core.c
> +++ b/drivers/tee/tee_core.c
> @@ -7,6 +7,7 @@
>
> #include <linux/cdev.h>
> #include <linux/cred.h>
> +#include <linux/efi.h>
> #include <linux/fs.h>
> #include <linux/idr.h>
> #include <linux/module.h>
> @@ -1263,6 +1264,28 @@ static void __exit tee_exit(void)
> tee_class = NULL;
> }
>
> +void tee_register_efivar_ops(struct efivars *tee_efivars,
> + struct efivar_operations *ops)
> +{
> + /*
> + * If the firmware EFI runtime services support SetVariable(),
> + * tee-based EFI variable services are not used.
> + */
> + if (!efivar_supports_writes()) {
> + pr_info("Use tee-based EFI runtime variable services\n");
> + efivars_generic_ops_unregister();
> + efivars_register(tee_efivars, ops);
> + }
> +}
> +EXPORT_SYMBOL_GPL(tee_register_efivar_ops);
> +
> +void tee_unregister_efivar_ops(struct efivars *tee_efivars)
> +{
> + efivars_unregister(tee_efivars);
> + efivars_generic_ops_register();
> +}
> +EXPORT_SYMBOL_GPL(tee_unregister_efivar_ops);
> +
> subsys_initcall(tee_init);
> module_exit(tee_exit);
>
> diff --git a/include/linux/efi.h b/include/linux/efi.h
> index 5e301c00e9b0..14d4aa83ce60 100644
> --- a/include/linux/efi.h
> +++ b/include/linux/efi.h
> @@ -39,6 +39,7 @@
> #define EFI_WRITE_PROTECTED ( 8 | (1UL << (BITS_PER_LONG-1)))
> #define EFI_OUT_OF_RESOURCES ( 9 | (1UL << (BITS_PER_LONG-1)))
> #define EFI_NOT_FOUND (14 | (1UL << (BITS_PER_LONG-1)))
> +#define EFI_ACCESS_DENIED (15 | (1UL << (BITS_PER_LONG-1)))
> #define EFI_TIMEOUT (18 | (1UL << (BITS_PER_LONG-1)))
> #define EFI_ABORTED (21 | (1UL << (BITS_PER_LONG-1)))
> #define EFI_SECURITY_VIOLATION (26 | (1UL << (BITS_PER_LONG-1)))
> diff --git a/include/linux/tee_drv.h b/include/linux/tee_drv.h
> index 17eb1c5205d3..def4ea6212ee 100644
> --- a/include/linux/tee_drv.h
> +++ b/include/linux/tee_drv.h
> @@ -7,6 +7,7 @@
> #define __TEE_DRV_H
>
> #include <linux/device.h>
> +#include <linux/efi.h>
> #include <linux/idr.h>
> #include <linux/kref.h>
> #include <linux/list.h>
> @@ -507,4 +508,26 @@ struct tee_context *teedev_open(struct tee_device *teedev);
> */
> void teedev_close_context(struct tee_context *ctx);
>
> +/**
> + * tee_register_efivar_ops() - register the efivar ops
> + * @tee_efivars: pointer to efivars structure
> + * @ops: pointer to contain the efivar operation
> + *
> + * This function registers the tee-based efivar operation as an
> + * EFI Runtime Service.
> + *
> + */
> +void tee_register_efivar_ops(struct efivars *tee_efivars,
> + struct efivar_operations *ops);
> +
> +/**
> + * tee_unregister_efivar_ops() - unregister the efivar ops
> + * @tee_efivars: pointer to efivars structure
> + *
> + * This function unregisters the tee-based efivar operation
> + * and reverts to the generic operation.
> + *
> + */
> +void tee_unregister_efivar_ops(struct efivars *tee_efivars);
> +
> #endif /*__TEE_DRV_H*/
> --
> 2.30.2
>
More information about the linux-arm-kernel
mailing list