[PATCH 7/9] ARM: dts: imx28-evk: Convert to use label references
Stefan Wahren
stefan.wahren at i2se.com
Wed Feb 1 12:33:36 PST 2023
This Freescale board file still use node name and unit address
to reference parts from the imx28.dtsi . This causes a lot of
redundancy. So use label references in order to make it easier
to maintain.
Signed-off-by: Stefan Wahren <stefan.wahren at i2se.com>
Cc: Anson Huang <Anson.Huang at nxp.com>
---
arch/arm/boot/dts/imx28-evk.dts | 462 ++++++++++++++++----------------
1 file changed, 227 insertions(+), 235 deletions(-)
diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts
index 1053b7c584d8..783abb82b2a8 100644
--- a/arch/arm/boot/dts/imx28-evk.dts
+++ b/arch/arm/boot/dts/imx28-evk.dts
@@ -95,266 +95,258 @@ panel_in: endpoint {
};
};
- apb at 80000000 {
- apbh at 80000000 {
- nand-controller at 8000c000 {
- pinctrl-names = "default";
- pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg
- &gpmi_pins_evk>;
- status = "okay";
- };
+ sound {
+ compatible = "fsl,imx28-evk-sgtl5000",
+ "fsl,mxs-audio-sgtl5000";
+ model = "imx28-evk-sgtl5000";
+ saif-controllers = <&saif0 &saif1>;
+ audio-codec = <&sgtl5000>;
+ };
- ssp0: spi at 80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_8bit_pins_a
- &mmc0_cd_cfg &mmc0_sck_cfg>;
- bus-width = <8>;
- wp-gpios = <&gpio2 12 0>;
- vmmc-supply = <®_vddio_sd0>;
- status = "okay";
- };
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pin_gpio3_5>;
- ssp1: spi at 80012000 {
- compatible = "fsl,imx28-mmc";
- bus-width = <8>;
- wp-gpios = <&gpio0 28 0>;
- };
+ user {
+ label = "Heartbeat";
+ gpios = <&gpio3 5 0>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
- ssp2: spi at 80014000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx28-spi";
- pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>;
- status = "okay";
-
- flash: flash at 0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "sst,sst25vf016b", "jedec,spi-nor";
- spi-max-frequency = <40000000>;
- reg = <0>;
- };
- };
+ backlight_display: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 2 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ };
+};
- pinctrl at 80018000 {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_a>;
-
- hog_pins_a: hog at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP1_CMD__GPIO_2_13
- MX28_PAD_SSP1_DATA3__GPIO_2_15
- MX28_PAD_ENET0_RX_CLK__GPIO_4_13
- MX28_PAD_SSP1_SCK__GPIO_2_12
- MX28_PAD_PWM3__GPIO_3_28
- MX28_PAD_LCD_RESET__GPIO_3_30
- MX28_PAD_AUART2_RX__GPIO_3_8
- MX28_PAD_AUART2_TX__GPIO_3_9
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- led_pin_gpio3_5: led_gpio3_5 at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_AUART1_TX__GPIO_3_5
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- gpmi_pins_evk: gpmi-nand-evk at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_CE1N__GPMI_CE1N
- MX28_PAD_GPMI_RDY1__GPMI_READY1
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_evk: lcdif-evk at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RD_E__LCD_VSYNC
- MX28_PAD_LCD_WR_RWN__LCD_HSYNC
- MX28_PAD_LCD_RS__LCD_DOTCLK
- MX28_PAD_LCD_CS__LCD_ENABLE
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
+&auart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_pins_a>;
+ uart-has-rtscts;
+ status = "okay";
+};
- lcdif at 80030000 {
- pinctrl-names = "default";
- pinctrl-0 = <&lcdif_24bit_pins_a
- &lcdif_pins_evk>;
- status = "okay";
-
- port {
- display_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
- };
+&auart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart3_pins_a>;
+ status = "okay";
+};
- can0: can at 80032000 {
- pinctrl-names = "default";
- pinctrl-0 = <&can0_pins_a>;
- xceiver-supply = <®_can_3v3>;
- status = "okay";
- };
+&can0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&can0_pins_a>;
+ xceiver-supply = <®_can_3v3>;
+ status = "okay";
+};
- can1: can at 80034000 {
- pinctrl-names = "default";
- pinctrl-0 = <&can1_pins_a>;
- xceiver-supply = <®_can_3v3>;
- status = "okay";
- };
- };
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&can1_pins_a>;
+ xceiver-supply = <®_can_3v3>;
+ status = "okay";
+};
- apbx at 80040000 {
- saif0: saif at 80042000 {
- pinctrl-names = "default";
- pinctrl-0 = <&saif0_pins_a>;
- status = "okay";
- };
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+};
- saif1: saif at 80046000 {
- pinctrl-names = "default";
- pinctrl-0 = <&saif1_pins_a>;
- fsl,saif-master = <&saif0>;
- status = "okay";
- };
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg
+ &gpmi_pins_evk>;
+ status = "okay";
+};
- lradc at 80050000 {
- status = "okay";
- fsl,lradc-touchscreen-wires = <4>;
- fsl,ave-ctrl = <4>;
- fsl,ave-delay = <2>;
- fsl,settling = <10>;
- };
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_24bit_pins_a
+ &lcdif_pins_evk>;
+ status = "okay";
- i2c0: i2c at 80058000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-
- sgtl5000: codec at a {
- compatible = "fsl,sgtl5000";
- reg = <0x0a>;
- #sound-dai-cells = <0>;
- VDDA-supply = <®_3p3v>;
- VDDIO-supply = <®_3p3v>;
- clocks = <&saif0>;
- };
-
- at24 at 51 {
- compatible = "atmel,24c32";
- pagesize = <32>;
- reg = <0x51>;
- };
- };
+ port {
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+};
- pwm: pwm at 80064000 {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm2_pins_a>;
- status = "okay";
- };
+&lradc {
+ fsl,lradc-touchscreen-wires = <4>;
+ fsl,ave-ctrl = <4>;
+ fsl,ave-delay = <2>;
+ fsl,settling = <10>;
+ status = "okay";
+};
- duart: serial at 80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_a>;
- status = "okay";
- };
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ sgtl5000: codec at a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ #sound-dai-cells = <0>;
+ VDDA-supply = <®_3p3v>;
+ VDDIO-supply = <®_3p3v>;
+ clocks = <&saif0>;
+ };
- auart0: serial at 8006a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart0_pins_a>;
- uart-has-rtscts;
- status = "okay";
- };
+ at24 at 51 {
+ compatible = "atmel,24c32";
+ pagesize = <32>;
+ reg = <0x51>;
+ };
+};
- auart3: serial at 80070000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart3_pins_a>;
- status = "okay";
- };
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ phy-supply = <®_fec_3v3>;
+ phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <100>;
+ status = "okay";
+};
- usbphy0: usbphy at 8007c000 {
- status = "okay";
- };
+&mac1 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac1_pins_a>;
+ status = "okay";
+};
- usbphy1: usbphy at 8007e000 {
- status = "okay";
- };
- };
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP1_CMD__GPIO_2_13
+ MX28_PAD_SSP1_DATA3__GPIO_2_15
+ MX28_PAD_ENET0_RX_CLK__GPIO_4_13
+ MX28_PAD_SSP1_SCK__GPIO_2_12
+ MX28_PAD_PWM3__GPIO_3_28
+ MX28_PAD_LCD_RESET__GPIO_3_30
+ MX28_PAD_AUART2_RX__GPIO_3_8
+ MX28_PAD_AUART2_TX__GPIO_3_9
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
- ahb at 80080000 {
- usb0: usb at 80080000 {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_pins_a>;
- vbus-supply = <®_usb0_vbus>;
- status = "okay";
- };
-
- usb1: usb at 80090000 {
- vbus-supply = <®_usb1_vbus>;
- status = "okay";
- };
-
- mac0: ethernet at 800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
- phy-supply = <®_fec_3v3>;
- phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <100>;
- status = "okay";
- };
+ led_pin_gpio3_5: led_gpio3_5 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART1_TX__GPIO_3_5
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
- mac1: ethernet at 800f4000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac1_pins_a>;
- status = "okay";
- };
+ gpmi_pins_evk: gpmi-nand-evk at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_CE1N__GPMI_CE1N
+ MX28_PAD_GPMI_RDY1__GPMI_READY1
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
- sound {
- compatible = "fsl,imx28-evk-sgtl5000",
- "fsl,mxs-audio-sgtl5000";
- model = "imx28-evk-sgtl5000";
- saif-controllers = <&saif0 &saif1>;
- audio-codec = <&sgtl5000>;
+ lcdif_pins_evk: lcdif-evk at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
+};
- leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pin_gpio3_5>;
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm2_pins_a>;
+ status = "okay";
+};
- user {
- label = "Heartbeat";
- gpios = <&gpio3 5 0>;
- linux,default-trigger = "heartbeat";
- };
- };
+&saif0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif0_pins_a>;
+ status = "okay";
+};
- backlight_display: backlight {
- compatible = "pwm-backlight";
- pwms = <&pwm 2 5000000>;
- brightness-levels = <0 4 8 16 32 64 128 255>;
- default-brightness-level = <6>;
+&saif1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif1_pins_a>;
+ fsl,saif-master = <&saif0>;
+ status = "okay";
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <8>;
+ wp-gpios = <&gpio2 12 0>;
+ vmmc-supply = <®_vddio_sd0>;
+ status = "okay";
+};
+
+&ssp1 {
+ compatible = "fsl,imx28-mmc";
+ bus-width = <8>;
+ wp-gpios = <&gpio0 28 0>;
+};
+
+&ssp2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+
+ flash: flash at 0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "sst,sst25vf016b", "jedec,spi-nor";
+ spi-max-frequency = <40000000>;
};
};
+
+&usb0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_pins_a>;
+ vbus-supply = <®_usb0_vbus>;
+ status = "okay";
+};
+
+&usb1 {
+ vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
+
+&usbphy0 {
+ status = "okay";
+};
+
+&usbphy1 {
+ status = "okay";
+};
--
2.34.1
More information about the linux-arm-kernel
mailing list