[PATCH 1/9] ARM: dts: imx28-apf28: Convert to use label references
Stefan Wahren
stefan.wahren at i2se.com
Wed Feb 1 12:33:30 PST 2023
These Armadeus board files still use node name and unit address
to reference parts from the imx28.dtsi . This causes a lot of
redundancy. So use label references in order to make it easier
to maintain.
Signed-off-by: Stefan Wahren <stefan.wahren at i2se.com>
Cc: <support at armadeus.com>
---
arch/arm/boot/dts/imx28-apf28.dts | 96 ++++-----
arch/arm/boot/dts/imx28-apf28dev.dts | 312 +++++++++++++--------------
2 files changed, 196 insertions(+), 212 deletions(-)
diff --git a/arch/arm/boot/dts/imx28-apf28.dts b/arch/arm/boot/dts/imx28-apf28.dts
index 14a92fe59770..98672932e41b 100644
--- a/arch/arm/boot/dts/imx28-apf28.dts
+++ b/arch/arm/boot/dts/imx28-apf28.dts
@@ -14,67 +14,59 @@ memory at 40000000 {
device_type = "memory";
reg = <0x40000000 0x08000000>;
};
+};
- apb at 80000000 {
- apbh at 80000000 {
- nand-controller at 8000c000 {
- pinctrl-names = "default";
- pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
- status = "okay";
-
- partition at 0 {
- label = "u-boot";
- reg = <0x0 0x300000>;
- };
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+};
- partition at 300000 {
- label = "env";
- reg = <0x300000 0x80000>;
- };
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+ status = "okay";
- partition at 380000 {
- label = "env2";
- reg = <0x380000 0x80000>;
- };
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x300000>;
+ };
- partition at 400000 {
- label = "dtb";
- reg = <0x400000 0x80000>;
- };
+ partition at 300000 {
+ label = "env";
+ reg = <0x300000 0x80000>;
+ };
- partition at 480000 {
- label = "splash";
- reg = <0x480000 0x80000>;
- };
+ partition at 380000 {
+ label = "env2";
+ reg = <0x380000 0x80000>;
+ };
- partition at 500000 {
- label = "kernel";
- reg = <0x500000 0x800000>;
- };
+ partition at 400000 {
+ label = "dtb";
+ reg = <0x400000 0x80000>;
+ };
- partition at d00000 {
- label = "rootfs";
- reg = <0xd00000 0xf300000>;
- };
- };
- };
+ partition at 480000 {
+ label = "splash";
+ reg = <0x480000 0x80000>;
+ };
- apbx at 80040000 {
- duart: serial at 80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_a>;
- status = "okay";
- };
- };
+ partition at 500000 {
+ label = "kernel";
+ reg = <0x500000 0x800000>;
};
- ahb at 80080000 {
- mac0: ethernet at 800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
- phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
- status = "okay";
- };
+ partition at d00000 {
+ label = "rootfs";
+ reg = <0xd00000 0xf300000>;
};
};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-apf28dev.dts b/arch/arm/boot/dts/imx28-apf28dev.dts
index 1b253b47006c..47e2397193ad 100644
--- a/arch/arm/boot/dts/imx28-apf28dev.dts
+++ b/arch/arm/boot/dts/imx28-apf28dev.dts
@@ -10,166 +10,6 @@ / {
model = "Armadeus Systems APF28Dev docking/development board";
compatible = "armadeus,imx28-apf28dev", "armadeus,imx28-apf28", "fsl,imx28";
- apb at 80000000 {
- apbh at 80000000 {
- ssp0: spi at 80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_4bit_pins_a
- &mmc0_cd_cfg &mmc0_sck_cfg>;
- bus-width = <4>;
- status = "okay";
- };
-
- ssp2: spi at 80014000 {
- compatible = "fsl,imx28-spi";
- pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>;
- status = "okay";
- };
-
- pinctrl at 80018000 {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_apf28dev>;
-
- hog_pins_apf28dev: hog at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D16__GPIO_1_16
- MX28_PAD_LCD_D17__GPIO_1_17
- MX28_PAD_LCD_D18__GPIO_1_18
- MX28_PAD_LCD_D19__GPIO_1_19
- MX28_PAD_LCD_D20__GPIO_1_20
- MX28_PAD_LCD_D21__GPIO_1_21
- MX28_PAD_LCD_D22__GPIO_1_22
- MX28_PAD_GPMI_CE1N__GPIO_0_17
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_apf28dev: lcdif-apf28dev at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RD_E__LCD_VSYNC
- MX28_PAD_LCD_WR_RWN__LCD_HSYNC
- MX28_PAD_LCD_RS__LCD_DOTCLK
- MX28_PAD_LCD_CS__LCD_ENABLE
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- usb0_otg_apf28dev: otg-apf28dev at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D23__GPIO_1_23
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
-
- lcdif at 80030000 {
- pinctrl-names = "default";
- pinctrl-0 = <&lcdif_16bit_pins_a
- &lcdif_pins_apf28dev>;
- display = <&display0>;
- status = "okay";
-
- display0: display0 {
- bits-per-pixel = <16>;
- bus-width = <16>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <33000033>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <96>;
- hfront-porch = <96>;
- vback-porch = <20>;
- vfront-porch = <21>;
- hsync-len = <64>;
- vsync-len = <4>;
- hsync-active = <1>;
- vsync-active = <1>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
- };
- };
- };
-
- can0: can at 80032000 {
- pinctrl-names = "default";
- pinctrl-0 = <&can0_pins_a>;
- xceiver-supply = <®_can0_vcc>;
- status = "okay";
- };
- };
-
- apbx at 80040000 {
- lradc at 80050000 {
- fsl,lradc-touchscreen-wires = <4>;
- status = "okay";
- };
-
- i2c0: i2c at 80058000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
- };
-
- pwm: pwm at 80064000 {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm3_pins_a &pwm4_pins_a>;
- status = "okay";
- };
-
- auart0: serial at 8006a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart0_pins_a>;
- uart-has-rtscts;
- status = "okay";
- };
-
- usbphy0: usbphy at 8007c000 {
- status = "okay";
- };
-
- usbphy1: usbphy at 8007e000 {
- status = "okay";
- };
- };
- };
-
- ahb at 80080000 {
- usb0: usb at 80080000 {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_otg_apf28dev
- &usb0_id_pins_b>;
- vbus-supply = <®_usb0_vbus>;
- status = "okay";
- };
-
- usb1: usb at 80090000 {
- status = "okay";
- };
-
- mac1: ethernet at 800f4000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac1_pins_a>;
- phy-reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
- status = "okay";
- };
- };
-
regulators {
compatible = "simple-bus";
#address-cells = <1>;
@@ -223,3 +63,155 @@ user-button {
};
};
};
+
+&auart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_pins_a>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&can0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&can0_pins_a>;
+ xceiver-supply = <®_can0_vcc>;
+ status = "okay";
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_16bit_pins_a
+ &lcdif_pins_apf28dev>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ bits-per-pixel = <16>;
+ bus-width = <16>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <33000033>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <96>;
+ hfront-porch = <96>;
+ vback-porch = <20>;
+ vfront-porch = <21>;
+ hsync-len = <64>;
+ vsync-len = <4>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&lradc {
+ fsl,lradc-touchscreen-wires = <4>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+};
+
+&mac1 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac1_pins_a>;
+ phy-reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_apf28dev>;
+
+ hog_pins_apf28dev: hog at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D16__GPIO_1_16
+ MX28_PAD_LCD_D17__GPIO_1_17
+ MX28_PAD_LCD_D18__GPIO_1_18
+ MX28_PAD_LCD_D19__GPIO_1_19
+ MX28_PAD_LCD_D20__GPIO_1_20
+ MX28_PAD_LCD_D21__GPIO_1_21
+ MX28_PAD_LCD_D22__GPIO_1_22
+ MX28_PAD_GPMI_CE1N__GPIO_0_17
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_apf28dev: lcdif-apf28dev at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ usb0_otg_apf28dev: otg-apf28dev at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D23__GPIO_1_23
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm3_pins_a &pwm4_pins_a>;
+ status = "okay";
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_4bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&ssp2 {
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+};
+
+&usb0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_otg_apf28dev
+ &usb0_id_pins_b>;
+ vbus-supply = <®_usb0_vbus>;
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
+
+&usbphy0 {
+ status = "okay";
+};
+
+&usbphy1 {
+ status = "okay";
+};
--
2.34.1
More information about the linux-arm-kernel
mailing list