PHY issue with SJA1105Q/DP84849I Design
Jagan Teki
jagan at amarulasolutions.com
Tue Dec 19 23:19:30 PST 2023
Hi,
We have encountered the PHY issue on 6.1 LTS with SJA1105Q Switch
connected to DP84849I PHY. DP84849I PHY supports dual ethernet ports
so we configure the DT to connect two ports from the switch to PHY and
one port to CPU (FEC in i.MX6DL).
&ecspi2 {
cs-gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi2>;
status = "okay";
switch at 0 {
compatible = "nxp,sja1105q";
reg = <0>;
spi-max-frequency = <4000000>;
spi-rx-delay-us = <1>;
spi-tx-delay-us = <1>;
spi-cpha;
clocks = <&clk25m>;
pinctrl-0 = <&pinctrl_sja1105_rst>;
pinctrl-names = "default";
reset-gpios = <&gpio6 5 GPIO_ACTIVE_LOW>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port at 0 {
reg = <0>;
label = "ethphy0";
phy-handle = <ðphy0>;
phy-mode = "mii";
};
port at 1 {
reg = <1>;
label = "ethphy1";
phy-handle = <ðphy1>;
phy-mode = "mii";
};
port at 2 {
reg = <2>;
status = "disabled";
};
port at 3 {
reg = <3>;
status = "disabled";
};
port at 4 {
reg = <4>;
label = "cpu";
ethernet = <&fec>;
phy-mode = "mii";
rx-internal-delay-ps = <2000>;
tx-internal-delay-ps = <2000>;
fixed-link {
speed = <100>;
full-duplex;
};
};
};
};
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "mii";
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
ethphy0: ethernet-phy at 0 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <0>;
};
ethphy1: ethernet-phy at 1 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <1>;
};
};
};
Since DP84849I shares the same register spec as DP83848, I have used
the DP83848 driver with the below PHY_ID change
diff --git a/drivers/net/phy/dp83848.c b/drivers/net/phy/dp83848.c
index c38d33fd3706..c2c82ce5bb41 100644
--- a/drivers/net/phy/dp83848.c
+++ b/drivers/net/phy/dp83848.c
@@ -8,6 +8,7 @@
#include <linux/module.h>
#include <linux/phy.h>
+#define TI_DP83849I_PHY_ID 0x20005ca2
#define TI_DP83848C_PHY_ID 0x20005ca0
#define TI_DP83620_PHY_ID 0x20005ce0
#define NS_DP83848C_PHY_ID 0x20005c90
@@ -173,6 +174,8 @@ MODULE_DEVICE_TABLE(mdio, dp83848_tbl);
}
static struct phy_driver dp83848_driver[] = {
+ DP83848_PHY_DRIVER(TI_DP83849I_PHY_ID, "TI DP83849I 10/100 Mbps PHY",
+ NULL),
DP83848_PHY_DRIVER(TI_DP83848C_PHY_ID, "TI DP83848C 10/100 Mbps PHY",
NULL),
DP83848_PHY_DRIVER(NS_DP83848C_PHY_ID, "NS DP83848C 10/100 Mbps PHY",
The Switch and dual-phy seem detecting as expected but when we try to
bring up the link the PHY0 says NOLINK as mentioned, below.
root at limx6solo:~# dmesg | grep sja
[ 23.765086] sja1105 spi1.0: spi_imx_setup: mode 1, 8 bpw, 4000000 hz
[ 23.765164] sja1105 spi1.0: setup mode 1, 8 bits/w, 4000000 Hz max --> 0
[ 23.766160] sja1105 spi1.0: Probed switch chip: SJA1105Q
[ 24.037103] sja1105 spi1.0: configuring for fixed/mii link mode
[ 24.119891] sja1105 spi1.0 ethphy0 (uninitialized): PHY
[2188000.ethernet-1:00] driver [TI DP83849I 10/100 Mbps PHY]
(irq=POLL)
[ 24.279129] sja1105 spi1.0 ethphy1 (uninitialized): PHY
[2188000.ethernet-1:01] driver [TI DP83849I 10/100 Mbps PHY]
(irq=POLL)
[ 26.406998] sja1105 spi1.0: Link is Up - 100Mbps/Full - flow control off
root at imx6solo:~# cat /usr/phy.sh
#!/bin/sh
echo ======= MDIO: PHY0 ========
mdio 2188000.ethernet-1 phy 0 raw 0x0
mdio 2188000.ethernet-1 phy 0 raw 0x1
mdio 2188000.ethernet-1 phy 0 raw 0x2
mdio 2188000.ethernet-1 phy 0 raw 0x3
mdio 2188000.ethernet-1 phy 0 raw 0x4
mdio 2188000.ethernet-1 phy 0 raw 0x5
mdio 2188000.ethernet-1 phy 0 raw 0x6
mdio 2188000.ethernet-1 phy 0 raw 0x7
mdio 2188000.ethernet-1 phy 0 raw 0x10
mdio 2188000.ethernet-1 phy 0 raw 0x19
echo ======= MDIO: PHY1 ========
mdio 2188000.ethernet-1 phy 1 raw 0x0
mdio 2188000.ethernet-1 phy 1 raw 0x1
mdio 2188000.ethernet-1 phy 1 raw 0x2
mdio 2188000.ethernet-1 phy 1 raw 0x3
mdio 2188000.ethernet-1 phy 1 raw 0x4
mdio 2188000.ethernet-1 phy 1 raw 0x5
mdio 2188000.ethernet-1 phy 1 raw 0x6
mdio 2188000.ethernet-1 phy 1 raw 0x7
mdio 2188000.ethernet-1 phy 1 raw 0x10
mdio 2188000.ethernet-1 phy 1 raw 0x19
ip link set dev eth0 down
ip link set dev ethphy0 down
ip link set dev ethphy1 down
ip link set dev ethphy0 address 00:11:22:33:44:55
ip link set dev ethphy1 address 00:11:22:33:44:66
ip addr add dev ethphy0 169.254.178.1/16
ip addr add dev ethphy1 169.253.178.2/16
ip link set dev eth0 up
ip link set dev ethphy0 up
ip link set dev ethphy1 up
echo ########## MDIO: PHY0 ###########
mdio 2188000.ethernet-1 phy 0 raw 0x0
mdio 2188000.ethernet-1 phy 0 raw 0x1
mdio 2188000.ethernet-1 phy 0 raw 0x2
mdio 2188000.ethernet-1 phy 0 raw 0x3
mdio 2188000.ethernet-1 phy 0 raw 0x4
mdio 2188000.ethernet-1 phy 0 raw 0x5
mdio 2188000.ethernet-1 phy 0 raw 0x6
mdio 2188000.ethernet-1 phy 0 raw 0x7
mdio 2188000.ethernet-1 phy 0 raw 0x10
mdio 2188000.ethernet-1 phy 0 raw 0x19
echo ########## MDIO: PHY1 ###########
mdio 2188000.ethernet-1 phy 1 raw 0x0
mdio 2188000.ethernet-1 phy 1 raw 0x1
mdio 2188000.ethernet-1 phy 1 raw 0x2
mdio 2188000.ethernet-1 phy 1 raw 0x3
mdio 2188000.ethernet-1 phy 1 raw 0x4
mdio 2188000.ethernet-1 phy 1 raw 0x5
mdio 2188000.ethernet-1 phy 1 raw 0x6
mdio 2188000.ethernet-1 phy 1 raw 0x7
mdio 2188000.ethernet-1 phy 1 raw 0x10
mdio 2188000.ethernet-1 phy 1 raw 0x19
root at ltts-imx6solo:~# bash /usr/phy.sh
======= MDIO: PHY0 ========
0x0: 0x3900
0x1: 0x7849
0x2: 0x2000
0x3: 0x5ca2
0x4: 0x01e1
0x5: 0x45e1
0x6: 0x0006
0x7: 0x2001
0x10: 0x0000
0x19: 0x8020
======= MDIO: PHY1 ========
0x0: 0x3100
0x1: 0x786d
0x2: 0x2000
0x3: 0x5ca2
0x4: 0x01e1
0x5: 0x45e1
0x6: 0x0007
0x7: 0x2801
0x10: 0x0015
0x19: 0x8021
ip link set dev eth0 down
ip link set dev ethphy0 down
ip link set dev ethphy1 down
ip link set dev ethphy0 address 00:11:22:33:44:55
ip link set dev ethphy1 address 00:11:22:33:44:66
ip link set dev eth0 up
ip link set dev ethphy0 up
ip link set dev ethphy1 up
[ 1254.929229] TI DP83849I 10/100 Mbps PHY 2188000.ethernet-1:00:
attached PHY driver (mii_bus:phy_addr=2188000.ethernet-1:00, irq=POLL)
[ 1254.993819] sja1105 spi1.0 ethphy0: configuring for phy/mii link mode
[ 1255.005027] ------------[ cut here ]------------
[ 1255.009962] WARNING: CPU: 0 PID: 374 at drivers/net/phy/phy.c:1157
phy_start+0x58/0xb4
[ 1255.018062] called from state NOLINK
[ 1255.021656] Modules linked in: mdio_netlink(O) bnep tag_sja1105
sja1105 pcs_xpcs brcmfmac brcmutil imx_sdma coda_vpu v4l2_jpeg
imx_vdoa evbug
[ 1255.034578] CPU: 0 PID: 374 Comm: ip Tainted: G O 6.1.58 #1
[ 1255.041560] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 1255.048103] unwind_backtrace from show_stack+0x10/0x14
[ 1255.053361] show_stack from dump_stack_lvl+0x58/0x70
[ 1255.058441] dump_stack_lvl from __warn+0x70/0x1a4
[ 1255.063258] __warn from warn_slowpath_fmt+0x1bc/0x270
[ 1255.068416] warn_slowpath_fmt from phy_start+0x58/0xb4
[ 1255.073662] phy_start from dsa_port_enable_rt+0x54/0x9c
[ 1255.079000] dsa_port_enable_rt from dsa_slave_open+0xb8/0x17c
[ 1255.084860] dsa_slave_open from __dev_open+0xec/0x1ac
[ 1255.090024] __dev_open from __dev_change_flags+0x18c/0x224
[ 1255.095613] __dev_change_flags from dev_change_flags+0x14/0x44
[ 1255.101549] dev_change_flags from do_setlink+0x254/0xe4c
[ 1255.106974] do_setlink from rtnl_newlink+0x598/0x80c
[ 1255.112048] rtnl_newlink from rtnetlink_rcv_msg+0x168/0x574
[ 1255.117722] rtnetlink_rcv_msg from netlink_rcv_skb+0xb8/0x11c
[ 1255.123572] netlink_rcv_skb from netlink_unicast+0x1a8/0x2dc
[ 1255.129343] netlink_unicast from netlink_sendmsg+0x1d8/0x450
[ 1255.135117] netlink_sendmsg from ____sys_sendmsg+0x188/0x258
[ 1255.140891] ____sys_sendmsg from ___sys_sendmsg+0x6c/0xa4
[ 1255.146397] ___sys_sendmsg from sys_sendmsg+0x50/0x98
[ 1255.151556] sys_sendmsg from ret_fast_syscall+0x0/0x1c
[ 1255.156801] Exception stack(0xf10c9fa8 to 0xf10c9ff0)
[ 1255.161867] 9fa0: 00000000 00000001 00000003
beef2730 00000000 00000000
[ 1255.170057] 9fc0: 00000000 00000001 b6f9e5a0 00000128 626adc51
00000000 004d1cc0 004d1cc0
[ 1255.178244] 9fe0: 00000128 beef26d0 b6e9f6d3 b6e11ae6
[ 1255.183469] irq event stamp: 3345
[ 1255.186852] hardirqs last enabled at (3355): [<c0195dbc>]
__up_console_sem+0x50/0x60
[ 1255.194715] hardirqs last disabled at (3362): [<c0195da8>]
__up_console_sem+0x3c/0x60
[ 1255.202628] softirqs last enabled at (3344): [<c01017d0>]
__do_softirq+0x2c0/0x57c
[ 1255.210365] softirqs last disabled at (3325): [<c012f204>]
__irq_exit_rcu+0x138/0x17c
[ 1255.218281] ---[ end trace 0000000000000000 ]---
[ 1255.293759] sja1105 spi1.0 ethphy1: configuring for phy/mii link mode
0x3100
0x7849
0x2000
0x5ca2
0x05e1
0x0000
0x0004
0x2001
0x0000
0x8020
0x3100
0x7849
0x2000
0x5ca2
0x0141
0x0000
0x0005
0x2801
0x0000
0x8021
root at ltts-imx6solo:~# [ 1257.045875] fec 2188000.ethernet eth0: Link
is Up - 100Mbps/Full - flow control rx/tx
[ 1257.054008] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1257.365971] sja1105 spi1.0 ethphy1: Link is Up - 100Mbps/Full -
flow control off
[ 1257.373455] IPv6: ADDRCONF(NETDEV_CHANGE): ethphy1: link becomes ready
root at ltts-imx6solo:~# ifconfig -a
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1504
inet6 fe80::7c4c:1aff:fe5e:cbf0 prefixlen 64 scopeid 0x20<link>
ether 7e:4c:1a:5e:cb:f0 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
ethphy0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 169.254.178.1 netmask 255.255.0.0 broadcast 0.0.0.0
ether 00:11:22:33:44:55 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
ethphy1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 169.253.178.2 netmask 255.255.0.0 broadcast 0.0.0.0
inet6 fe80::211:22ff:fe33:4466 prefixlen 64 scopeid 0x20<link>
ether 00:11:22:33:44:66 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 32 bytes 4211 (4.1 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 91 bytes 7801 (7.6 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 91 bytes 7801 (7.6 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
sit0: flags=128<NOARP> mtu 1480
unspec 00-00-00-00-31-00-00-4A-00-00-00-00-00-00-00-00
txqueuelen 1000 (UNSPEC)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether c0:ee:40:82:2f:fc txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
root at ltts-imx6solo:~# mdio 2188000.ethernet-1
DEV PHY-ID LINK
0x00 0x20005ca2 up
0x01 0x20005ca2 up
--
Jagan Teki,
Amarula Solutions India Pvt. Ltd.
Co-Founder & Embedded Linux Architect
405/E-Block, Sri Lakshmi Shubham Arcade, Chandanagar, Hyderabad - 500050, India
M. (+91) 910 009 0959
[`as] http://www.amarulasolutions.com
More information about the linux-arm-kernel
mailing list