[PATCH 10/13] arm64: dts: exynos: gs101: define USI8 with I2C configuration

[Sam Protsenko]

On Thu, Dec 14, 2023 at 4:53 AM Tudor Ambarus <tudor.ambarus at linaro.org> wrote:
>
> USI8 I2C is used to communicate with an eeprom found on the battery
> connector. Define USI8 in I2C configuration.
>
> USI8 CONFIG register comes with a 0x0 reset value, meaning that USI8
> doesn't have a default protocol (I2C, SPI, UART) at reset. Thus the
> selection of the protocol is intentionally left for the board dtsi file.
>
> Signed-off-by: Tudor Ambarus <tudor.ambarus at linaro.org>
> ---
>  arch/arm64/boot/dts/exynos/google/gs101.dtsi | 26 ++++++++++++++++++++
>  1 file changed, 26 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/exynos/google/gs101.dtsi b/arch/arm64/boot/dts/exynos/google/gs101.dtsi
> index ffb7b4d89a8c..4ea1b180cd0a 100644
> --- a/arch/arm64/boot/dts/exynos/google/gs101.dtsi
> +++ b/arch/arm64/boot/dts/exynos/google/gs101.dtsi
> @@ -354,6 +354,32 @@ pinctrl_peric0: pinctrl at 10840000 {
>                         interrupts = <GIC_SPI 625 IRQ_TYPE_LEVEL_HIGH 0>;
>                 };
>
> +               usi8: usi at 109700c0 {
> +                       compatible = "google,gs101-usi",
> +                                    "samsung,exynos850-usi";
> +                       reg = <0x109700c0 0x20>;
> +                       ranges;
> +                       #address-cells = <1>;
> +                       #size-cells = <1>;
> +                       clocks = <&cmu_peric0 CLK_DOUT_PERIC0_USI8_USI>,

Are you sure this is a leaf clock? Usually it's a GATE clock, not a DIV one.

> +                                <&cmu_peric0 CLK_GOUT_PERIC0_CLK_PERIC0_USI8_USI_CLK>;

Because of following letter-for-letter the crazy TRM clock namings,
now it's not possible to keep 80 characters length in a sane way :(

> +                       clock-names = "pclk", "ipclk";
> +                       samsung,sysreg = <&sysreg_peric0 0x101c>;

samsung,mode is not needed in this case?

> +                       status = "disabled";
> +
> +                       hsi2c_8: i2c at 10970000 {
> +                               compatible = "google,gs101-hsi2c",
> +                                            "samsung,exynosautov9-hsi2c";
> +                               reg = <0x10970000 0xc0>;
> +                               interrupts = <GIC_SPI 642
> +                                             IRQ_TYPE_LEVEL_HIGH 0>;

IRQ type constant can fit the previous line.

> +                               clocks = <&cmu_peric0 CLK_DOUT_PERIC0_USI8_USI>,
> +                                        <&cmu_peric0 CLK_GOUT_PERIC0_CLK_PERIC0_USI8_USI_CLK>;
> +                               clock-names = "hsi2c", "hsi2c_pclk";
> +                               status = "disabled";

Pinctrl properties are not needed for this node?

> +                       };
> +               };
> +
>                 usi_uart: usi at 10a000c0 {
>                         compatible = "google,gs101-usi",
>                                      "samsung,exynos850-usi";
> --
> 2.43.0.472.g3155946c3a-goog
>