[PATCH 07/11] drm/rockchip: inno_hdmi: Add basic mode validation

[Maxime Ripard]

Hi,

On Wed, Dec 13, 2023 at 08:51:21PM +0100, Alex Bee wrote:
> As per TRM this controller supports pixelclocks starting from 25 MHz. The
> maximum supported pixelclocks are defined by the phy configurations we
> have. Also it can't support modes that require doubled clocks.
> If there is a phy reference clock we can additionally validate against
> VESA DMT's recommendations.
> Those checks are added to the mode_valid hook of the connector and
> encoder's mode_fixup hook.
> 
> Signed-off-by: Alex Bee <knaerzche at gmail.com>
> ---
>  drivers/gpu/drm/rockchip/inno_hdmi.c | 38 ++++++++++++++++++++++++++--
>  1 file changed, 36 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/gpu/drm/rockchip/inno_hdmi.c b/drivers/gpu/drm/rockchip/inno_hdmi.c
> index f7f0bec725f9..2f839ff31c1c 100644
> --- a/drivers/gpu/drm/rockchip/inno_hdmi.c
> +++ b/drivers/gpu/drm/rockchip/inno_hdmi.c
> @@ -38,6 +38,8 @@ struct inno_hdmi_variant {
>  	struct inno_hdmi_phy_config *default_phy_config;
>  };
>  
> +#define INNO_HDMI_MIN_TMDS_CLOCK  25000000U
> +
>  struct hdmi_data_info {
>  	int vic;
>  	bool sink_has_audio;
> @@ -572,6 +574,34 @@ static int inno_hdmi_setup(struct inno_hdmi *hdmi,
>  	return 0;
>  }
>  
> +static enum drm_mode_status inno_hdmi_mode_valid(struct inno_hdmi *hdmi,
> +						 struct drm_display_mode *mode)
> +{

So, mode_valid is only called to filter out the modes retrieved by
get_modes, but it won't be called when userspace programs a mode. That's
atomic_check's job.

So you probably want to create a shared function between atomic_check
and mode_valid, and call it from both places (or call mode_valid from
atomic_check).

> +	/* No support for double-clock modes */
> +	if (mode->flags & DRM_MODE_FLAG_DBLCLK)
> +		return MODE_BAD;
> +
> +	unsigned int mpixelclk = mode->clock * 1000;

Variables should be declared at the top of the function.

> +	if (mpixelclk < INNO_HDMI_MIN_TMDS_CLOCK)
> +		return MODE_CLOCK_LOW;

You probably want to check the max TMDS clock too?

> +	if (inno_hdmi_find_phy_config(hdmi, mpixelclk) < 0)
> +		return MODE_CLOCK_HIGH;
> +
> +	if (hdmi->refclk) {
> +		long refclk = clk_round_rate(hdmi->refclk, mpixelclk);
> +		unsigned int max_tolerance = mpixelclk / 5000;
> +
> +		/* Vesa DMT standard mentions +/- 0.5% max tolerance */
> +		if (abs(refclk - mpixelclk) > max_tolerance ||
> +		    mpixelclk - refclk > max_tolerance;
> +			return MODE_NOCLOCK;

You should use abs_diff here. abs() will get confused by the unsigned vs
signed comparison.

> +	}
> +
> +	return MODE_OK;
> +}
> +
>  static void inno_hdmi_encoder_mode_set(struct drm_encoder *encoder,
>  				       struct drm_display_mode *mode,
>  				       struct drm_display_mode *adj_mode)
> @@ -602,7 +632,9 @@ static bool inno_hdmi_encoder_mode_fixup(struct drm_encoder *encoder,
>  					 const struct drm_display_mode *mode,
>  					 struct drm_display_mode *adj_mode)
>  {
> -	return true;
> +	struct inno_hdmi *hdmi = encoder_to_inno_hdmi(encoder);
> +
> +	return inno_hdmi_mode_valid(hdmi, adj_mode) == MODE_OK;
>  }

Why do you call mode_valid in mode_fixup?

Maxime
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 228 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20231214/203c756a/attachment.sig>