[PATCH v7 7/7] ARM: dts: sun8i-a83t: Add BananaPi M3 OV8865 camera overlay

[Jernej Škrabec]

Hi Paul,

same comments as for patch 6.

Best regards,
Jernej

On Wednesday, November 22, 2023 3:14:25 PM CET Paul Kocialkowski wrote:
> Add an overlay supporting the OV8865 from the BananaPi Camera v3
> peripheral board. The board has two sensors (OV5640 and OV8865)
> which cannot be supported in parallel as they share the same reset
> pin and the kernel currently has no support for this case.
> 
> Signed-off-by: Paul Kocialkowski <paul.kocialkowski at bootlin.com>
> ---
>  arch/arm/boot/dts/allwinner/Makefile          |   1 +
>  .../sun8i-a83t-bananapi-m3-camera-ov8865.dtso | 109 ++++++++++++++++++
>  2 files changed, 110 insertions(+)
>  create mode 100644 arch/arm/boot/dts/allwinner/sun8i-a83t-bananapi-m3-camera-ov8865.dtso
> 
> diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile
> index a0a9aa6595e4..980ac88634e3 100644
> --- a/arch/arm/boot/dts/allwinner/Makefile
> +++ b/arch/arm/boot/dts/allwinner/Makefile
> @@ -278,6 +278,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
>  	sun8i-a83t-allwinner-h8homlet-v2.dtb \
>  	sun8i-a83t-bananapi-m3.dtb \
>  	sun8i-a83t-bananapi-m3-camera-ov5640.dtbo \
> +	sun8i-a83t-bananapi-m3-camera-ov8865.dtbo \
>  	sun8i-a83t-cubietruck-plus.dtb \
>  	sun8i-a83t-tbs-a711.dtb \
>  	sun8i-h2-plus-bananapi-m2-zero.dtb \
> diff --git a/arch/arm/boot/dts/allwinner/sun8i-a83t-bananapi-m3-camera-ov8865.dtso b/arch/arm/boot/dts/allwinner/sun8i-a83t-bananapi-m3-camera-ov8865.dtso
> new file mode 100644
> index 000000000000..0656ee8d4bfe
> --- /dev/null
> +++ b/arch/arm/boot/dts/allwinner/sun8i-a83t-bananapi-m3-camera-ov8865.dtso
> @@ -0,0 +1,109 @@
> +// SPDX-License-Identifier: GPL-2.0 OR X11
> +/*
> + * Copyright 2022 Bootlin
> + * Author: Kévin L'hôpital <kevin.lhopital at bootlin.com>
> + * Author: Paul Kocialkowski <paul.kocialkowski at bootlin.com>
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +#include <dt-bindings/clock/sun8i-a83t-ccu.h>
> +#include <dt-bindings/gpio/gpio.h>
> +
> +&{/} {
> +	/*
> +	 * These regulators actually have DLDO4 tied to their EN pin, which is
> +	 * described as input supply here for lack of a better representation.
> +	 * Their actual supply is PS, which is always-on.
> +	 */
> +
> +	ov8865_avdd: ov8865-avdd {
> +		compatible = "regulator-fixed";
> +		regulator-name = "ov8865-avdd";
> +		regulator-min-microvolt = <2800000>;
> +		regulator-max-microvolt = <2800000>;
> +		vin-supply = <&reg_dldo4>;
> +	};
> +
> +	ov8865_dovdd: ov8865-dovdd {
> +		compatible = "regulator-fixed";
> +		regulator-name = "ov8865-dovdd";
> +		regulator-min-microvolt = <2800000>;
> +		regulator-max-microvolt = <2800000>;
> +		vin-supply = <&reg_dldo4>;
> +	};
> +
> +	ov8865_dvdd: ov8865-dvdd {
> +		compatible = "regulator-fixed";
> +		regulator-name = "ov8865-dvdd";
> +		regulator-min-microvolt = <1200000>;
> +		regulator-max-microvolt = <1200000>;
> +		vin-supply = <&reg_dldo4>;
> +	};
> +};
> +
> +&ccu {
> +	assigned-clocks = <&ccu CLK_CSI_MCLK>;
> +	assigned-clock-parents = <&osc24M>;
> +	assigned-clock-rates = <24000000>;
> +};
> +
> +&csi {
> +	status = "okay";
> +};
> +
> +&i2c2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c2_pe_pins>;
> +	status = "okay";
> +
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	ov8865: camera at 36 {
> +		compatible = "ovti,ov8865";
> +		reg = <0x36>;
> +
> +		clocks = <&ccu CLK_CSI_MCLK>;
> +		assigned-clocks = <&ccu CLK_CSI_MCLK>;
> +		assigned-clock-parents = <&osc24M>;
> +		assigned-clock-rates = <24000000>;
> +
> +		avdd-supply = <&ov8865_avdd>;
> +		dovdd-supply = <&ov8865_dovdd>;
> +		dvdd-supply = <&ov8865_dvdd>;
> +
> +		powerdown-gpios = <&pio 4 17 GPIO_ACTIVE_LOW>; /* PE17 */
> +		reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */
> +
> +		port {
> +			ov8865_out_mipi_csi2: endpoint {
> +				remote-endpoint = <&mipi_csi2_in_ov8865>;
> +				link-frequencies = /bits/ 64 <360000000>;
> +				data-lanes = <1 2 3 4>;
> +			};
> +		};
> +	};
> +};
> +
> +&mipi_csi2 {
> +	status = "okay";
> +};
> +
> +&mipi_csi2_in {
> +	mipi_csi2_in_ov8865: endpoint {
> +		remote-endpoint = <&ov8865_out_mipi_csi2>;
> +		data-lanes = <1 2 3 4>;
> +	};
> +};
> +
> +&pio {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&csi_mclk_pin>;
> +};
> +
> +&reg_dldo4 {
> +	regulator-min-microvolt = <2800000>;
> +	regulator-max-microvolt = <2800000>;
> +};
>