[PATCH] arm64: dts: ti: k3-am654-icssg2: Enable PHY interrupts for ICSSG2

[Siddharth Vadapalli]

Hello Nishanth,

Thank you for reviewing the patch. I have addressed your feedback in the v2
patch at:
https://lore.kernel.org/r/20231213080216.1710730-1-s-vadapalli@ti.com/

On 04/12/23 18:51, Nishanth Menon wrote:
> On 12:01-20231120, Siddharth Vadapalli wrote:
>> Enable interrupt mode of operation of the DP83867 Ethernet PHY which is
>> used by ICSSG2. The DP83867 PHY driver already supports interrupt handling
>> for interrupts generated by the PHY. Thus, add the necessary device-tree
>> support to enable it.
>>
>> Since the GPIO1_87 line is muxed with EXT_REFCLK1 and SYNC1_OUT, update
>> the pinmux to select GPIO1_87 for routing the interrupt.
>>
>> Signed-off-by: Siddharth Vadapalli <s-vadapalli at ti.com>
>> ---
>>
>> This patch is based on linux-next tagged next-20231120.
>>
>> Regards,
>> Siddharth.
>>
>>  arch/arm64/boot/dts/ti/k3-am654-icssg2.dtso | 17 +++++++++++++++--
>>  1 file changed, 15 insertions(+), 2 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-am654-icssg2.dtso b/arch/arm64/boot/dts/ti/k3-am654-icssg2.dtso
>> index ec8cf20ca3ac..9f723592d0f4 100644
>> --- a/arch/arm64/boot/dts/ti/k3-am654-icssg2.dtso
>> +++ b/arch/arm64/boot/dts/ti/k3-am654-icssg2.dtso
>> @@ -124,21 +124,34 @@ AM65X_IOPAD(0x0088, PIN_INPUT, 2) /* (AG17) PRG2_PRU0_GPO4.PRG2_RGMII1_RX_CTL */
>>  	};
>>  };
>>  
>> +&main_pmx1 {
>> +	/* Select GPIO1_87 for ICSSG2 PHY interrupt */
>> +	icssg2_phy_irq_pins_default: icssg2-phy-irq-default-pins {
>> +		pinctrl-single,pins = <
>> +			AM65X_IOPAD(0x0014, PIN_INPUT, 7) /* (A22) EXT_REFCLK1.GPIO1_87 */
>> +		>;
>> +	};
>> +};
>> +
>>  &icssg2_mdio {
>>  	status = "okay";
>> -	pinctrl-names = "default";
>> -	pinctrl-0 = <&icssg2_mdio_pins_default>;
>> +	pinctrl-names = "default", "icssg2-phy-irq";
>> +	pinctrl-0 = <&icssg2_mdio_pins_default>, <&icssg2_phy_irq_pins_default>;
> 
> why should the pins be part of mdio pinctrl instead of phy?
> 
>>  	#address-cells = <1>;
>>  	#size-cells = <0>;
>>  
>>  	icssg2_phy0: ethernet-phy at 0 {
>>  		reg = <0>;
>> +		interrupt-parent = <&main_gpio1>;
>> +		interrupts = <87 0x2>;
>>  		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
>>  		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
>>  	};
>>  
>>  	icssg2_phy1: ethernet-phy at 3 {
>>  		reg = <3>;
>> +		interrupt-parent = <&main_gpio1>;
>> +		interrupts = <87 0x2>;
> 
> Shouldn't you be using macros for interrupt level like IRQ_TYPE_EDGE_FALLING?
> 
>>  		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
>>  		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
>>  	};
>> -- 
>> 2.34.1
>>
> 

-- 
Regards,
Siddharth.