[PATCH v2 01/14] arm64: dts: imx8mm-kontron: Add support for display bridges on BL i.MX8MM

[Frieder Schrempf]

Hi Shawn,

thanks for reviewing!

On 06.12.23 03:34, Shawn Guo wrote:
> On Thu, Nov 30, 2023 at 05:16:01PM +0100, Frieder Schrempf wrote:
>> From: Frieder Schrempf <frieder.schrempf at kontron.de>
>>
>> The Kontron Electronics BL i.MX8MM has oboard disply bridges for
>> DSI->HDMI and DSI->LVDS conversion. The DSI interface is muxed by
>> a GPIO-controlled switch to one of these two bridges.
>>
>> By default the HDMI bridge is enabled. The LVDS bridge can be
>> selected by loading an additional (panel-specific) overlay.
>>
>> Signed-off-by: Frieder Schrempf <frieder.schrempf at kontron.de>
>> ---
>> Changes for v2:
>> * Rework DSI mux GPIO logic to be compatible with overlay
>> * Switch from 4 to 2 DSI lanes for LVDS bridge to fix non-working display
>> ---
>>  .../boot/dts/freescale/imx8mm-kontron-bl.dts  | 158 ++++++++++++++++++
>>  1 file changed, 158 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
>> index dcec57c20399e..0fb16b811461e 100644
>> --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
>> +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
>> @@ -25,6 +25,17 @@ osc_can: clock-osc-can {
>>  		clock-output-names = "osc-can";
>>  	};
>>  
>> +	hdmi-out {
>> +		compatible = "hdmi-connector";
>> +		type = "a";
>> +
>> +		port {
>> +			hdmi_in_conn: endpoint {
>> +				remote-endpoint = <&bridge_out_conn>;
>> +			};
>> +		};
>> +	};
>> +
>>  	leds {
>>  		compatible = "gpio-leds";
>>  		pinctrl-names = "default";
>> @@ -132,6 +143,102 @@ ethphy: ethernet-phy at 0 {
>>  	};
>>  };
>>  
>> +&gpio4 {
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&pinctrl_gpio4>;
>> +
>> +	dsi_mux_sel_hdmi: dsi-mux-sel-hdmi-hog {
>> +		gpio-hog;
>> +		gpios = <14 GPIO_ACTIVE_HIGH>;
>> +		output-high;
>> +		line-name = "dsi-mux-sel";
>> +		status = "okay";
> 
> Status "okay" is usually used to flip "disabled".

Right, fixed in v3

>> +	};
>> +
>> +	dsi_mux_sel_lvds: dsi-mux-sel-lvds-hog {
>> +		gpio-hog;
>> +		gpios = <14 GPIO_ACTIVE_HIGH>;
>> +		output-low;
>> +		line-name = "dsi-mux-sel";
>> +		status = "disabled";
>> +	};
>> +
>> +	dsi-mux-oe-hog {
>> +		gpio-hog;
>> +		gpios = <15 GPIO_ACTIVE_LOW>;
>> +		output-high;
>> +		line-name = "dsi-mux-oe";
>> +	};
>> +};
>> +
>> +&i2c3 {
>> +	clock-frequency = <400000>;
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&pinctrl_i2c3>;
>> +	status = "okay";
>> +
>> +	hdmi: hdmi at 39 {
>> +		compatible = "adi,adv7535";
>> +		reg = <0x39>;
>> +
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&pinctrl_adv7535>;
>> +
>> +		interrupt-parent = <&gpio4>;
>> +		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
>> +
>> +		adi,dsi-lanes = <4>;
>> +
>> +		a2vdd-supply = <&reg_vdd_1v8>;
>> +		avdd-supply = <&reg_vdd_1v8>;
>> +		dvdd-supply = <&reg_vdd_1v8>;
>> +		pvdd-supply = <&reg_vdd_1v8>;
>> +		v1p2-supply = <&reg_vdd_1v8>;
>> +		v3p3-supply = <&reg_vdd_3v3>;
>> +
>> +		ports {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +
>> +			port at 0 {
>> +				reg = <0>;
> 
> Have a newline between properties and child node.

Fixed in v3

Thanks
Frieder

> 
>> +				bridge_in_dsi_hdmi: endpoint {
>> +					remote-endpoint = <&dsi_out_bridge>;
>> +				};
>> +			};
>> +
>> +			port at 1 {
>> +				reg = <1>;
>> +				bridge_out_conn: endpoint {
>> +					remote-endpoint = <&hdmi_in_conn>;
>> +				};
>> +			};
>> +		};
>> +	};
>> +
>> +	lvds: bridge at 2c {
>> +		compatible = "ti,sn65dsi84";
>> +		reg = <0x2c>;
>> +		enable-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>;
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&pinctrl_sn65dsi84>;
>> +		status = "disabled";
>> +
>> +		ports {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +
>> +			port at 0 {
>> +				reg = <0>;
>> +				bridge_in_dsi_lvds: endpoint {
>> +					remote-endpoint = <&dsi_out_bridge>;
>> +					data-lanes = <1 2>;
>> +				};
>> +			};
>> +		};
>> +	};
>> +};
>> +
>>  &i2c4 {
>>  	clock-frequency = <100000>;
>>  	pinctrl-names = "default";
>> @@ -144,6 +251,30 @@ rx8900: rtc at 32 {
>>  	};
>>  };
>>  
>> +&lcdif {
>> +	status = "okay";
>> +};
>> +
>> +&mipi_dsi {
>> +	samsung,esc-clock-frequency = <54000000>;
>> +	/*
>> +	 * Let the driver calculate an appropriate clock rate based on the pixel
>> +	 * clock instead of using the fixed value from imx8mm.dtsi.
>> +	 */
>> +	/delete-property/ samsung,pll-clock-frequency;
>> +	status = "okay";
>> +
>> +	ports {
>> +		port at 1 {
>> +			reg = <1>;
>> +
>> +			dsi_out_bridge: endpoint {
>> +				remote-endpoint = <&bridge_in_dsi_hdmi>;
>> +			};
>> +		};
>> +	};
>> +};
>> +
>>  &pwm2 {
>>  	pinctrl-names = "default";
>>  	pinctrl-0 = <&pinctrl_pwm2>;
>> @@ -207,6 +338,12 @@ &iomuxc {
>>  	pinctrl-names = "default";
>>  	pinctrl-0 = <&pinctrl_gpio>;
>>  
>> +	pinctrl_adv7535: adv7535grp {
>> +		fsl,pins = <
>> +			MX8MM_IOMUXC_SAI1_TXD4_GPIO4_IO16		0x19
>> +		>;
>> +	};
>> +
>>  	pinctrl_can: cangrp {
>>  		fsl,pins = <
>>  			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28		0x19
>> @@ -277,6 +414,20 @@ MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x19
>>  		>;
>>  	};
>>  
>> +	pinctrl_gpio4: gpio4grp {
>> +		fsl,pins = <
>> +			MX8MM_IOMUXC_SAI1_TXD2_GPIO4_IO14		0x19
>> +			MX8MM_IOMUXC_SAI1_TXD3_GPIO4_IO15		0x19
>> +		>;
>> +	};
>> +
>> +	pinctrl_i2c3: i2c3grp {
>> +		fsl,pins = <
>> +			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL			0x40000083
>> +			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA			0x40000083
>> +		>;
>> +	};
>> +
>>  	pinctrl_i2c4: i2c4grp {
>>  		fsl,pins = <
>>  			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x400001c3
>> @@ -290,6 +441,13 @@ MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT			0x19
>>  		>;
>>  	};
>>  
>> +	pinctrl_sn65dsi84: sn65dsi84grp {
>> +		fsl,pins = <
>> +			MX8MM_IOMUXC_SAI2_TXD0_GPIO4_IO26		0x19
>> +			MX8MM_IOMUXC_SD2_WP_GPIO2_IO20			0x19
>> +		>;
>> +	};
>> +
>>  	pinctrl_uart1: uart1grp {
>>  		fsl,pins = <
>>  			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x140
>> -- 
>> 2.43.0
>>