[PATCH v3 10/14] arm64: dts: imx8mm-kontron: Fix OSM-S devicetrees to match latest hardware
Frieder Schrempf
frieder at fris.de
Wed Dec 6 06:41:13 PST 2023
From: Frieder Schrempf <frieder.schrempf at kontron.de>
The current state of the devicetree for the i.MX8MM OSM-S and the BL
baseboard reflects deprecated prototype hardware. Update the board
description to match the latest hardware revision.
As the old hardware is not available anymore, was only produced in
very small quantities and was broken in some ways, we can safely
fixup the original devicetree.
Fixes: de9618e84f76 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf at kontron.de>
---
Changes for v3:
* none
Changes for v2:
* none
---
.../dts/freescale/imx8mm-kontron-bl-osm-s.dts | 64 ++++++++++++-------
1 file changed, 41 insertions(+), 23 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
index d9fa0deea7002..7c5586efccc59 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
@@ -30,18 +30,18 @@ leds {
led1 {
label = "led1";
- gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
linux,default-trigger = "heartbeat";
};
led2 {
label = "led2";
- gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio3 8 GPIO_ACTIVE_LOW>;
};
led3 {
label = "led3";
- gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio3 7 GPIO_ACTIVE_LOW>;
};
};
@@ -54,7 +54,7 @@ reg_rst_eth2: regulator-rst-eth2 {
compatible = "regulator-fixed";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb_eth2>;
- gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>;
+ gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
enable-active-high;
regulator-always-on;
regulator-name = "rst-usb-eth2";
@@ -91,7 +91,7 @@ can at 0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can>;
clocks = <&osc_can>;
- interrupts-extended = <&gpio4 28 IRQ_TYPE_LEVEL_LOW>;
+ interrupts-extended = <&gpio5 1 IRQ_TYPE_LEVEL_LOW>;
/*
* Limit the SPI clock to 15 MHz to prevent issues
* with corrupted data due to chip errata.
@@ -118,7 +118,7 @@ eeram at 0 {
&fec1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
- phy-connection-type = "rgmii-rxid";
+ phy-connection-type = "rgmii-id";
phy-handle = <ðphy>;
status = "okay";
@@ -127,10 +127,11 @@ mdio {
#size-cells = <0>;
ethphy: ethernet-phy at 0 {
+ compatible = "ethernet-phy-id4f51.e91b",
+ "ethernet-phy-ieee802.3-c22";
reg = <0>;
- reset-assert-us = <1>;
- reset-deassert-us = <15000>;
- reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
};
};
};
@@ -153,11 +154,24 @@ &gpio5 {
"", "", "", "", "", "", "", "";
};
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ usb-hub at 2c {
+ compatible = "microchip,usb2514b";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_hub>;
+ reg = <0x2c>;
+ non-removable-ports = <0>, <3>;
+ reset-gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+ };
+};
+
&i2c4 {
- clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c4>;
- status = "okay";
};
&pwm2 {
@@ -196,13 +210,13 @@ &usbotg2 {
status = "okay";
usb1 at 1 {
- compatible = "usb424,9514";
+ compatible = "usb424,2514";
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
usbnet: ethernet at 1 {
- compatible = "usb424,ec00";
+ compatible = "usbb95,772b";
reg = <1>;
local-mac-address = [ 00 00 00 00 00 00 ];
};
@@ -223,7 +237,7 @@ &usdhc2 {
&iomuxc {
pinctrl_can: cangrp {
fsl,pins = <
- MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x19
+ MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1 0x19
>;
};
@@ -261,27 +275,24 @@ MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
- MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x19 /* PHY RST */
- MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x19 /* ETH IRQ */
+ MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x19 /* PHY RST */
>;
};
pinctrl_gpio_led: gpioledgrp {
fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x19
- MX8MM_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x19
- MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x19
+ MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x19
+ MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19
+ MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x19
>;
};
pinctrl_gpio1: gpio1grp {
fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x19
- MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19
+ MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x19
MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19
MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x19
MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x19
- MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x19
MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x19
>;
};
@@ -292,6 +303,13 @@ MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x19
>;
};
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000083
+ MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000083
+ >;
+ };
+
pinctrl_i2c4: i2c4grp {
fsl,pins = <
MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x40000083
@@ -331,7 +349,7 @@ MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x0
pinctrl_usb_eth2: usbeth2grp {
fsl,pins = <
- MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x19
+ MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x19
>;
};
--
2.43.0
More information about the linux-arm-kernel
mailing list