[PATCH v3 3/4] ARM: dts: am335x-pocketbeagle: enable pru

[Trevor Woerner]

Now that the PRU code is upstream and can be loaded via remoteproc, adjust
the device tree to enable it and adjust the pin muxing so that the default
setting of the pins matches what's is given on the silkscreen and/or
pocketbeagle wiring.

Caveat: In most cases, the silkscreen will indicate, for example, "PRU0.7",
        but it doesn't indicate whether that pin should be enabled for input
        or output. On the PRU a different MODE is used for input versus
        output. So it is unclear which mode to enable (MODE5 = output, MODE6
        = input). In cases where there is a choice (PRU1.11, PRU0.7, PRU0.4,
        PRU0.1, PRU1.10, PRU0.6, PRU0.3, PRU0.2, and PRU0.5) output is assumed
        (MODE5).

        The remaining PRU silkscreen pins do not have a choice and are set as
        follows:
                PRU0.16  MODE5 input
                PRU0.15i MODE6 input

Signed-off-by: Trevor Woerner <twoerner at gmail.com>
---
 .../boot/dts/ti/omap/am335x-pocketbeagle.dts  | 46 +++++++++++++++----
 1 file changed, 36 insertions(+), 10 deletions(-)

diff --git a/arch/arm/boot/dts/ti/omap/am335x-pocketbeagle.dts b/arch/arm/boot/dts/ti/omap/am335x-pocketbeagle.dts
index d4d1770657da..e35d84ca5706 100644
--- a/arch/arm/boot/dts/ti/omap/am335x-pocketbeagle.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-pocketbeagle.dts
@@ -121,7 +121,7 @@ &gpio1 {
 		"P2.24",
 		"P2.33",
 		"P2.22",
-		"P2.18",
+		"P2.18 [PRU0.15i]",
 		"NC",
 		"NC",
 		"P2.01 [PWM1A]",
@@ -271,15 +271,6 @@ AM33XX_PADCONF(AM335X_PIN_GPMC_AD14, PIN_INPUT_PULLUP, MUX_MODE7)
 		pinctrl-single,bias-pulldown   = < 0x10  0x00  0x10  0x18>;
 	};
 
-	/* P2_18 (ZCZ ball U13) gpio1_15 0x83c PIN 15 */
-	P2_18_gpio: P2-18-gpio-pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_GPMC_AD15, PIN_INPUT_PULLUP, MUX_MODE7)
-		>;
-		pinctrl-single,bias-pullup   =   < 0x10  0x10  0x00  0x18>;
-		pinctrl-single,bias-pulldown   = < 0x10  0x00  0x10  0x18>;
-	};
-
 	/* P2_10 (ZCZ ball R14) gpio1_20 0x850 PIN 20 */
 	P2_10_gpio: P2-10-gpio-pins {
 		pinctrl-single,pins = <
@@ -405,6 +396,27 @@ AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLUP, MUX_MODE6)	/* (T17) gpmc
 			AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_OUTPUT_PULLDOWN, MUX_MODE6)	/* (U17) gpmc_wpn.uart4_txd */
 		>;
 	};
+
+	pru0_pins: pinmux-pru0-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR1, PIN_INPUT_PULLUP, MUX_MODE5)/* (D14) xdma_event_intr1.pr1_pru0_pru_r31_16 */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_OUTPUT_PULLDOWN, MUX_MODE5)/* (A14) mcasp0_ahclkx.pr1_pru0_pru_r30_7 */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKR, PIN_OUTPUT_PULLDOWN, MUX_MODE5)	/* (B12) mcasp0_acklr.pr1_pru0_pru_r30_4 */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_OUTPUT_PULLDOWN, MUX_MODE5)	/* (B13) mcasp0_fsx.pr1_pru0_pru_r30_1 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD15, PIN_INPUT_PULLUP, MUX_MODE6)	/* (U13) gpmc_ad15.pr1_pru0_pru_r31_15 */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AXR1, PIN_OUTPUT_PULLDOWN, MUX_MODE5)	/* (D13) mcasp0_axr1.pr1_pru0_pru_r30_6 */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKR, PIN_OUTPUT_PULLDOWN, MUX_MODE5)/* (C12) mcasp0_ahclkr.pr1_pru0_pru_r30_3 */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AXR0, PIN_OUTPUT_PULLDOWN, MUX_MODE5)	/* (D12) mcasp0_axr0.pr1_pru0_pru_r30_2 */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_FSR, PIN_OUTPUT_PULLDOWN, MUX_MODE5)	/* (C13) mcasp0_fsr.pr1_pru0_pru_r30_5 */
+		>;
+	};
+
+	pru1_pins: pinmux-pru1-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_LCD_AC_BIAS_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE5)/*(R6) lcd_ac_bias_en.pr1_pru1_pru_r30_11 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_OUTPUT_PULLDOWN, MUX_MODE5)	/* (V5) lcd_pclk.pr1_pru1_pru_r30_10 */
+		>;
+	};
 };
 
 &epwmss0 {
@@ -486,3 +498,17 @@ &usb0 {
 &usb1 {
 	dr_mode = "host";
 };
+
+&pruss_tm {
+	status = "okay";
+};
+
+&pru0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pru0_pins>;
+};
+
+&pru1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pru1_pins>;
+};
-- 
2.41.0.327.gaa9166bcc0ba