[PATCH 3/3] arm64: dts: rockchip: Add Orange Pi 5
Ondřej Jirman
megi at xff.cz
Tue Aug 15 09:39:53 PDT 2023
Hello Muhammed,
Looks like you trusted Xunlong's DT a bit too much. See a few issues
below.
On Tue, Aug 15, 2023 at 03:59:01PM +0300, Muhammed Efe Cetin wrote:
> ing-List: linux-kernel at vger.kernel.org
>
> Add initial support for OPi5 that includes support for USB2, PCIe2, Sata,
> Sdmmc, SPI Flash, PMIC.
>
> Signed-off-by: Muhammed Efe Cetin <efectn at 6tel.net>
> ---
> .../boot/dts/rockchip/rk3588s-orangepi-5.dts | 873 ++++++++++++++++++
> 1 file changed, 873 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts
> new file mode 100644
> index 000000000000..85071084a207
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts
> @@ -0,0 +1,873 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include "rk3588s.dtsi"
> +
> +/ {
> + model = "Xunlong Orange Pi 5";
> + compatible = "xunlong,orangepi-5", "rockchip,rk3588s";
> +
> + aliases {
> + mmc0 = &sdmmc;
> +
> + serial2 = &uart2;
> + };
> +
> + chosen {
> + stdout-path = "serial2:1500000n8";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 =<&leds_gpio>;
> +
> + led at 1 {
> + gpios = <&gpio1 RK_PA2 GPIO_ACTIVE_HIGH>;
> + label = "status_led";
> + linux,default-trigger = "heartbeat";
> + linux,default-trigger-delay-ms = <0>;
This is a PWM LED hooked to PWM0_M2. You can use a PWM LED drvier.
> + };
> + };
> +
> + adc-keys {
> + compatible = "adc-keys";
> + io-channels = <&saradc 1>;
> + io-channel-names = "buttons";
> + keyup-threshold-microvolt = <1800000>;
> + poll-interval = <100>;
> +
> + vol-up-key {
> + label = "volume up";
> + linux,code = <KEY_VOLUMEUP>;
> + press-threshold-microvolt = <17000>;
> + };
> +
> + vol-down-key {
> + label = "volume down";
> + linux,code = <KEY_VOLUMEDOWN>;
> + press-threshold-microvolt = <417000>;
> + };
> +
> + menu-key {
> + label = "menu";
> + linux,code = <KEY_MENU>;
> + press-threshold-microvolt = <890000>;
> + };
> +
> + back-key {
> + label = "back";
> + linux,code = <KEY_BACK>;
> + press-threshold-microvolt = <1235000>;
None of these 4 buttons are in the scehmatic. There's one recovery button hooked
to saradc 0, instead.
> + };
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + brightness-levels = < 0 20 20 21 21 22 22 23
> + 23 24 24 25 25 26 26 27
> + 27 28 28 29 29 30 30 31
> + 31 32 32 33 33 34 34 35
> + 35 36 36 37 37 38 38 39
> + 40 41 42 43 44 45 46 47
> + 48 49 50 51 52 53 54 55
> + 56 57 58 59 60 61 62 63
> + 64 65 66 67 68 69 70 71
> + 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87
> + 88 89 90 91 92 93 94 95
> + 96 97 98 99 100 101 102 103
> + 104 105 106 107 108 109 110 111
> + 112 113 114 115 116 117 118 119
> + 120 121 122 123 124 125 126 127
> + 128 129 130 131 132 133 134 135
> + 136 137 138 139 140 141 142 143
> + 144 145 146 147 148 149 150 151
> + 152 153 154 155 156 157 158 159
> + 160 161 162 163 164 165 166 167
> + 168 169 170 171 172 173 174 175
> + 176 177 178 179 180 181 182 183
> + 184 185 186 187 188 189 190 191
> + 192 193 194 195 196 197 198 199
> + 200 201 202 203 204 205 206 207
> + 208 209 210 211 212 213 214 215
> + 216 217 218 219 220 221 222 223
> + 224 225 226 227 228 229 230 231
> + 232 233 234 235 236 237 238 239
> + 240 241 242 243 244 245 246 247
> + 248 249 250 251 252 253 254 255>;
Linar table will not give you "linear" looking brightness steps. Use some
algorithm to generate a proper curve of PWM duty cycle -> brightness table.
Either way, the board has no backlight. This should be in overlay if someone
wants to connect some particular display to the board.
> + default-brightness-level = <200>;
> + pwms = <&pwm2 0 25000 0>;
> + };
> +
> + backlight_1: backlight_1 {
> + compatible = "pwm-backlight";
> + brightness-levels = < 0 20 20 21 21 22 22 23
> + 23 24 24 25 25 26 26 27
> + 27 28 28 29 29 30 30 31
> + 31 32 32 33 33 34 34 35
> + 35 36 36 37 37 38 38 39
> + 40 41 42 43 44 45 46 47
> + 48 49 50 51 52 53 54 55
> + 56 57 58 59 60 61 62 63
> + 64 65 66 67 68 69 70 71
> + 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87
> + 88 89 90 91 92 93 94 95
> + 96 97 98 99 100 101 102 103
> + 104 105 106 107 108 109 110 111
> + 112 113 114 115 116 117 118 119
> + 120 121 122 123 124 125 126 127
> + 128 129 130 131 132 133 134 135
> + 136 137 138 139 140 141 142 143
> + 144 145 146 147 148 149 150 151
> + 152 153 154 155 156 157 158 159
> + 160 161 162 163 164 165 166 167
> + 168 169 170 171 172 173 174 175
> + 176 177 178 179 180 181 182 183
> + 184 185 186 187 188 189 190 191
> + 192 193 194 195 196 197 198 199
> + 200 201 202 203 204 205 206 207
> + 208 209 210 211 212 213 214 215
> + 216 217 218 219 220 221 222 223
> + 224 225 226 227 228 229 230 231
> + 232 233 234 235 236 237 238 239
> + 240 241 242 243 244 245 246 247
> + 248 249 250 251 252 253 254 255>;
> + default-brightness-level = <200>;
> + pwms = <&pwm6 0 25000 0>;
> + };
Ditto.
> + vcc12v_dcin: vcc12v-dcin-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc12v_dcin";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + };
The board has no 12V input. Please avoid low-effort copy pasting from vendor's
device tree. Check everything with the schematic to verify DT is actually
describing the HW correctly, if you really want to start from the vendor's DT
when porting the board to mainline Linux.
> + vcc5v0_sys: vcc5v0-sys-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc5v0_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc12v_dcin>;
> + };
Not supplied from 12V power supply.
> + vcc_1v1_nldo_s3: vcc-1v1-nldo-s3-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_1v1_nldo_s3";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + vin-supply = <&vcc5v0_sys>;
> + };
There's no such regulator on the board.
> + vcc_3v3_sd_s0: vcc-3v3-sd-s0-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_3v3_sd_s0";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpios = <&gpio4 RK_PB5 GPIO_ACTIVE_LOW>;
> + enable-active-low;
> + vin-supply = <&vcc_3v3_s3>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
Fixed regulators don't implement regulator-state-*. Also why are you making
this regulator always on? It will be impossible for mmc subsystem to power
cycle the SD card. (without knowing, which is bad, because after powercycle
it will think that uSD I/O is in 3.3V, while it may still be in 1.8V mode)
> + };
>
> + vcc5v0_usbdcin: vcc5v0-usbdcin-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc5v0_usbdcin";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc12v_dcin>;
> + };
No such regulator on the board.
> + vcc5v0_usb: vcc5v0-usb-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc5v0_usb";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc5v0_usbdcin>;
> + };
No such regulator on the board. Host ports' VBUS is either hardwired
to VCC_5V0 or goes throug a a protection circuit and becomes VCC5V0_USB_HOST.
> + vbus5v0_typec: vbus5v0-typec-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vbus5v0_typec";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + gpio = <&gpio3 RK_PC0 GPIO_ACTIVE_HIGH>;
> + vin-supply = <&vcc5v0_usb>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&typec5v_pwren>;
> + };
No such power rail on the board. This should be VBUS_TYPEC power rail.
Please name regulators/power rails as they are named in the schematic.
Otherwise it's impossible to cross-check DT against schematic.
> + combophy_avdd0v85: combophy-avdd0v85-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "combophy_avdd0v85";
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <850000>;
> + vin-supply = <&vdd_0v85_s0>;
> + };
No such regulator on the board.
> + combophy_avdd1v8: combophy-avdd1v8-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "combophy_avdd1v8";
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&avcc_1v8_s0>;
> + };
Again, no such regulator on the board.
> +
> + vcc3v3_pcie2x1l2: vcc3v3-pcie2x1l2-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v3_pcie2x1l2";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + enable-active-high;
> + regulator-boot-on;
> + regulator-always-on;
> + gpios = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
> + startup-delay-us = <50000>;
Startup delay for always-on regulator is kinda pointless. Also why is this
always on? It should not be.
> + vin-supply = <&vcc5v0_sys>;
> + };
No such regulator on the board. You might have meant VCC3V3_PCIE30,
or not?
> +};
> +
> +&combphy0_ps {
> + status = "okay";
> +};
> +
> +&combphy2_psu {
> + status = "okay";
> +};
> +
> +&cpu_b0 {
> + cpu-supply = <&vdd_cpu_big0_s0>;
> + mem-supply = <&vdd_cpu_big0_mem_s0>;
> +};
> +
> +&cpu_b1 {
> + cpu-supply = <&vdd_cpu_big0_s0>;
> + mem-supply = <&vdd_cpu_big0_mem_s0>;
> +};
> +
> +&cpu_b2 {
> + cpu-supply = <&vdd_cpu_big1_s0>;
> + mem-supply = <&vdd_cpu_big1_mem_s0>;
> +};
> +
> +&cpu_b3 {
> + cpu-supply = <&vdd_cpu_big1_s0>;
> + mem-supply = <&vdd_cpu_big1_mem_s0>;
> +};
> +
> +&cpu_l0 {
> + cpu-supply = <&vdd_cpu_lit_s0>;
> + mem-supply = <&vdd_cpu_lit_mem_s0>;
> +};
> +
> +&cpu_l1 {
> + cpu-supply = <&vdd_cpu_lit_s0>;
> + mem-supply = <&vdd_cpu_lit_mem_s0>;
> +};
> +
> +&cpu_l2 {
> + cpu-supply = <&vdd_cpu_lit_s0>;
> + mem-supply = <&vdd_cpu_lit_mem_s0>;
> +};
> +
> +&cpu_l3 {
> + cpu-supply = <&vdd_cpu_lit_s0>;
> + mem-supply = <&vdd_cpu_lit_mem_s0>;
> +};
> +
> +&gmac1 {
> + clock_in_out = "output";
> + phy-handle = <&rgmii_phy1>;
> + phy-mode = "rgmii-rxid";
> + pinctrl-0 = <&gmac1_miim
> + &gmac1_tx_bus2
> + &gmac1_rx_bus2
> + &gmac1_rgmii_clk
> + &gmac1_rgmii_bus>;
> + pinctrl-names = "default";
> + snps,reset-gpio = <&gpio3 RK_PB2 GPIO_ACTIVE_LOW>;
> + snps,reset-active-low;
> + snps,reset-delays-us = <0 20000 100000>;
> + tx_delay = <0x42>;
> + status = "okay";
> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0m2_xfer>;
> + status = "okay";
> +
> + vdd_cpu_big0_s0: vdd_cpu_big0_mem_s0: regulator at 42 {
> + compatible = "rockchip,rk8602";
> + reg = <0x42>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-name = "vdd_cpu_big0_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <1050000>;
> + regulator-ramp-delay = <2300>;
> + vin-supply = <&vcc5v0_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_cpu_big1_s0: vdd_cpu_big1_mem_s0: regulator at 43 {
> + compatible = "rockchip,rk8603", "rockchip,rk8602";
> + reg = <0x43>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-name = "vdd_cpu_big1_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <1050000>;
> + regulator-ramp-delay = <2300>;
> + vin-supply = <&vcc5v0_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> +
> + vdd_npu_s0: vdd_npu_mem_s0: regulator at 42 {
> + compatible = "rockchip,rk8602";
> + reg = <0x42>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-name = "vdd_npu_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <2300>;
> + vin-supply = <&vcc5v0_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +};
> +
> +&i2c6 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c6m3_xfer>;
> + status = "okay";
> +
> + hym8563: rtc at 51 {
> + compatible = "haoyu,hym8563";
> + reg = <0x51>;
> + #clock-cells = <0>;
> + clock-output-names = "hym8563";
> + pinctrl-names = "default";
> + pinctrl-0 = <&hym8563_int>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
> + wakeup-source;
> + };
> +};
> +
> +&mdio1 {
> + rgmii_phy1: ethernet-phy at 1 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0x1>;
> + };
> +};
> +
> +&pcie2x1l2 {
> + reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
> + vpcie3v3-supply = <&vcc3v3_pcie2x1l2>;
> + rockchip,skip-scan-in-resume;
There's no such property.
> + status = "okay";
> +};
> +
> +&pinctrl {
> + gpio-func {
> + leds_gpio: leds-gpio {
> + rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + hym8563 {
> + hym8563_int: hym8563-int {
> + rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + sata {
> + sata_reset:sata-reset{
> + rockchip,pins = <3 RK_PD1 RK_FUNC_GPIO &pcfg_pull_up>;
Not what you think: https://megous.com/dl/tmp/f135580b68cb5dfe.png
> + };
> + };
> +};
> +
> +&pwm2 {
> + pinctrl-names = "active";
> + pinctrl-0 = <&pwm2m0_pins>;
> + status = "okay";
> +};
> +
> +&pwm6 {
> + pinctrl-names = "active";
> + pinctrl-0 = <&pwm6m0_pins>;
> + status = "okay";
> +};
> +
> +&saradc {
> + vref-supply = <&avcc_1v8_s0>;
> + status = "okay";
> +};
> +
> +&sata0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&sata_reset>;
> + status = "disabled";
> +};
Where do you see a SATA port? http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-5.html
Or a reset signal in the schematic?
> +&sdmmc {
> + max-frequency = <150000000>;
> + no-sdio;
> + no-mmc;
> + bus-width = <4>;
> + cap-mmc-highspeed;
> + cap-sd-highspeed;
> + disable-wp;
> + sd-uhs-sdr104;
> + vmmc-supply = <&vcc_3v3_sd_s0>;
> + vqmmc-supply = <&vccio_sd_s0>;
> + status = "okay";
> +};
> +
> +&sfc {
> + pinctrl-0 = <&fspim0_pins>;
> + pinctrl-names = "default";
> + max-freq = <100000000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +
> + spi_flash: spi-flash at 0 {
> + compatible = "jedec,spi-nor";
> + reg = <0x0>;
> + spi-max-frequency = <100000000>;
> + spi-tx-bus-width = <1>;
> + spi-rx-bus-width = <4>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + loader at 0 {
> + label = "loader";
> + reg = <0x0 0x1000000>;
> + };
> + };
Partitions are not really needed.
> + };
> +};
> +
> +&spi2 {
> + status = "okay";
> + assigned-clocks = <&cru CLK_SPI2>;
> + assigned-clock-rates = <200000000>;
> + num-cs = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
> +
> + pmic at 0 {
> + compatible = "rockchip,rk806";
> + reg = <0x0>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
> + <&rk806_dvs2_null>, <&rk806_dvs3_null>;
> + spi-max-frequency = <1000000>;
> +
> + vcc1-supply = <&vcc5v0_sys>;
> + vcc2-supply = <&vcc5v0_sys>;
> + vcc3-supply = <&vcc5v0_sys>;
> + vcc4-supply = <&vcc5v0_sys>;
> + vcc5-supply = <&vcc5v0_sys>;
> + vcc6-supply = <&vcc5v0_sys>;
> + vcc7-supply = <&vcc5v0_sys>;
> + vcc8-supply = <&vcc5v0_sys>;
> + vcc9-supply = <&vcc5v0_sys>;
> + vcc10-supply = <&vcc5v0_sys>;
> + vcc11-supply = <&vcc_2v0_pldo_s3>;
> + vcc12-supply = <&vcc5v0_sys>;
> + vcc13-supply = <&vcc_1v1_nldo_s3>;
> + vcc14-supply = <&vcc_1v1_nldo_s3>;
> + vcca-supply = <&vcc5v0_sys>;
> +
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + rk806_dvs1_null: dvs1-null-pins {
> + pins = "gpio_pwrctrl2";
> + function = "pin_fun0";
> + };
> +
> + rk806_dvs2_null: dvs2-null-pins {
> + pins = "gpio_pwrctrl2";
> + function = "pin_fun0";
> + };
> +
> + rk806_dvs3_null: dvs3-null-pins {
> + pins = "gpio_pwrctrl3";
> + function = "pin_fun0";
> + };
> +
> + regulators {
> + vdd_gpu_s0: vdd_gpu_mem_s0: dcdc-reg1 {
> + regulator-name = "vdd_gpu_s0";
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> + regulator-enable-ramp-delay = <400>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_cpu_lit_s0: vdd_cpu_lit_mem_s0: dcdc-reg2 {
> + regulator-name = "vdd_cpu_lit_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_log_s0: dcdc-reg3 {
> + regulator-name = "vdd_log_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <675000>;
> + regulator-max-microvolt = <750000>;
> + regulator-ramp-delay = <12500>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <750000>;
> + };
> + };
> +
> + vdd_vdenc_s0: vdd_vdenc_mem_s0: dcdc-reg4 {
> + regulator-name = "vdd_vdenc_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_ddr_s0: dcdc-reg5 {
> + regulator-name = "vdd_ddr_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <675000>;
> + regulator-max-microvolt = <900000>;
> + regulator-ramp-delay = <12500>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <850000>;
> + };
> + };
> +
> + vdd2_ddr_s3: dcdc-reg6 {
> + regulator-name = "vdd2_ddr_s3";
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_2v0_pldo_s3: dcdc-reg7 {
> + regulator-name = "vdd_2v0_pldo_s3";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <2000000>;
> + regulator-max-microvolt = <2000000>;
> + regulator-ramp-delay = <12500>;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <2000000>;
> + };
> + };
> +
> + vcc_3v3_s3: dcdc-reg8 {
> + regulator-name = "vcc_3v3_s3";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vddq_ddr_s0: dcdc-reg9 {
> + regulator-name = "vddq_ddr_s0";
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_1v8_s3: dcdc-reg10 {
> + regulator-name = "vcc_1v8_s3";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + avcc_1v8_s0: pldo-reg1 {
> + regulator-name = "avcc_1v8_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_1v8_s0: pldo-reg2 {
> + regulator-name = "vcc_1v8_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + avdd_1v2_s0: pldo-reg3 {
> + regulator-name = "avdd_1v2_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_3v3_s0: pldo-reg4 {
> + regulator-name = "vcc_3v3_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-ramp-delay = <12500>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vccio_sd_s0: pldo-reg5 {
> + regulator-name = "vccio_sd_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-ramp-delay = <12500>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + pldo6_s3: pldo-reg6 {
> + regulator-name = "pldo6_s3";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vdd_0v75_s3: nldo-reg1 {
> + regulator-name = "vdd_0v75_s3";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <750000>;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <750000>;
> + };
> + };
> +
> + vdd_ddr_pll_s0: nldo-reg2 {
> + regulator-name = "vdd_ddr_pll_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <850000>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <850000>;
> + };
> + };
> +
> + avdd_0v75_s0: nldo-reg3 {
> + regulator-name = "avdd_0v75_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <750000>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_0v85_s0: nldo-reg4 {
> + regulator-name = "vdd_0v85_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <850000>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_0v75_s0: nldo-reg5 {
> + regulator-name = "vdd_0v75_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <750000>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
Have you checked all of the above regulators against the schematic?
> + };
> + };
> +};
> +
> +&tsadc {
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-0 = <&uart2m0_xfer>;
> + status = "okay";
> +};
> +
> +&u2phy0 {
> + status = "okay";
> +};
> +
> +&u2phy0_otg {
> + rockchip,typec-vbus-det;
No such property.
That's all from me, but it's not an exhaustive list of issues. You should
go through the schematic and verify that every single node in DT actually
matches what's in there.
kind regards,
o.
> + status = "okay";
> +};
> +
> +&u2phy2 {
> + status = "okay";
> +};
> +
> +&u2phy2_host {
> + status = "okay";
> +};
> +
> +&u2phy3 {
> + status = "okay";
> +};
> +
> +&u2phy3_host {
> + status = "okay";
> +};
> +
> +&usb_host0_ehci {
> + status = "okay";
> +};
> +
> +&usb_host0_ohci {
> + status = "okay";
> +};
> +
> +&usb_host1_ehci {
> + status = "okay";
> +};
> +
> +&usb_host1_ohci {
> + status = "okay";
> +};
>
> +&wdt {
> + status = "okay";
> +};
> --
> 2.41.0
>
More information about the linux-arm-kernel
mailing list