[PATCH 3/3] arm64: dts: rockchip: Add Orange Pi 5
Krzysztof Kozlowski
krzysztof.kozlowski at linaro.org
Tue Aug 15 06:45:14 PDT 2023
On 15/08/2023 14:59, Muhammed Efe Cetin wrote:
> Add initial support for OPi5 that includes support for USB2, PCIe2, Sata,
> Sdmmc, SPI Flash, PMIC.
>
> Signed-off-by: Muhammed Efe Cetin <efectn at 6tel.net>
> ---
> .../boot/dts/rockchip/rk3588s-orangepi-5.dts | 873 ++++++++++++++++++
Without Makefile this won't be build, so this was not ever tested.
> 1 file changed, 873 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts
> new file mode 100644
> index 000000000000..85071084a207
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts
> @@ -0,0 +1,873 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include "rk3588s.dtsi"
> +
> +/ {
> + model = "Xunlong Orange Pi 5";
> + compatible = "xunlong,orangepi-5", "rockchip,rk3588s";
> +
> + aliases {
> + mmc0 = &sdmmc;
> + serial2 = &uart2;
> + };
> +
> + chosen {
> + stdout-path = "serial2:1500000n8";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 =<&leds_gpio>;
> +
> + led at 1 {
Unit address is not correct here, it is not a bus. This should be
reported as warning, so you did not check for warnings.
It does not look like you tested the DTS against bindings. Please run
`make dtbs_check W=1` (see
Documentation/devicetree/bindings/writing-schema.rst or
https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).
> + gpios = <&gpio1 RK_PA2 GPIO_ACTIVE_HIGH>;
> + label = "status_led";
> + linux,default-trigger = "heartbeat";
> + linux,default-trigger-delay-ms = <0>;
> + };
> + };
> +
> + adc-keys {
> + compatible = "adc-keys";
> + io-channels = <&saradc 1>;
> + io-channel-names = "buttons";
> + keyup-threshold-microvolt = <1800000>;
> + poll-interval = <100>;
> +
> + vol-up-key {
> + label = "volume up";
> + linux,code = <KEY_VOLUMEUP>;
> + press-threshold-microvolt = <17000>;
> + };
> +
> + vol-down-key {
> + label = "volume down";
> + linux,code = <KEY_VOLUMEDOWN>;
> + press-threshold-microvolt = <417000>;
> + };
> +
> + menu-key {
> + label = "menu";
> + linux,code = <KEY_MENU>;
> + press-threshold-microvolt = <890000>;
> + };
> +
> + back-key {
> + label = "back";
> + linux,code = <KEY_BACK>;
> + press-threshold-microvolt = <1235000>;
> + };
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + brightness-levels = < 0 20 20 21 21 22 22 23
> + 23 24 24 25 25 26 26 27
> + 27 28 28 29 29 30 30 31
> + 31 32 32 33 33 34 34 35
> + 35 36 36 37 37 38 38 39
> + 40 41 42 43 44 45 46 47
> + 48 49 50 51 52 53 54 55
> + 56 57 58 59 60 61 62 63
> + 64 65 66 67 68 69 70 71
> + 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87
> + 88 89 90 91 92 93 94 95
> + 96 97 98 99 100 101 102 103
> + 104 105 106 107 108 109 110 111
> + 112 113 114 115 116 117 118 119
> + 120 121 122 123 124 125 126 127
> + 128 129 130 131 132 133 134 135
> + 136 137 138 139 140 141 142 143
> + 144 145 146 147 148 149 150 151
> + 152 153 154 155 156 157 158 159
> + 160 161 162 163 164 165 166 167
> + 168 169 170 171 172 173 174 175
> + 176 177 178 179 180 181 182 183
> + 184 185 186 187 188 189 190 191
> + 192 193 194 195 196 197 198 199
> + 200 201 202 203 204 205 206 207
> + 208 209 210 211 212 213 214 215
> + 216 217 218 219 220 221 222 223
> + 224 225 226 227 228 229 230 231
> + 232 233 234 235 236 237 238 239
> + 240 241 242 243 244 245 246 247
> + 248 249 250 251 252 253 254 255>;
> + default-brightness-level = <200>;
> + pwms = <&pwm2 0 25000 0>;
> + };
> +
> + backlight_1: backlight_1 {
No underscores in node names, use -
> + compatible = "pwm-backlight";
> + brightness-levels = < 0 20 20 21 21 22 22 23
> + 23 24 24 25 25 26 26 27
> + 27 28 28 29 29 30 30 31
...
> +
> +&combphy0_ps {
> + status = "okay";
> +};
> +
> +&combphy2_psu {
> + status = "okay";
> +};
> +
> +&cpu_b0 {
> + cpu-supply = <&vdd_cpu_big0_s0>;
> + mem-supply = <&vdd_cpu_big0_mem_s0>;
> +};
> +
> +&cpu_b1 {
> + cpu-supply = <&vdd_cpu_big0_s0>;
> + mem-supply = <&vdd_cpu_big0_mem_s0>;
> +};
> +
> +&cpu_b2 {
> + cpu-supply = <&vdd_cpu_big1_s0>;
> + mem-supply = <&vdd_cpu_big1_mem_s0>;
> +};
> +
> +&cpu_b3 {
> + cpu-supply = <&vdd_cpu_big1_s0>;
> + mem-supply = <&vdd_cpu_big1_mem_s0>;
> +};
> +
> +&cpu_l0 {
> + cpu-supply = <&vdd_cpu_lit_s0>;
> + mem-supply = <&vdd_cpu_lit_mem_s0>;
> +};
> +
> +&cpu_l1 {
> + cpu-supply = <&vdd_cpu_lit_s0>;
> + mem-supply = <&vdd_cpu_lit_mem_s0>;
> +};
> +
> +&cpu_l2 {
> + cpu-supply = <&vdd_cpu_lit_s0>;
> + mem-supply = <&vdd_cpu_lit_mem_s0>;
> +};
> +
> +&cpu_l3 {
> + cpu-supply = <&vdd_cpu_lit_s0>;
> + mem-supply = <&vdd_cpu_lit_mem_s0>;
> +};
> +
> +&gmac1 {
> + clock_in_out = "output";
> + phy-handle = <&rgmii_phy1>;
> + phy-mode = "rgmii-rxid";
> + pinctrl-0 = <&gmac1_miim
> + &gmac1_tx_bus2
> + &gmac1_rx_bus2
> + &gmac1_rgmii_clk
> + &gmac1_rgmii_bus>;
Messed alignment.
> + pinctrl-names = "default";
> + snps,reset-gpio = <&gpio3 RK_PB2 GPIO_ACTIVE_LOW>;
> + snps,reset-active-low;
> + snps,reset-delays-us = <0 20000 100000>;
> + tx_delay = <0x42>;
> + status = "okay";
> +};
> +
...
> +
> +&sfc {
> + pinctrl-0 = <&fspim0_pins>;
> + pinctrl-names = "default";
> + max-freq = <100000000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +
> + spi_flash: spi-flash at 0 {
> + compatible = "jedec,spi-nor";
> + reg = <0x0>;
> + spi-max-frequency = <100000000>;
> + spi-tx-bus-width = <1>;
> + spi-rx-bus-width = <4>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
okay is by default, was it disabled anywhere?
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + loader at 0 {
> + label = "loader";
> + reg = <0x0 0x1000000>;
> + };
> + };
> + };
> +};
> +
Best regards,
Krzysztof
More information about the linux-arm-kernel
mailing list