[PATCH v1 1/2] PCI: xilinx-nwl: Update ECAM default value and remove unnecessary code.

[Bjorn Helgaas]

Ideally the subject would include useful information about *why*
you're changing the ECAM value.  Drop the period at the end of the
subject.  E.g., something like:

  PCI: xilinx-nwl: Increase ECAM size to accommodate 256 buses

On Mon, Aug 07, 2023 at 04:37:32PM +0530, Thippeswamy Havalige wrote:
> Our controller is expecting ECAM size to be programmed by software.
> By programming "NWL_ECAM_VALUE_DEFAULT  12" controller can access up to
> 16MB ECAM region which is used to detect 16 buses, so by updating
> "NWL_ECAM_VALUE_DEFAULT " to 16 so that controller can access up to 256MB
> ECAM region to detect 256 buses.

Rob needs to ack this because it sounds like this change might make
the driver incompatible with DTs in the field, i.e., the user might be
forced to update the DT at the same time as picking up this driver
change.

> E_ECAM_CONTROL register from bit 16 to 20 uses this value as input
> to calculate ECAM Size.
> 
> The primary,secondary and sub-ordinate bus number registers are updated
> by Linux PCI core, so removing code which is updating primary,secondary
> and sub-ordinate bus numbers of type 1 header 18th offset of ECAM.

This code removal sounds like a separate logical change that could be
a separate patch.

s/primary,secondary/primary, secondary/ (twice)
s/removing/remove/

> Signed-off-by: Thippeswamy Havalige <thippeswamy.havalige at amd.com>
> Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada at amd.com>
> ---
> | Reported-by: kernel test robot <lkp at intel.com>
> | Closes: 
> | https://lore.kernel.org/oe-kbuild-all/202308040330.eMTjX3tF-lkp@intel.
> | com/
> ---
>  drivers/pci/controller/pcie-xilinx-nwl.c | 18 +++---------------
>  1 file changed, 3 insertions(+), 15 deletions(-)
> 
> diff --git a/drivers/pci/controller/pcie-xilinx-nwl.c b/drivers/pci/controller/pcie-xilinx-nwl.c
> index 176686b..b515019 100644
> --- a/drivers/pci/controller/pcie-xilinx-nwl.c
> +++ b/drivers/pci/controller/pcie-xilinx-nwl.c
> @@ -126,7 +126,7 @@
>  #define E_ECAM_CR_ENABLE		BIT(0)
>  #define E_ECAM_SIZE_LOC			GENMASK(20, 16)
>  #define E_ECAM_SIZE_SHIFT		16
> -#define NWL_ECAM_VALUE_DEFAULT		12
> +#define NWL_ECAM_VALUE_DEFAULT		16
>  
>  #define CFG_DMA_REG_BAR			GENMASK(2, 0)
>  #define CFG_PCIE_CACHE			GENMASK(7, 0)
> @@ -165,8 +165,6 @@ struct nwl_pcie {
>  	u32 ecam_size;
>  	int irq_intx;
>  	int irq_misc;
> -	u32 ecam_value;
> -	u8 last_busno;
>  	struct nwl_msi msi;
>  	struct irq_domain *legacy_irq_domain;
>  	struct clk *clk;
> @@ -625,7 +623,7 @@ static int nwl_pcie_bridge_init(struct nwl_pcie *pcie)
>  {
>  	struct device *dev = pcie->dev;
>  	struct platform_device *pdev = to_platform_device(dev);
> -	u32 breg_val, ecam_val, first_busno = 0;
> +	u32 breg_val, ecam_val;
>  	int err;
>  
>  	breg_val = nwl_bridge_readl(pcie, E_BREG_CAPABILITIES) & BREG_PRESENT;
> @@ -675,7 +673,7 @@ static int nwl_pcie_bridge_init(struct nwl_pcie *pcie)
>  			  E_ECAM_CR_ENABLE, E_ECAM_CONTROL);
>  
>  	nwl_bridge_writel(pcie, nwl_bridge_readl(pcie, E_ECAM_CONTROL) |
> -			  (pcie->ecam_value << E_ECAM_SIZE_SHIFT),
> +			  (NWL_ECAM_VALUE_DEFAULT << E_ECAM_SIZE_SHIFT),
>  			  E_ECAM_CONTROL);
>  
>  	nwl_bridge_writel(pcie, lower_32_bits(pcie->phys_ecam_base),
> @@ -683,15 +681,6 @@ static int nwl_pcie_bridge_init(struct nwl_pcie *pcie)
>  	nwl_bridge_writel(pcie, upper_32_bits(pcie->phys_ecam_base),
>  			  E_ECAM_BASE_HI);
>  
> -	/* Get bus range */
> -	ecam_val = nwl_bridge_readl(pcie, E_ECAM_CONTROL);
> -	pcie->last_busno = (ecam_val & E_ECAM_SIZE_LOC) >> E_ECAM_SIZE_SHIFT;
> -	/* Write primary, secondary and subordinate bus numbers */
> -	ecam_val = first_busno;
> -	ecam_val |= (first_busno + 1) << 8;
> -	ecam_val |= (pcie->last_busno << E_ECAM_SIZE_SHIFT);
> -	writel(ecam_val, (pcie->ecam_base + PCI_PRIMARY_BUS));
> -
>  	if (nwl_pcie_link_up(pcie))
>  		dev_info(dev, "Link is UP\n");
>  	else
> @@ -792,7 +781,6 @@ static int nwl_pcie_probe(struct platform_device *pdev)
>  	pcie = pci_host_bridge_priv(bridge);
>  
>  	pcie->dev = dev;
> -	pcie->ecam_value = NWL_ECAM_VALUE_DEFAULT;
>  
>  	err = nwl_pcie_parse_dt(pcie, pdev);
>  	if (err) {
> -- 
> 1.8.3.1
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel