[PATCH 10/13] arm64: dts: ti: k3-j7200: Enable GPIO nodes at the board level

[Andrew Davis]

On 8/7/23 12:38 AM, Dhruva Gole wrote:
> Andrew,
> 
> On 03/08/23 02:23, Andrew Davis wrote:
>> GPIO nodes defined in the top-level J7200 SoC dtsi files are incomplete
>> and may not be functional unless they are extended with pinmux and
>> device information.
>>
>> Disable the GPIO nodes in the dtsi files and only enable the ones that
>> are actually pinned out on a given board.
>>
>> Signed-off-by: Andrew Davis <afd at ti.com>
>> ---
>>   .../boot/dts/ti/k3-j7200-common-proc-board.dts | 18 ++++--------------
>>   arch/arm64/boot/dts/ti/k3-j7200-main.dtsi      |  4 ++++
>>   .../arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi |  2 ++
>>   3 files changed, 10 insertions(+), 14 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> index dee9056f56051..4a5c4f36baeec 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> @@ -240,27 +240,17 @@ &main_uart3 {
>>       pinctrl-0 = <&main_uart3_pins_default>;
>>   };
>> -&main_gpio2 {
>> -    status = "disabled";
>> -};
>> -
>> -&main_gpio4 {
>> -    status = "disabled";
>> -};
>> -
>> -&main_gpio6 {
>> -    status = "disabled";
>> +&main_gpio0 {
>> +    status = "okay";
>> +    /* default pins */
> 
> Small question, where is the pmx for main_gpio0? What does "default pins"
> refer to here? Where are they pinmuxed?
> 

Good question, where is the pmx for main_gpio0? I don't know, it was
never defined before either, we only are noticing this now as we are
disabling by default instead of leaving an unfinished node enabled
by default. (another benefit of this disabled by default scheme).

What is really happening is GPIO nodes we tend to pinmux differently
than normal device nodes. Their pinmux selections tends to be spread
out in all the nodes that make use of these GPIO pins, not all together
here in this node.

For instance in this device we use one of the main_gpio0 pins as a
GPIO toggled regulator, and we define the pinmux for it in that node
(see vdd-sd-dv-default-pins).

We can either define the rest of the pins not used elsewhere
here, or we can consider GPIO an exception to the rule, I'd say
the latter is fine for now.

Andrew

>>   };
>>   &wkup_gpio0 {
>> +    status = "okay";
>>       pinctrl-names = "default";
>>       pinctrl-0 = <&wkup_gpio_pins_default>;
>>   };
>> -&wkup_gpio1 {
>> -    status = "disabled";
>> -};
>> -
>>   &mcu_cpsw {
>>       pinctrl-names = "default";
>>       pinctrl-0 = <&mcu_cpsw_pins_default>, <&mcu_mdio_pins_default>;
>> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
>> index 5d7542ba41b93..6a776f3bbcb19 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
>> +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
>> @@ -832,6 +832,7 @@ main_gpio0: gpio at 600000 {
>>           power-domains = <&k3_pds 105 TI_SCI_PD_EXCLUSIVE>;
>>           clocks = <&k3_clks 105 0>;
>>           clock-names = "gpio";
>> +        status = "disabled";
>>       };
>>       main_gpio2: gpio at 610000 {
>> @@ -849,6 +850,7 @@ main_gpio2: gpio at 610000 {
>>           power-domains = <&k3_pds 107 TI_SCI_PD_EXCLUSIVE>;
>>           clocks = <&k3_clks 107 0>;
>>           clock-names = "gpio";
>> +        status = "disabled";
>>       };
>>       main_gpio4: gpio at 620000 {
>> @@ -866,6 +868,7 @@ main_gpio4: gpio at 620000 {
>>           power-domains = <&k3_pds 109 TI_SCI_PD_EXCLUSIVE>;
>>           clocks = <&k3_clks 109 0>;
>>           clock-names = "gpio";
>> +        status = "disabled";
>>       };
>>       main_gpio6: gpio at 630000 {
>> @@ -883,6 +886,7 @@ main_gpio6: gpio at 630000 {
>>           power-domains = <&k3_pds 111 TI_SCI_PD_EXCLUSIVE>;
>>           clocks = <&k3_clks 111 0>;
>>           clock-names = "gpio";
>> +        status = "disabled";
>>       };
>>       main_spi0: spi at 2100000 {
>> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
>> index 571eb0e2eac92..5ae7320efad7b 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
>> +++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
>> @@ -297,6 +297,7 @@ wkup_gpio0: gpio at 42110000 {
>>           power-domains = <&k3_pds 113 TI_SCI_PD_EXCLUSIVE>;
>>           clocks = <&k3_clks 113 0>;
>>           clock-names = "gpio";
>> +        status = "disabled";
>>       };
>>       wkup_gpio1: gpio at 42100000 {
>> @@ -313,6 +314,7 @@ wkup_gpio1: gpio at 42100000 {
>>           power-domains = <&k3_pds 114 TI_SCI_PD_EXCLUSIVE>;
>>           clocks = <&k3_clks 114 0>;
>>           clock-names = "gpio";
>> +        status = "disabled";
>>       };
>>       mcu_navss: bus at 28380000 {
>