[PATCH] arm64: dts: ti: k3-j784s4-evm: Correct Pin mux offset for ospi

[Udit Kumar]

After splitting wkup_pmx pin mux for J784S4 into four regions.
Pin mux offset for OSPI nodes were not updated to align with new
regions, due to this while setting ospi pin muxes out of range
error was seen.

Pin mux offsets for OSPI nodes are corrected in this patch.

Fixes: 14462bd0b247 ("arm64: dts: ti: k3-j784s4: Fix wakeup pinmux range and pinctrl node offsets")
Signed-off-by: Udit Kumar <u-kumar1 at ti.com>
---
Original test log
https://gist.github.com/uditkumarti/85b5076df99c3019aa56da4268724295
line 1104 and 1107, out of range error is seen

Test log with patch
https://gist.github.com/uditkumarti/29b424d0a1527e77947f72d2e8a38f01

 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 31 +++++++++++++++---------
 1 file changed, 19 insertions(+), 12 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index 7ad152a1b90f..1961cd819f5e 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -379,21 +379,28 @@ J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D34) MCU_OSPI0_D5 */
 			J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (E34) MCU_OSPI0_D6 */
 			J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (E33) MCU_OSPI0_D7 */
 			J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
-			J784S4_WKUP_IOPAD(0x03c, PIN_OUTPUT, 6) /* (C32) MCU_OSPI0_CSn3.MCU_OSPI0_ECC_FAIL */
-			J784S4_WKUP_IOPAD(0x038, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_CSn2.MCU_OSPI0_RESET_OUT0 */
+		>;
+	};
+};
+
+&wkup_pmx1 {
+	mcu_fss0_ospi0_pins1_default: mcu-fss0-ospi0-default-pins1 {
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x004, PIN_OUTPUT, 6) /* (C32) MCU_OSPI0_ECC_FAIL */
+			J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_RESET_OUT0 */
 		>;
 	};
 
-	mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins {
+	mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-pins-default {
 		pinctrl-single,pins = <
-			J784S4_WKUP_IOPAD(0x040, PIN_OUTPUT, 0) /* (F32) MCU_OSPI1_CLK */
-			J784S4_WKUP_IOPAD(0x05c, PIN_OUTPUT, 0) /* (G32) MCU_OSPI1_CSn0 */
-			J784S4_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (E35) MCU_OSPI1_D0 */
-			J784S4_WKUP_IOPAD(0x050, PIN_INPUT, 0) /* (D31) MCU_OSPI1_D1 */
-			J784S4_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (G31) MCU_OSPI1_D2 */
-			J784S4_WKUP_IOPAD(0x058, PIN_INPUT, 0) /* (F33) MCU_OSPI1_D3 */
-			J784S4_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (F31) MCU_OSPI1_DQS */
-			J784S4_WKUP_IOPAD(0x044, PIN_INPUT, 0) /* (C31) MCU_OSPI1_LBCLKO */
+			J784S4_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (F32) MCU_OSPI1_CLK */
+			J784S4_WKUP_IOPAD(0x024, PIN_OUTPUT, 0) /* (G32) MCU_OSPI1_CSn0 */
+			J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (E35) MCU_OSPI1_D0 */
+			J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (D31) MCU_OSPI1_D1 */
+			J784S4_WKUP_IOPAD(0x01C, PIN_INPUT, 0) /* (G31) MCU_OSPI1_D2 */
+			J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (F33) MCU_OSPI1_D3 */
+			J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F31) MCU_OSPI1_DQS */
+			J784S4_WKUP_IOPAD(0x00C, PIN_INPUT, 0) /* (C31) MCU_OSPI1_LBCLKO */
 		>;
 	};
 };
@@ -437,7 +444,7 @@ &fss {
 &ospi0 {
 	status = "okay";
 	pinctrl-names = "default";
-	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>, <&mcu_fss0_ospi0_pins1_default>;
 
 	flash at 0 {
 		compatible = "jedec,spi-nor";
-- 
2.34.1