[PATCH v3 1/6] arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs

Esteban Blanc eblanc at baylibre.com
Mon Apr 17 08:48:27 PDT 2023


This patch adds support for TPS6594 PMIC family on wakup I2C0 bus.
Theses devices provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.

Signed-off-by: Esteban Blanc <eblanc at baylibre.com>
---
 arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 175 ++++++++++++++++++++
 1 file changed, 175 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
index fa44ed4c17d5..d2587c24180f 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
@@ -118,6 +118,25 @@ J721E_WKUP_IOPAD(0x0008, PIN_INPUT, 0)  /* MCU_OSPI0_DQS */
 	};
 };
 
+&wkup_pmx2 {
+	/* wkup_pmx2 starts at 0x68 */
+	wkup_i2c0_pins_default: wkup-i2c0-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x98, PIN_INPUT_PULLUP, 0) /* (F20) WKUP_I2C0_SCL */
+			J721E_WKUP_IOPAD(0x9c, PIN_INPUT_PULLUP, 0) /* (H21) WKUP_I2C0_SDA */
+		>;
+	};
+};
+
+&wkup_pmx3 {
+	/* wkup_pmx3 starts at 0x174 */
+	pmic_irq_pins_default: pmic-irq-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 7) /* (E18) WKUP_GPIO0_84 */
+		>;
+	};
+};
+
 &main_pmx0 {
 	main_i2c0_pins_default: main-i2c0-pins-default {
 		pinctrl-single,pins = <
@@ -231,3 +250,159 @@ flash at 0 {
 		cdns,read-delay = <4>;
 	};
 };
+
+&wkup_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&wkup_i2c0_pins_default>;
+	clock-frequency = <400000>;
+
+	tps659414: pmic at 48 {
+		compatible = "ti,tps6594-q1";
+		reg = <0x48>;
+		ti,primary-pmic;
+		system-power-controller;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_irq_pins_default>;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <84 IRQ_TYPE_EDGE_FALLING>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		buck1-supply = <&vsys_3v3>;
+		buck2-supply = <&vsys_3v3>;
+		buck3-supply = <&vsys_3v3>;
+		buck4-supply = <&vsys_3v3>;
+		buck5-supply = <&vsys_3v3>;
+		ldo1-supply = <&vsys_3v3>;
+		ldo2-supply = <&vsys_3v3>;
+		ldo3-supply = <&vsys_3v3>;
+		ldo4-supply = <&vsys_3v3>;
+
+		regulators {
+			bucka1: buck1 {
+				regulator-name = "vda_mcu_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka2: buck2 {
+				regulator-name = "vdd_mcuio_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka3: buck3 {
+				regulator-name = "vdd_mcu_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka4: buck4 {
+				regulator-name = "vdd_ddr_1v1";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka5: buck5 {
+				regulator-name = "vdd_phyio_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa1: ldo1 {
+				regulator-name = "vdd1_lpddr4_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa2: ldo2 {
+				regulator-name = "vda_dll_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa3: ldo3 {
+				regulator-name = "vdd_wk_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa4: ldo4 {
+				regulator-name = "vda_pll_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	lp876441: pmic at 4c {
+		compatible = "ti,lp8764-q1";
+		reg = <0x4c>;
+		system-power-controller;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <84 IRQ_TYPE_EDGE_FALLING>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		buck1-supply = <&vsys_3v3>;
+		buck2-supply = <&vsys_3v3>;
+		buck3-supply = <&vsys_3v3>;
+		buck4-supply = <&vsys_3v3>;
+
+		regulators: regulators {
+			buckb1: buck1 {
+				regulator-name = "vdd_cpu_avs";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <900000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buckb2: buck2 {
+				regulator-name = "vdd_ram_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buckb3: buck3 {
+				regulator-name = "vdd_core_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buckb4: buck4 {
+				regulator-name = "vdd_io_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
-- 
2.39.2




More information about the linux-arm-kernel mailing list