[PATCH 2/6] drm: bridge: samsung-dsim: Fix PMS Calculator on imx8m[mnp]

[Alexander Stein]

Hi,

Am Montag, 17. April 2023, 00:31:24 CEST schrieb Adam Ford:
> On Sun, Apr 16, 2023 at 5:07 PM Marek Vasut <marex at denx.de> wrote:
> > On 4/15/23 12:40, Adam Ford wrote:
> > > According to Table 13-45 of the i.MX8M Mini Reference Manual, the min
> > > and max values for M and  the frequency range for the VCO_out
> > > calculator were incorrect.  This also appears to be the case for the
> > > imx8mn and imx8mp.
> > > 
> > > To fix this, make new variables to hold the min and max values of m
> > > and the minimum value of VCO_out, and update the PMS calculator to
> > > use these new variables instead of using hard-coded values to keep
> > > the backwards compatibility with other parts using this driver.
> > 
> > [...]
> > 
> > >   static const struct samsung_dsim_driver_data imx8mm_dsi_driver_data =
> > >   {
> > > 
> > > @@ -470,6 +485,9 @@ static const struct samsung_dsim_driver_data
> > > imx8mm_dsi_driver_data = {> > 
> > >        */
> > >       
> > >       .pll_p_offset = 14,
> > >       .reg_values = imx8mm_dsim_reg_values,
> > > 
> > > +     .m_min = 64,
> > > +     .m_max = 1023,
> > > +     .vco_min = 1050,
> > 
> > You might want to call this 'min_freq' since there is a 'max_freq' which
> > seems to indicate what VCO max frequency is.
> > 
> > Note that the same datasheet contains the following information:
> > "
> > MIPI_DPHY_M_PLLPMS field descriptions
> > 
> > 12–4 PMS_M
> > Specifies the PLL PMS value for the M divider
> > NOTE: The programmable divider range should be within 25 to 125 to
> > ensure PLL stability.
> 
> I was confused by this because this statement is not consistent with
> the link they reference jumps me to the table where it reads M is
> between 64 and 1023.
> 
> > NOTE: The M and P divider values should be considered together to ensure
> > VCO ouput frequency
> > (VCO_out) range is between 350 MHz to 750 MHz.
> > Please refer to the topic DPHY PLL for more information.
> 
> I was confused by this too, because the NXP documentation reads the
> 350 - 750MHz that you state, but  "Table 13-45: DPHY PLL Parameters"
> which immediately follows that sentence  on page 4158 shows VCO_out is
> between 1050-2100 MHz.
> 
> I compared the PMS values for a variety of frequencies to those that
> were set in the downstream NXP code, and the PMS values matched.
> Maybe someone from NXP can explain the discrepancy.

Also note that, according to Table 13-28 in RM (Rev 2 07/2022) for i.MX8M 
Nano, VCO_out and Fout has a maximum of 1500MHz only. Although the note above 
mentions a range  of 1050-2100MHz...

Best regards,
Alexander
-- 
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
http://www.tq-group.com/