[PATCH v13 00/15] phy: Add support for Lynx 10G SerDes
Sean Anderson
sean.anderson at seco.com
Tue Apr 11 11:42:57 PDT 2023
This adds support for the Lynx 10G SerDes found on the QorIQ T-series
and Layerscape series. Due to limited time and hardware, only support
for the LS1046ARDB and LS1088ARDB is added in this initial series.
This series is ready for review by the phy maintainers. I have addressed
all known feedback and there are no outstanding issues.
There are several stand-alone commits in this series. Please feel free
to pick them as appropriate. In particular, commits 1, 3, 4, 12, 13, and
14 are all good candidates for picking.
Major reconfiguration of baud rate (e.g. 1G->10G) does not work. From my
testing, SerDes register settings appear identical. The issue appears to
be between the PCS and the MAC. The link itself comes up at both ends,
and a mac loopback succeeds. However, a PCS loopback results in dropped
packets. Perhaps there is some undocumented register in the PCS?
I suspect this driver is around 95% complete, but I don't have the
documentation to make it work completely. At the very least it is useful
for two cases:
- Although this is untested, it should support 2.5G SGMII as well as
1000BASE-KX. The latter needs MAC and PCS support, but the former
should work out of the box.
- It allows for clock configurations not supported by the RCW. This is
very useful if you want to use e.g. SRDS_PRTCL_S1=0x3333 and =0x1133
on the same board. This is because the former setting will use PLL1
as the 1G reference, but the latter will use PLL1 as the 10G
reference. Because we can reconfigure the PLLs, it is possible to
always use PLL1 as the 1G reference.
Changes in v13:
- Fix references to brcm,bcm63xx-gpio.yaml (neé brcm,bcm6345-gpio)
- Split interrupt changes off from serdes support
- Split off SFP addition from serdes support
Changes in v12:
- Put compatible first
- Keep gpio-controller to one line
- Add little-endian property
- Alphabetize compatibles
- Remove some comments
- Remove some examples with insufficient novelty
Changes in v11:
- Keep empty (or almost-empty) properties on a single line
- Don't use | unnecessarily
- Use gpio as the node name for examples
- Rename brcm,bcm6345-gpio.yaml to brcm,bcm63xx-gpio.yaml
Changes in v10:
- Convert gpio-mmio to yaml
- Add compatible for QIXIS
- Remove unnecessary inclusion of clk.h
- Don't gate clocks in compatibility mode
- Fix debugging print with incorrect error variable
- Move serdes bindings to SoC dtsi
- Add support for all (ethernet) serdes modes
- Refer to "nodes" instead of "bindings"
- Move compatible/reg first
Changes in v9:
- Add fsl,unused-lanes-reserved to allow for a gradual transition
between firmware and Linux control of the SerDes
- Change phy-type back to fsl,type, as I was getting the error
'#phy-cells' is a dependency of 'phy-type'
- Convert some u32s to unsigned long to match arguments
- Switch from round_rate to determine_rate
- Drop explicit reference to reference clock
- Use .parent_names when requesting parents
- Use devm_clk_hw_get_clk to pass clocks back to serdes
- Fix indentation
- Split off clock "driver" into its own patch to allow for better
review.
- Add ability to defer lane initialization to phy_init. This allows
for easier transitioning between firmware-managed serdes and Linux-
managed serdes, as the consumer (such as dpaa2, which knows what the
firmware is doing) has the last say on who gets control.
- Fix name of phy mode node
- Add fsl,unused-lanes-reserved to allow a gradual transition, depending
on the mac link type.
- Remove unused clocks
- Fix some phy mode node names
Changes in v8:
- Remove unused variable from lynx_ls_mode_init
- Rename serdes phy handles to use _A, _B, etc. instead of _0, _1, etc.
This should help remind readers that the numbering corresponds to the
physical layout of the registers, and not the lane (pin) number.
- Prevent PCSs from probing as phys
- Rename serdes phy handles like the LS1046A
- Add SFP slot binding
- Fix incorrect lane ordering (it's backwards on the LS1088A just like it is in
the LS1046A).
- Fix duplicated lane 2 (it should have been lane 3).
- Fix incorrectly-documented value for XFI1.
- Remove interrupt for aquantia phy. It never fired for whatever reason,
preventing the link from coming up.
- Add GPIOs for QIXIS FPGA.
- Enable MAC1 PCS
- Remove si5341 binding
Changes in v7:
- Use double quotes everywhere in yaml
- Break out call order into generic documentation
- Refuse to switch "major" protocols
- Update Kconfig to reflect restrictions
- Remove set/clear of "pcs reset" bit, since it doesn't seem to fix
anything.
Changes in v6:
- Bump PHY_TYPE_2500BASEX to 13, since PHY_TYPE_USXGMII was added in the
meantime
- fsl,type -> phy-type
- frequence -> frequency
- Update MAINTAINERS to include new files
- Include bitfield.h and slab.h to allow compilation on non-arm64
arches.
- Depend on COMMON_CLK and either layerscape/ppc
- XGI.9 -> XFI.9
Changes in v5:
- Update commit description
- Dual id header
- Remove references to PHY_INTERFACE_MODE_1000BASEKX to allow this
series to be applied directly to linux/master.
- Add fsl,lynx-10g.h to MAINTAINERS
Changes in v4:
- Add 2500BASE-X and 10GBASE-R phy types
- Use subnodes to describe lane configuration, instead of describing
PCCRs. This is the same style used by phy-cadence-sierra et al.
- Add ids for Lynx 10g PLLs
- Rework all debug statements to remove use of __func__. Additional
information has been provided as necessary.
- Consider alternative parent rates in round_rate and not in set_rate.
Trying to modify out parent's rate in set_rate will deadlock.
- Explicitly perform a stop/reset sequence in set_rate. This way we
always ensure that the PLL is properly stopped.
- Set the power-down bit when disabling the PLL. We can do this now that
enable/disable aren't abused during the set rate sequence.
- Fix typos in QSGMII_OFFSET and XFI_OFFSET
- Rename LNmTECR0_TEQ_TYPE_PRE to LNmTECR0_TEQ_TYPE_POST to better
reflect its function (adding post-cursor equalization).
- Use of_clk_hw_onecell_get instead of a custom function.
- Return struct clks from lynx_clks_init instead of embedding lynx_clk
in lynx_priv.
- Rework PCCR helper functions; T-series SoCs differ from Layerscape SoCs
primarily in the layout and offset of the PCCRs. This will help bring a
cleaner abstraction layer. The caps have been removed, since this handles the
only current usage.
- Convert to use new binding format. As a result of this, we no longer need to
have protocols for PCIe or SATA. Additionally, modes now live in lynx_group
instead of lynx_priv.
- Remove teq from lynx_proto_params, since it can be determined from
preq_ratio/postq_ratio.
- Fix an early return from lynx_set_mode not releasing serdes->lock.
- Rename lynx_priv.conf to .cfg, since I kept mistyping it.
Changes in v3:
- Manually expand yaml references
- Add mode configuration to device tree
- Rename remaining references to QorIQ SerDes to Lynx 10G
- Fix PLL enable sequence by waiting for our reset request to be cleared
before continuing. Do the same for the lock, even though it isn't as
critical. Because we will delay for 1.5ms on average, use prepare
instead of enable so we can sleep.
- Document the status of each protocol
- Fix offset of several bitfields in RECR0
- Take into account PLLRST_B, SDRST_B, and SDEN when considering whether
a PLL is "enabled."
- Only power off unused lanes.
- Split mode lane mask into first/last lane (like group)
- Read modes from device tree
- Use caps to determine whether KX/KR are supported
- Move modes to lynx_priv
- Ensure that the protocol controller is not already in-use when we try
to configure a new mode. This should only occur if the device tree is
misconfigured (e.g. when QSGMII is selected on two lanes but there is
only one QSGMII controller).
- Split PLL drivers off into their own file
- Add clock for "ext_dly" instead of writing the bit directly (and
racing with any clock code).
- Use kasprintf instead of open-coding the snprintf dance
- Support 1000BASE-KX in lynx_lookup_proto. This still requires PCS
support, so nothing is truly "enabled" yet.
- Describe modes in device tree
- ls1088a: Add serdes bindings
Changes in v2:
- Rename to fsl,lynx-10g.yaml
- Refer to the device in the documentation, rather than the binding
- Move compatible first
- Document phy cells in the description
- Allow a value of 1 for phy-cells. This allows for compatibility with
the similar (but according to Ioana Ciornei different enough) lynx-28g
binding.
- Remove minItems
- Use list for clock-names
- Fix example binding having too many cells in regs
- Add #clock-cells. This will allow using assigned-clocks* to configure
the PLLs.
- Document the structure of the compatible strings
- Rename driver to Lynx 10G (etc.)
- Fix not clearing group->pll after disabling it
- Support 1 and 2 phy-cells
- Power off lanes during probe
- Clear SGMIIaCR1_PCS_EN during probe
- Rename LYNX_PROTO_UNKNOWN to LYNX_PROTO_NONE
- Handle 1000BASE-KX in lynx_proto_mode_prep
- Use one phy cell for SerDes1, since no lanes can be grouped
- Disable SerDes by default to prevent breaking boards inadvertently.
Sean Anderson (15):
dt-bindings: phy: Add 2500BASE-X and 10GBASE-R
dt-bindings: phy: Add Lynx 10G phy binding
dt-bindings: Convert gpio-mmio to yaml
dt-bindings: gpio-mmio: Add compatible for QIXIS
dt-bindings: clock: Add ids for Lynx 10g PLLs
clk: Add Lynx 10G SerDes PLL driver
phy: fsl: Add Lynx 10G SerDes driver
phy: lynx10g: Enable by default on Layerscape
arm64: dts: ls1046a: Add serdes nodes
arm64: dts: ls1046ardb: Add serdes descriptions
arm64: dts: ls1088a: Add serdes nodes
arm64: dts: ls1088a: Prevent PCSs from probing as phys
arm64: dts: ls1088ardb: Remove aquantia interrupt
arm64: dts: ls1088ardb: Add SFP cage
arm64: dts: ls1088ardb: Add serdes descriptions
...m6345-gpio.yaml => brcm,bcm63xx-gpio.yaml} | 16 +-
.../devicetree/bindings/gpio/gpio-mmio.yaml | 123 ++
.../bindings/gpio/ni,169445-nand-gpio.txt | 38 -
.../devicetree/bindings/gpio/wd,mbl-gpio.txt | 38 -
.../mfd/brcm,bcm6318-gpio-sysctl.yaml | 4 +-
.../mfd/brcm,bcm63268-gpio-sysctl.yaml | 4 +-
.../mfd/brcm,bcm6328-gpio-sysctl.yaml | 4 +-
.../mfd/brcm,bcm6358-gpio-sysctl.yaml | 4 +-
.../mfd/brcm,bcm6362-gpio-sysctl.yaml | 4 +-
.../mfd/brcm,bcm6368-gpio-sysctl.yaml | 4 +-
.../devicetree/bindings/phy/fsl,lynx-10g.yaml | 248 ++++
Documentation/driver-api/phy/index.rst | 1 +
Documentation/driver-api/phy/lynx_10g.rst | 58 +
MAINTAINERS | 9 +
.../boot/dts/freescale/fsl-ls1046a-rdb.dts | 26 +
.../arm64/boot/dts/freescale/fsl-ls1046a.dtsi | 111 ++
.../boot/dts/freescale/fsl-ls1088a-rdb.dts | 82 +-
.../arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 156 ++-
drivers/clk/Makefile | 1 +
drivers/clk/clk-fsl-lynx-10g.c | 510 +++++++
drivers/phy/freescale/Kconfig | 23 +
drivers/phy/freescale/Makefile | 1 +
drivers/phy/freescale/phy-fsl-lynx-10g.c | 1224 +++++++++++++++++
include/dt-bindings/clock/fsl,lynx-10g.h | 14 +
include/dt-bindings/phy/phy.h | 2 +
include/linux/phy/lynx-10g.h | 16 +
26 files changed, 2606 insertions(+), 115 deletions(-)
rename Documentation/devicetree/bindings/gpio/{brcm,bcm6345-gpio.yaml => brcm,bcm63xx-gpio.yaml} (78%)
create mode 100644 Documentation/devicetree/bindings/gpio/gpio-mmio.yaml
delete mode 100644 Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt
delete mode 100644 Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt
create mode 100644 Documentation/devicetree/bindings/phy/fsl,lynx-10g.yaml
create mode 100644 Documentation/driver-api/phy/lynx_10g.rst
create mode 100644 drivers/clk/clk-fsl-lynx-10g.c
create mode 100644 drivers/phy/freescale/phy-fsl-lynx-10g.c
create mode 100644 include/dt-bindings/clock/fsl,lynx-10g.h
create mode 100644 include/linux/phy/lynx-10g.h
--
2.35.1.1320.gc452695387.dirty
More information about the linux-arm-kernel
mailing list