[PATCH 5/5] arm64: Add initial support for Blaize BLZP1600 CB2
Krzysztof Kozlowski
krzysztof.kozlowski at linaro.org
Thu Apr 6 10:31:33 PDT 2023
On 06/04/2023 12:22, Niko Pasaloukos wrote:
> Adds support for the Blaize CB2 development board based on
> BLZP1600 SoC. This consists of a Carrier-Board and a SoM.
>
> The blaize-blzp1600.dtsi is the common part for the SoC,
> blaize-blzp1600-som.dtsi is the common part for the SoM and
> blaize-blzp1600-som-cb2.dts is the board specific file.
>
> Co-developed-by: James Cowgill <james.cowgill at blaize.com>
> Signed-off-by: James Cowgill <james.cowgill at blaize.com>
> Co-developed-by: Matt Redfearn <matt.redfearn at blaize.com>
> Signed-off-by: Matt Redfearn <matt.redfearn at blaize.com>
> Co-developed-by: Neil Jones <neil.jones at blaize.com>
> Signed-off-by: Neil Jones <neil.jones at blaize.com>
> Signed-off-by: Nikolaos Pasaloukos <nikolaos.pasaloukos at blaize.com>
> ---
> arch/arm64/Kconfig.platforms | 5 +
> arch/arm64/boot/dts/Makefile | 1 +
> arch/arm64/boot/dts/blaize/Makefile | 2 +
> .../dts/blaize/blaize-blzp1600-som-cb.dtsi | 217 +++++
> .../dts/blaize/blaize-blzp1600-som-cb2.dts | 103 ++
> .../boot/dts/blaize/blaize-blzp1600-som.dtsi | 104 ++
> .../boot/dts/blaize/blaize-blzp1600.dtsi | 894 ++++++++++++++++++
> arch/arm64/configs/defconfig | 1 +
DTS cannot go with defconfig or other pieces. DTS is separate, always.
> 8 files changed, 1327 insertions(+)
> create mode 100644 arch/arm64/boot/dts/blaize/Makefile
> create mode 100644 arch/arm64/boot/dts/blaize/blaize-blzp1600-som-cb.dtsi
> create mode 100644 arch/arm64/boot/dts/blaize/blaize-blzp1600-som-cb2.dts
> create mode 100644 arch/arm64/boot/dts/blaize/blaize-blzp1600-som.dtsi
> create mode 100644 arch/arm64/boot/dts/blaize/blaize-blzp1600.dtsi
>
> diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
> index 333d0af650d2..ab89cb7e557f 100644
> --- a/arch/arm64/Kconfig.platforms
> +++ b/arch/arm64/Kconfig.platforms
> @@ -94,6 +94,11 @@ config ARCH_BITMAIN
> help
> This enables support for the Bitmain SoC Family.
>
> +config ARCH_BLAIZE_BLZP1600
> + bool "Blaize BLZP1600 SoC Platforms"
> + help
> + This enables support for the Blaize BLZP1600 SoC family
> +
> config ARCH_EXYNOS
> bool "ARMv8 based Samsung Exynos SoC family"
> select COMMON_CLK_SAMSUNG
> diff --git a/arch/arm64/boot/dts/Makefile b/arch/arm64/boot/dts/Makefile
> index 7b107fa7414b..d2fd6ab437ac 100644
> --- a/arch/arm64/boot/dts/Makefile
> +++ b/arch/arm64/boot/dts/Makefile
> @@ -9,6 +9,7 @@ subdir-y += apm
> subdir-y += apple
> subdir-y += arm
> subdir-y += bitmain
> +subdir-y += blaize
> subdir-y += broadcom
> subdir-y += cavium
> subdir-y += exynos
> diff --git a/arch/arm64/boot/dts/blaize/Makefile b/arch/arm64/boot/dts/blaize/Makefile
> new file mode 100644
> index 000000000000..968c0d687897
> --- /dev/null
> +++ b/arch/arm64/boot/dts/blaize/Makefile
> @@ -0,0 +1,2 @@
> +# SPDX-License-Identifier: GPL-2.0
> +dtb-$(CONFIG_ARCH_BLAIZE_BLZP1600) += blaize-blzp1600-som-cb2.dtb
> diff --git a/arch/arm64/boot/dts/blaize/blaize-blzp1600-som-cb.dtsi b/arch/arm64/boot/dts/blaize/blaize-blzp1600-som-cb.dtsi
> new file mode 100644
> index 000000000000..be09759f48f9
> --- /dev/null
> +++ b/arch/arm64/boot/dts/blaize/blaize-blzp1600-som-cb.dtsi
> @@ -0,0 +1,217 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (c) 2023 Blaize, Inc. All rights reserved.
> + */
> +
> +#include "blaize-blzp1600-som.dtsi"
> +#include <dt-bindings/net/ti-dp83867.h>
> +
> +/ {
> + aliases {
> + ethernet = &gmac;
> + };
> +
> + sound: sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,name = "BLZP1600-TLV320AIC3100";
> + simple-audio-card,widgets =
> + "Microphone", "Microphone Jack",
> + "Headphone", "Headphone Jack";
> + simple-audio-card,routing =
> + "MIC1LP", "Microphone Jack",
> + "MIC1RP", "Microphone Jack",
> + "MIC1LP", "MICBIAS",
> + "MIC1RP", "MICBIAS",
> + "Headphone Jack", "HPL",
> + "Headphone Jack", "HPR";
> +
> + simple-audio-card,format = "i2s";
> + simple-audio-card,bitclock-master = <&sound0_master>;
> + simple-audio-card,frame-master = <&sound0_master>;
> +
> + simple-audio-card,cpu {
> + sound-dai = <&i2s_slave>;
> + };
> +
> + sound0_master: simple-audio-card,codec {
> + sound-dai = <&audio_codec>;
> + clocks = <&scmi_clk BLZP1600_I2S_CODEC_CLK>;
> + system-clock-frequency = <12500000>;
> + /* board specific crystal/oscillator */
> + assigned-clocks = <&scmi_clk BLZP1600_SRC_I2S_CLK>;
> + assigned-clock-rates = <24576000>;
> + };
> + };
> +
> + regulators {
> + vmmc_sd: regulator-sdio0-en {
> + compatible = "regulator-fixed";
> + regulator-name = "mmc-reg-en";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio0 23 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + startup-delay-us = <100000>;
> + };
> +
> + vmmc_io: regulator-sdio0-io {
> + compatible = "regulator-gpio";
> + regulator-name = "mmc-reg-io";
> + regulator-ramp-delay = <10000>;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
> + states = <1800000 0x0 3300000 0x1>;
> + };
> + };
> +};
> +
> +&canfd0 {
> + status = "okay";
> +};
> +
> +&dsi_panel_0 {
> + reset-gpio = <&gpio0 9 GPIO_ACTIVE_LOW>;
> +};
> +
> +&gmac {
> + status = "okay";
> + snps,reset-delays-us = <0 10000 50000>;
> + snps,reset-gpio = <&gpio0 12 GPIO_ACTIVE_LOW>;
> + phy-handle = <&phy0>;
> + phy-mode = "rgmii-id";
> +
> + mdio {
> + compatible = "snps,dwmac-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + phy0: ethernet-phy at 0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_6_B_NIB>;
> + };
> + };
> +};
> +
> +&gpio0 {
> + status = "okay";
> + gpio-line-names = "PERST_N", /* GPIO_0 */
> + "LM96063_ALERT_N", /* GPIO_1 */
> + "INA3221_PV", /* GPIO_2 */
> + "INA3221_CRIT", /* GPIO_3 */
> + "INA3221_WARN", /* GPIO_4 */
> + "INA3221_TC", /* GPIO_5 */
> + "QSPI0_RST_N", /* GPIO_6 */
> + "LM96063_TCRIT_N", /* GPIO_7 */
> + "DSI_TCH_INT", /* GPIO_8 */
> + "DSI_RST", /* GPIO_9 */
> + "DSI_BL", /* GPIO_10 */
> + "DSI_INT", /* GPIO_11 */
> + "ETH_RST", /* GPIO_12 */
> + "CSI0_RST", /* GPIO_13 */
> + "CSI0_PWDN", /* GPIO_14 */
> + "CSI1_RST", /* GPIO_15 */
> + "CSI1_PWDN", /* GPIO_16 */
> + "CSI2_RST", /* GPIO_17 */
> + "CSI2_PWDN", /* GPIO_18 */
> + "CSI3_RST", /* GPIO_19 */
> + "CSI3_PWDN", /* GPIO_20 */
> + "ADAC_RST", /* GPIO_21 */
> + "SD_SW_VDD", /* GPIO_22 */
> + "SD_PON_VDD", /* GPIO_23 */
> + "GPIO_EXP_INT", /* GPIO_24 */
> + "BOARD_ID_0", /* GPIO_25 */
> + "SDIO1_SW_VDD", /* GPIO_26 */
> + "SDIO1_PON_VDD", /* GPIO_27 */
> + "SDIO2_SW_VDD", /* GPIO_28 */
> + "SDIO2_PON_VDD", /* GPIO_29 */
> + "BOARD_ID_1", /* GPIO_30 */
> + "BOARD_ID_2"; /* GPIO_31 */
> +};
> +
> +&i2c0 {
> + clock-frequency = <100000>;
> + status = "okay";
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + clock-frequency = <100000>;
> + status = "okay";
> +
> + audio_codec: audio-codec at 18 {
> + compatible = "ti,tlv320aic3100";
> + reg = <0x18>;
> + #sound-dai-cells = <0>;
> + ai3x-micbias-vg = <1>; /* 2.0V */
> + reset-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
> + };
> +};
> +
> +&i2c3 {
> + clock-frequency = <100000>;
> + status = "okay";
> +
> + gpio_expander: gpio at 74 {
> + compatible = "ti,tca9539";
> + reg = <0x74>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +};
> +
> +&i2s_master {
> + status = "okay";
> +};
> +
> +&i2s_slave {
> + status = "okay";
> +};
> +
> +&sd {
> + wp-inverted;
> + no-sdio;
> + no-mmc;
> + card-detect-delay = <200>;
> + vmmc-supply = <&vmmc_sd>;
> + vqmmc-supply = <&vmmc_io>;
> + status = "okay";
> +};
> +
> +&sdio0 {
> + no-sd;
> + no-sdio;
> + non-removable;
> + wp-inverted;
> + status = "okay";
> + no-3-3-v;
> +};
> +
> +&spim {
> + //spidev at 2 {
> + // compatible = "spidev";
> + // spi-max-frequency = <100>;
> + // reg = <2>;
> + //};
Don't add dead code to Linux kernel.
> +};
> +
> +&spis {
> + //status = "okay";
> + //
> + //slave {
> + // compatible = "spidev";
> + // status = "okay";
> + // spi-max-frequency = <100>;
> + //};
Same problems.
> +};
> +
> +&usb3 {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/blaize/blaize-blzp1600-som-cb2.dts b/arch/arm64/boot/dts/blaize/blaize-blzp1600-som-cb2.dts
> new file mode 100644
> index 000000000000..09925db3c58a
> --- /dev/null
> +++ b/arch/arm64/boot/dts/blaize/blaize-blzp1600-som-cb2.dts
> @@ -0,0 +1,103 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (c) 2023 Blaize, Inc. All rights reserved.
> + */
> +
> +/dts-v1/;
> +
> +#include "blaize-blzp1600-som-cb.dtsi"
> +
> +/ {
> + model = "Blaize BLZP1600 SoM1600P CB2 Development Board";
> +
> + compatible = "blaize,blzp1600-som-cb2", "blaize,blzp1600";
SoM or board? I commented about this in your bindings patch, so now it
visible more that it is wrong.
> +
> + regulators {
> + vmmc_sdio1: regulator-sdio1-en {
> + compatible = "regulator-fixed";
> + regulator-name = "mmc-sdio1-en";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio0 27 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + startup-delay-us = <100000>;
> + };
> +
> + vmmc_sdio1_io: regulator-sdio1-io {
> + compatible = "regulator-gpio";
> + regulator-name = "mmc-sdio1-io";
> + regulator-ramp-delay = <10000>;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
> + states = <1800000 0x0 3300000 0x1>;
> + };
> + };
> +};
> +
> +&gpio_expander {
> + gpio-line-names = "RSP_PIN_7", /* GPIO_0 */
> + "RSP_PIN_11", /* GPIO_1 */
> + "RSP_PIN_13", /* GPIO_2 */
> + "RSP_PIN_15", /* GPIO_3 */
> + "RSP_PIN_27", /* GPIO_4 */
> + "RSP_PIN_29", /* GPIO_5 */
> + "RSP_PIN_31", /* GPIO_6 */
> + "RSP_PIN_33", /* GPIO_7 */
> + "RSP_PIN_37", /* GPIO_8 */
> + "RSP_PIN_16", /* GPIO_9 */
> + "RSP_PIN_18", /* GPIO_10 */
> + "RSP_PIN_22", /* GPIO_11 */
> + "RSP_PIN_28", /* GPIO_12 */
> + "RSP_PIN_32", /* GPIO_13 */
> + "RSP_PIN_36", /* GPIO_14 */
> + "TP31"; /* GPIO_15 */
> +};
> +
> +&i2c3 {
> + gpio_expander_m2: gpio at 75 {
> + compatible = "ti,tca9539";
> + reg = <0x75>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-line-names = "M2_W_DIS1_N", /* GPIO_0 */
> + "M2_W_DIS2_N", /* GPIO_1 */
> + "M2_UART_WAKE_N", /* GPIO_2 */
> + "M2_COEX3", /* GPIO_3 */
> + "M2_COEX_RXD", /* GPIO_4 */
> + "M2_COEX_TXD", /* GPIO_5 */
> + "M2_VENDOR_PIN40", /* GPIO_6 */
> + "M2_VENDOR_PIN42", /* GPIO_7 */
> + "M2_VENDOR_PIN38", /* GPIO_8 */
> + "M2_SDIO_RST_N", /* GPIO_9 */
> + "M2_SDIO_WAKE_N", /* GPIO_10 */
> + "M2_PETN1", /* GPIO_11 */
> + "M2_PERP1", /* GPIO_12 */
> + "M2_PERN1", /* GPIO_13 */
> + "UIM_SWP", /* GPIO_14 */
> + "UART1_TO_RSP"; /* GPIO_15 */
> + };
> +};
> +
> +&sdio1 {
> + no-mmc;
> + no-sd;
> + non-removable;
> + vmmc-supply = <&vmmc_sdio1>;
> + vqmmc-supply = <&vmmc_sdio1_io>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + //status = "okay";
Don't add dead code.
> + keep-power-in-suspend;
> + no-3-3-v;
> + // Override bits 0-SDR50, 1-SDR104, 2-DDR50 to respect the dtb properties
Why? What do you want to respect? How?
> + sdhci-caps-mask = <0x7 0x0>;
> + sd-uhs-sdr12;
> + sd-uhs-sdr25;
> + sd-uhs-sdr50;
> +
> + mwifiex: wifi at 1 {
> + compatible = "brcm,bcm4329-fmac";
> + reg = <1>;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/blaize/blaize-blzp1600-som.dtsi b/arch/arm64/boot/dts/blaize/blaize-blzp1600-som.dtsi
> new file mode 100644
> index 000000000000..39790ae19a2c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/blaize/blaize-blzp1600-som.dtsi
> @@ -0,0 +1,104 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (c) 2023 Blaize, Inc. All rights reserved.
> + */
> +
> +#include "blaize-blzp1600.dtsi"
> +
> +/ {
> + memory at 1000 {
> + device_type = "memory";
> + reg = <0x0 0x00001000 0xfffff000>;
> + };
> +
> + aliases {
> + serial0 = &uart0;
This is property of the board usualy, not SoC. Although I am not sure
what's this file about - there is already SoM DTSI.
> + };
> +
> + chosen {
> + bootargs = "earlycon";
Nope, that's not for DTS in mainline.
> + stdout-path = "serial0:115200";
> + };
> +};
> +
> +&gsp {
> + blaize,power-limit-peak = <27001>; /* Power in mW */
> +};
> +
> +&i2c4 {
> + clock-frequency = <100000>;
> + status = "okay";
> +
> + hwmon-ina3221 at 40 {
Node names should be generic.
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> + compatible = "ti,ina3221";
> + reg = <0x40>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + input at 0 {
> + reg = <0x0>;
> + label = "dual-rail1-1v1-1v8";
> + shunt-resistor-micro-ohms = <1000>;
> + };
Blank line.
> + input at 1 {
> + reg = <0x1>;
> + label = "single-rail1-0v8";
> + shunt-resistor-micro-ohms = <25000>;
> + };
Ditto
> + input at 2 {
> + reg = <0x2>;
> + label = "dual-rail2-1v1-1v8";
> + shunt-resistor-micro-ohms = <1000>;
> + };
> + };
> +
> + hwmon-lm96063 at 4c {
Node names should be generic.
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> + compatible = "national,lm96163";
> + reg = <0x4c>;
> + };
> +};
> +
> +&spim {
> + status = "okay";
> +
> + flash at 0 {
> + compatible = "jedec,spi-nor";
> + spi-max-frequency = <1000000>;
> + reg = <0>;
Blank line.
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + fip at 0 {
> + label = "fip";
> + reg = <0x0000000 0xe0000>;
> + read-only;
> + };
> +
> + uboot-env at e0000 {
> + label = "u-boot-env";
> + reg = <0xe0000 0x10000>;
> + };
> +
> + dtb at f0000 {
> + label = "dtb";
> + reg = <0xf0000 0x10000>;
> + };
> +
> + image at 100000 {
> + label = "linux";
> + reg = <0x100000 0x800000>;
> + };
> +
> + rfs at 900000 {
> + label = "rfs";
> + reg = <0x900000 0x3700000>;
> + };
> + };
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/blaize/blaize-blzp1600.dtsi b/arch/arm64/boot/dts/blaize/blaize-blzp1600.dtsi
> new file mode 100644
> index 000000000000..5641a95795dc
> --- /dev/null
> +++ b/arch/arm64/boot/dts/blaize/blaize-blzp1600.dtsi
> @@ -0,0 +1,894 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (c) 2023 Blaize, Inc. All rights reserved.
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/reset/blaize,blzp1600-reset.h>
> +#include <dt-bindings/clock/blaize,blzp1600-clk.h>
> +
> +/ {
> + interrupt-parent = <&gic>;
> + #address-cells = <2>;
> + #size-cells = <1>;
> +
> + cpus {
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + cpu0: cpu at 0 {
> + compatible = "arm,cortex-a53";
> + device_type = "cpu";
> + enable-method = "psci";
> + reg = <0x0 0x0>;
> + next-level-cache = <&l2>;
> + };
> +
> + cpu1: cpu at 1 {
> + compatible = "arm,cortex-a53";
> + device_type = "cpu";
> + enable-method = "psci";
> + reg = <0x0 0x1>;
> + next-level-cache = <&l2>;
> + };
> +
> + l2: l2-cache0 {
> + compatible = "cache";
> + cache-level = <2>;
> + };
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupts = /* Physical Secure PPI */
> + <GIC_PPI 13 (GIC_CPU_MASK_RAW(0x3) |
> + IRQ_TYPE_LEVEL_LOW)>,
> + /* Physical Non-Secure PPI */
> + <GIC_PPI 14 (GIC_CPU_MASK_RAW(0x3) |
> + IRQ_TYPE_LEVEL_LOW)>,
> + /* Hypervisor PPI */
> + <GIC_PPI 10 (GIC_CPU_MASK_RAW(0x3) |
> + IRQ_TYPE_LEVEL_LOW)>,
> + /* Virtual PPI */
> + <GIC_PPI 11 (GIC_CPU_MASK_RAW(0x3) |
> + IRQ_TYPE_LEVEL_LOW)>;
> + };
> +
> + psci {
> + compatible = "arm,psci-1.0", "arm,psci-0.2";
> + method = "smc";
> + };
> +
> + hwmon {
> + compatible = "blaize,blzp1600-hwmon";
Undocumented comaptible.
> + clocks = <&scmi_clk BLZP1600_TSENSOR_CLK>;
> + resets = <&scmi_rst BLZP1600_TSENSOR_RST>;
> + };
> +
> + pmu {
> + compatible = "arm,cortex-a53-pmu";
> + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-affinity = <&cpu0>, <&cpu1>;
> + };
> +
> + sram at 0 {
> + /*
> + * On BLZP1600 there is no general purpose (non-secure) SRAM.
> + * A small DDR memory space has been reserved for general use.
> + */
> + compatible = "mmio-sram";
> + reg = <0x0 0x00000000 0x00001000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 0x0 0x00000000 0x1000>;
> +
> + /* SCMI reserved buffer space on DDR space */
> + scmi0_shm: scmi-sram at 800 {
> + compatible = "arm,scmi-shmem";
> + reg = <0x800 0x80>;
> + };
> + };
> +
> + firmware {
> + scmi {
> + compatible = "arm,scmi-smc";
> + arm,smc-id = <0x82002000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + status = "okay";
Drop status.
> + shmem = <&scmi0_shm>;
> +
> + scmi_clk: protocol at 14 {
> + reg = <0x14>;
> + #clock-cells = <1>;
> + };
Missing blank line.
> + scmi_rst: protocol at 16 {
> + reg = <0x16>;
> + #reset-cells = <1>;
> + };
> + };
> + };
> +
> + soc {
> + compatible = "simple-bus";
> + #address-cells = <2>;
> + #size-cells = <1>;
> + ranges;
> +
> + spim: spi at 200300000 {
> + compatible = "snps,dw-apb-ssi";
Just to be sure - there are no dtbs_check warnings? That should be your
important requirement. It's a lot, a lot of work to remove them later.
> + reg = <0x2 0x00300000 0x10000>;
> + clocks = <&scmi_clk BLZP1600_QSPI_CLK>,
> + <&scmi_clk BLZP1600_QSPI_PCLK>;
> + clock-names = "ssi_clk", "pclk";
> + resets = <&scmi_rst BLZP1600_QSPI_RST>,
> + <&scmi_rst BLZP1600_QSPI_PRST>;
> + reset-names = "spi", "pspi";
> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> + reg-io-width = <4>;
> + num-cs = <3>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + gic: interrupt-controller at 200410000 {
> + compatible = "arm,gic-400";
> + #interrupt-cells = <3>;
> + #address-cells = <0>;
> + interrupt-controller;
> + reg = <0x2 0x00410000 0x20000>,
> + <0x2 0x00420000 0x20000>,
> + <0x2 0x00440000 0x20000>,
> + <0x2 0x00460000 0x20000>;
> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_RAW(0x3) |
> + IRQ_TYPE_LEVEL_LOW)>;
> + };
> +
> + public_soc_registers: syscon at 200490000 {
> + compatible = "blaize,blzp1600-sys", "syscon";
Undocumented comaptible.
I will stop review. I don't think your submission is ready for upstream.
Best regards,
Krzysztof
More information about the linux-arm-kernel
mailing list