[PATCH 1/1] arm64: dts: freescale: Add PWM fan support

[Shawn Guo]

On Tue, Oct 18, 2022 at 11:33:41AM +0200, Alexander Stein wrote:
> This adds the support for optional PWM fan 422J/2HP.
> 
> Signed-off-by: Alexander Stein <alexander.stein at ew.tq-group.com>

Board name should be specified in the patch subject to tell this is a
board specific change, maybe something like `arm64: dts: mba8mpxl: ...`?

Shawn

> ---
> Now with inverted polarity support for pwm-fan in place, add PWM fan DT
> nodes for TQMa8MPQL + MBa8MPxL. As this is optional, it's disabled by
> default. This is based on next-20221018.
> 
> Note: This device needs 'pwm1_enable' set to 3. E.g. using udev rule:
> SUBSYSTEM=="hwmon", DRIVERS=="pwm-fan", ATTR{pwm1_enable}="3"
> 
>  .../freescale/imx8mp-tqma8mpql-mba8mpxl.dts   | 76 +++++++++++++++++++
>  1 file changed, 76 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dts b/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dts
> index 7a32379cd006..ffd117f17bbe 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dts
> @@ -55,6 +55,21 @@ clk_xtal25: clk-xtal25 {
>  		clock-frequency = <25000000>;
>  	};
>  
> +	fan0: pwm-fan {
> +		compatible = "pwm-fan";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_pwmfan>;
> +		fan-supply = <&reg_pwm_fan>;
> +		#cooling-cells = <2>;
> +		/* typical 25 kHz -> 40.000 nsec */
> +		pwms = <&pwm3 0 40000 PWM_POLARITY_INVERTED>;
> +		cooling-levels = <0 32 64 128 196 240>;
> +		pulses-per-revolution = <2>;
> +		interrupt-parent = <&gpio5>;
> +		interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
> +		status = "disabled";
> +	};
> +
>  	gpio-keys {
>  		compatible = "gpio-keys";
>  		pinctrl-names = "default";
> @@ -115,6 +130,18 @@ display: display {
>  		status = "disabled";
>  	};
>  
> +	reg_pwm_fan: regulator-pwm-fan {
> +		compatible = "regulator-fixed";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_regpwmfan>;
> +		regulator-name = "FAN_PWR";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +		gpio = <&gpio4 27 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		vin-supply = <&reg_vcc_12v0>;
> +	};
> +
>  	reg_usdhc2_vmmc: regulator-usdhc2 {
>  		compatible = "regulator-fixed";
>  		pinctrl-names = "default";
> @@ -172,6 +199,47 @@ linux,cma {
>  			linux,cma-default;
>  		};
>  	};
> +
> +	thermal-zones {
> +		soc-thermal {
> +			trips {
> +				soc_active0: trip-active0 {
> +					temperature = <40000>;
> +					hysteresis = <5000>;
> +					type = "active";
> +				};
> +
> +				soc_active1: trip-active1 {
> +					temperature = <48000>;
> +					hysteresis = <3000>;
> +					type = "active";
> +				};
> +
> +				soc_active2: trip-active2 {
> +					temperature = <60000>;
> +					hysteresis = <10000>;
> +					type = "active";
> +				};
> +			};
> +
> +			cooling-maps {
> +				map1 {
> +					trip = <&soc_active0>;
> +					cooling-device = <&fan0 1 1>;
> +				};
> +
> +				map2 {
> +					trip = <&soc_active1>;
> +					cooling-device = <&fan0 2 2>;
> +				};
> +
> +				map3 {
> +					trip = <&soc_active2>;
> +					cooling-device = <&fan0 3 3>;
> +				};
> +			};
> +		};
> +	};
>  };
>  
>  &ecspi1 {
> @@ -725,10 +793,18 @@ pinctrl_pwm3: pwm3grp {
>  		fsl,pins = <MX8MP_IOMUXC_I2C3_SDA__PWM3_OUT		0x14>;
>  	};
>  
> +	pinctrl_pwmfan: pwmfangrp {
> +		fsl,pins = <MX8MP_IOMUXC_I2C3_SCL__GPIO5_IO18		0x80>; /* FAN RPM */
> +	};
> +
>  	pinctrl_reg12v0: reg12v0grp {
>  		fsl,pins = <MX8MP_IOMUXC_SD1_DATA4__GPIO2_IO06		0x140>; /* VCC12V enable */
>  	};
>  
> +	pinctrl_regpwmfan: regpwmfangrp {
> +		fsl,pins = <MX8MP_IOMUXC_SAI2_MCLK__GPIO4_IO27		0x80>;
> +	};
> +
>  	/* X61 */
>  	pinctrl_uart1: uart1grp {
>  		fsl,pins = <MX8MP_IOMUXC_SD1_CLK__UART1_DCE_TX		0x140>,
> -- 
> 2.25.1
>